Hi Corey - For many years we used Pro Solar racking and Unirac Solarmount and tightened the clamps with impact drivers. At some point maybe roughly 8 years ago, Unirac switched its mid clamps to stainless steel self grounding clamps with teeth to bite into the module frame. We continued to use impacts with no issue. Then, starting around 4 years ago, we started to have module glass failures with our SunPower commercial systems and these Unirac clamps. We immediately switched to torque wrenches for tightening the clamps. However, the failures continued. My guess is that the poor design of the Unirac mid clamps in conjunction with thinner “weaker” module frames exasperated the issue. We now have stopped using those mid clamps and continue to hand tighten all clamps. We primarily install SunPower, and their residential module frames have a lip so all the pressure from the clamp doesn’t go to the glass.
Getting to your question - what kind of mid clamps do you have? If they are aluminum, there may be less risk than the stainless clamps. I would be worried that the process of loosening and then re-tightening might cause more damage than good if there aren’t any problems that have occurred to date. It’s a good question. August Luminalt On Fri, Sep 3, 2021 at 12:06 AM Corey Shalanski <coreso...@gmail.com> wrote: > Wrenches, > > (This question actually does refer to the proper use of 'wrenches'...) > > While inspecting some recent work from one of our contractors, we noted > that the PV module clamps had been torqued to ~150% of the racking > manufacturer's specified value. My question is whether that might have any > detrimental effect on the modules (frame, glass, cells, seal, etc) and > whether it would be worth loosening the clamps and re-torquing them to the > proper spec? For reference, 224 modules are installed. > > We were made aware that the contractor used an impact driver on the > clamps, which accounts for the excessive torque applied. I definitely > understand the temptation to use an impact driver for just about > any hardware that needs turning—but my understanding is also that impact > drivers are generally incompatible with machine screws. So my other > question to the group is whether anyone has had success in dissuading > subcontractors from using impact drivers so liberally on project sites? Any > advice is appreciated. > > -- > Corey Shalanski > Jah Light Solar > Portland, Jamaica > _______________________________________________ > List sponsored by Redwood Alliance > > Pay optional member dues here: http://re-wrenches.org > > List Address: RE-wrenches@lists.re-wrenches.org > > Change listserver email address & settings: > http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org > > There are two list archives for searching. When one doesn't work, try the > other: > https://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/ > http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org > > List rules & etiquette: > http://www.re-wrenches.org/etiquette.htm > > Check out or update participant bios: > http://www.members.re-wrenches.org > > -- August Goers Luminalt o: 415.792.6666 m: 415.559.1525 aug...@luminalt.com
_______________________________________________ List sponsored by Redwood Alliance Pay optional member dues here: http://re-wrenches.org List Address: RE-wrenches@lists.re-wrenches.org Change listserver email address & settings: http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org There are two list archives for searching. When one doesn't work, try the other: https://www.mail-archive.com/re-wrenches@lists.re-wrenches.org/ http://lists.re-wrenches.org/pipermail/re-wrenches-re-wrenches.org List rules & etiquette: http://www.re-wrenches.org/etiquette.htm Check out or update participant bios: http://www.members.re-wrenches.org
