I should have said that I did use the DAG-2 to make sure I had gotten it back where it belonged
From: rbw-owners-bunch@googlegroups.com [mailto:rbw-owners-bunch@googlegroups.com] On Behalf Of Bill Gibson Sent: Thursday, September 26, 2013 9:02 PM To: rbw-owners-bunch@googlegroups.com Subject: Re: [RBW] Sam H. pinched dropout repair advice? You will want to use the Park Tool DAG-2 to align the hanger after gently spreading the dropout to spec. Probably a job for a good shop.The dropout is malleable and will be fine, done right. On Thu, Sep 26, 2013 at 5:11 PM, Eric Daume <ericda...@gmail.com<mailto:ericda...@gmail.com>> wrote: I had a custom frame that came with a dropout that was pretty severely pinched--maybe down to 7mm or so, where it should be 10. I just took a prybar, padded it with a rag, and went at it: https://picasaweb.google.com/lh/photo/frNJ7s6ARvifc5kfr3C8UNMTjNZETYmyPJy0liipFm0?feat=directlink Eric Dublin, OH On Thu, Sep 26, 2013 at 7:16 PM, cbone97 <cbon...@gmail.com<mailto:cbon...@gmail.com>> wrote: I'm preparing to build up the Sam H. I bought used here now that my tires, cables n' stuff are in from Riv. Some time after the frame was delivered I noticed I could slide the rear hub in because the drive side is "pinched" shut just a tiny amount. You can't tell by looking at it. Could've happened in shipping, I don't think the seller knew, and it really doesn't matter. I just want it fixed. In harnessing the power of allmighty google, it looks like most folks suggest just gently leveraging the dropout back open. Any experience or advice with this? I'm not afraid to try, primarily just wondering if I should apply heat or if there's a better method. I wanna be careful not to open the dropout too much. Thanks in advance. Hopefully I'll post pics of my first Riv beautifying the Katy trail soon. -- You received this message because you are subscribed to the Google Groups "RBW Owners Bunch" group. To unsubscribe from this group and stop receiving emails from it, send an email to rbw-owners-bunch+unsubscr...@googlegroups.com<mailto:rbw-owners-bunch%2bunsubscr...@googlegroups.com>. To post to this group, send email to rbw-owners-bunch@googlegroups.com<mailto:rbw-owners-bunch@googlegroups.com>. Visit this group at http://groups.google.com/group/rbw-owners-bunch. For more options, visit https://groups.google.com/groups/opt_out. -- You received this message because you are subscribed to the Google Groups "RBW Owners Bunch" group. To unsubscribe from this group and stop receiving emails from it, send an email to rbw-owners-bunch+unsubscr...@googlegroups.com<mailto:rbw-owners-bunch%2bunsubscr...@googlegroups.com>. To post to this group, send email to rbw-owners-bunch@googlegroups.com<mailto:rbw-owners-bunch@googlegroups.com>. Visit this group at http://groups.google.com/group/rbw-owners-bunch. For more options, visit https://groups.google.com/groups/opt_out. -- Bill Gibson Tempe, Arizona, USA -- You received this message because you are subscribed to the Google Groups "RBW Owners Bunch" group. To unsubscribe from this group and stop receiving emails from it, send an email to rbw-owners-bunch+unsubscr...@googlegroups.com<mailto:rbw-owners-bunch+unsubscr...@googlegroups.com>. To post to this group, send email to rbw-owners-bunch@googlegroups.com<mailto:rbw-owners-bunch@googlegroups.com>. Visit this group at http://groups.google.com/group/rbw-owners-bunch. For more options, visit https://groups.google.com/groups/opt_out. ------------------------------------------------------------------------------ **************************************************** To ensure compliance with Treasury Department regulations, we advise you that, unless otherwise expressly indicated, any federal tax advice contained in this message was not intended or written to be used, and cannot be used, for the purpose of (i) avoiding tax-related penalties under the Internal Revenue Code or applicable state or local tax law provisions or (ii) promoting, marketing or recommending to another party any tax-related matters addressed herein. **************************************************** **************************************************** This email (and any attachments thereto) is intended only for use by the addressee(s) named herein and may contain legally privileged and/or confidential information. If you are not the intended recipient of this email, you are hereby notified that any dissemination, distribution or copying of this email (and any attachments thereto) is strictly prohibited. If you receive this email in error please immediately notify me at (212) 735-3000 and permanently delete the original email (and any copy of any email) and any printout thereof. Further information about the firm, a list of the Partners and their professional qualifications will be provided upon request. **************************************************** ============================================================================== -- You received this message because you are subscribed to the Google Groups "RBW Owners Bunch" group. To unsubscribe from this group and stop receiving emails from it, send an email to rbw-owners-bunch+unsubscr...@googlegroups.com. To post to this group, send email to rbw-owners-bunch@googlegroups.com. Visit this group at http://groups.google.com/group/rbw-owners-bunch. For more options, visit https://groups.google.com/groups/opt_out.
