On 03/22/2012 07:05 AM, Sudhir Harwalkar wrote: > I have replaced current <client> clause with whatever you mentioned below, > but in log file it shows an error.
There's still one line left from the old <Client> clause. Remove this line too: <Client your.client.dns.name.com> > Please see the command line message in screenshot "cmd_msg.PNG" also see the > log file attached with this. You can set log directory with the command line options, but I suggest you replace 'LogDir' and 'DbDir' with these values: LogDir c:/Program Files/Radiator DbDir c:/Program Files/Radiator You should use the new Client clause and the above LogDir and DbDir values in the other configurations files you also try. > Yes my AP IP is 192.168.37.184. Ok. Thanks. More about this in your other message, but briefly: - this address goes into Client: <Client 192.168.37.184> - BindAddress is local address. Use 0.0.0.0 in most cases > In the log file as I found .directory is not found need to mention the path > for directory? > If possible please make changes in the log file attached with this and send > me, I will verify with this. Try the changes above and try running it then. Thanks! Heikki > Thanks in Advance > Sudhir H > > > -----Original Message----- > From: radiator-boun...@open.com.au [mailto:radiator-boun...@open.com.au] On > Behalf Of Heikki Vatiainen > Sent: Thursday, March 22, 2012 4:08 AM > To: radiator@open.com.au > Subject: Re: [RADIATOR] Radiator > > On 03/21/2012 11:40 AM, Sudhir Harwalkar wrote: > >> Thanks Heikki, I installed Net-SSLeay.ppd. > > Ok, good to hear. > >> 1.Please find the radius.cfg file, in that I have added AP IP address and >> Authentication port, is that correct way that I mentioned in the config file >> radius.cfg file or need to make some other things and where do I need to >> mention Shared Secrete. > > Try replacing your current <Client> clause with this: > > Trace 4 > LogStdout > AuthPort 1812 > AcctPort 1813 > # This clause defines a single client to listen to <Client 192.168.37.184> > Secret GSDEMO > </Client> > > AuthPort and AcctPort do not go into Client and I am assuming > 192.168.37.184 is your AP. > > I added Trace 4 and LogStdout so that you will easily see the debug and other > messages on the console. > >> 2. send me command for running radius.cfg file, that I have stored in >> c:/ProgramFile. > > First, see http://www.open.com.au/radiator/install-demo.html and the > installation instructions there. They give examples how to start radiusd > (Radiator). > > Typically something like this should work: > > perl c:\perl\bin\radiusd -trace 4 -config_file c:\path\to\your.conf > > -- > Heikki Vatiainen <h...@open.com.au> > > Radiator: the most portable, flexible and configurable RADIUS server > anywhere. SQL, proxy, DBM, files, LDAP, NIS+, password, NT, Emerald, > Platypus, Freeside, TACACS+, PAM, external, Active Directory, EAP, TLS, TTLS, > PEAP, TNC, WiMAX, RSA, Vasco, Yubikey, MOTP, HOTP, TOTP, DIAMETER etc. Full > source on Unix, Windows, MacOSX, Solaris, VMS, NetWare etc. > _______________________________________________ > radiator mailing list > radiator@open.com.au > http://www.open.com.au/mailman/listinfo/radiator > > > Larsen & Toubro Limited > > www.larsentoubro.com > > This Email may contain confidential or privileged information for the > intended recipient (s) If you are not the intended recipient, please do not > use or disseminate the information, notify the sender and delete it from your > system. -- Heikki Vatiainen <h...@open.com.au> Radiator: the most portable, flexible and configurable RADIUS server anywhere. SQL, proxy, DBM, files, LDAP, NIS+, password, NT, Emerald, Platypus, Freeside, TACACS+, PAM, external, Active Directory, EAP, TLS, TTLS, PEAP, TNC, WiMAX, RSA, Vasco, Yubikey, MOTP, HOTP, TOTP, DIAMETER etc. Full source on Unix, Windows, MacOSX, Solaris, VMS, NetWare etc. _______________________________________________ radiator mailing list radiator@open.com.au http://www.open.com.au/mailman/listinfo/radiator
