Remember that every square taper crank fits differently, so they must be 
paired to a specific spindle length, to fit ideally on any specific frame.  
There's really no standard bb width for any given crankset.  Unlike many 
modern, plug-and-play  external bearing cranksets, clearance from 
chainstays, and optimizing Q factor need to be considered as choices, and 
often take precedent over achieving a "perfect" numerical chainline.  
Especially when mixing 80s parts with modern frames.  

I'm a long-time user and fan of suntour cranks, and still have them on 
several bikes.  FWIW, there were at least two or three verions of the XC 
Pro cranks alone, which looked superficially similar but were very 
different.  I assume all were made under contract by Sugino (but don't know 
for sure), but they were different from Sugino-branded cranks as well.  The 
arm profiles/offsets were different, as well as how far they pressed onto 
the taper,  yielding different Q factors and chainstay clearances for any 
given bb spindle length.  Some of the microdrive cranksets had a VERY 
narrow stance, compared to the 110 bcd ones, and thus required a wider bb 
spindle.  This is where Patrick's 127mm ones were probably intended to be 
used, originally.

All that said, I have other newish bikes where I've had to use 127mm and 
130mm spindles, with different square taper cranks, in order to fit certain 
tires or chainstay profiles. If the outer ring of a tripple crank is 
replaced with a pant guard or bash ring, (effectively using the two inner 
chainrings as a double), the chainline (measured between the chainrings) 
isn't even pushed that far out.  If I had the spare cash and wasn't making 
an effort to quit hoarding parts, I'd buy this myself.

On Thursday, January 22, 2026 at 9:38:53 AM UTC-7 Ray Varella wrote:

> To answer what bike would need such a wide spindle. 
> That depends but that bottom bracket would fit a Sugino AT configured with 
> a triple on bikes with a 135mm rear axle. 
> If you have one of those cranks you should grab this, it will save you a 
> bundle by not having to purchase a Phil. 
>
> Ray
> Vallejo CA
>
>
> On Thursday, January 22, 2026 at 7:21:22 AM UTC-8 [email protected] wrote:
>
>> I am a diehard square taper fan. I also like kinda-new mountain bikes. 
>> Kinda new mountain bikes use boost hubs and boost chainline. I've found I 
>> need something in the 127-130mm range at a minimum to get an appropriate 
>> chainline. In some cases even just getting the crank arm to clear the 
>> chainstay can be an issue. This is mostly for bikes that fit 2.8" or bigger 
>> tires.
>>
>> Brian
>>
>> On Thursday, January 22, 2026 at 9:17:03 AM UTC-6 [email protected] 
>> wrote:
>>
>>> Dumb question of the day; what bike configuration would require such a 
>>> wide BB? Fat bike perhaps? I had a wide one on my Gus (121.5?) and it was 
>>> WIDE. Just curious.
>>> Sent from my iPhone
>>>
>>> On Jan 22, 2026, at 1:42 AM, Corwin Zechar <[email protected]> wrote:
>>>
>>> Pictures Patrick?
>>>
>>>
>>> Regards,
>>>
>>>
>>> Corwin
>>> On Friday, January 16, 2026 at 3:19:32 PM UTC-8 Patrick Moore wrote:
>>>
>>>> I won’t highjack this thread too far, but I have a 127 mm Greaseguard 
>>>> bb practically NIB — I say “practically” qualification because I installed 
>>>> and uninstalled it 3 times on my Matthews dirt road bike forlornly hoping 
>>>> I 
>>>> could make it work. Nothing was every tightened down hard.
>>>>
>>>> Anyway, I’ll sell for less than the $100 shipped that I paid for it; 
>>>> let’s say $80 shipped CONUS. And I’d trade for something. I’d like a nice 
>>>> floor pump, for example; an old but still very well working Silca track 
>>>> pump would be fine, as would one of the Rivendell Plumpatire. And I’m open 
>>>> for intriguing trade suggestions, and I’m happy to add or receive 
>>>> additional value, cash or goods, to adjust a deal for fairness.
>>>>
>>>> On Fri, Jan 16, 2026 at 3:14 PM [email protected] <[email protected]> 
>>>> wrote:
>>>>
>>>>> Thanks for the thoughts.  I did not think the grease guard BBs were 
>>>>> currently "get-able" but I just bought one one NOS on eBay.  Will see if 
>>>>> it 
>>>>> lasts longer than 2 Tanges (as that was the price).
>>>>
>>>> -- 
>>> You received this message because you are subscribed to the Google 
>>> Groups "RBW Owners Bunch" group.
>>> To unsubscribe from this group and stop receiving emails from it, send 
>>> an email to [email protected].
>>> To view this discussion visit 
>>> https://groups.google.com/d/msgid/rbw-owners-bunch/4c596167-c9b6-44aa-9875-47dc7a0970cen%40googlegroups.com
>>>  
>>> <https://groups.google.com/d/msgid/rbw-owners-bunch/4c596167-c9b6-44aa-9875-47dc7a0970cen%40googlegroups.com?utm_medium=email&utm_source=footer>
>>> .
>>>
>>>

-- 
You received this message because you are subscribed to the Google Groups "RBW 
Owners Bunch" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to [email protected].
To view this discussion visit 
https://groups.google.com/d/msgid/rbw-owners-bunch/ea59df02-15d6-42b5-b7a3-02b3ab09f192n%40googlegroups.com.

Reply via email to