Hi Andrea, thats a good tip. Thanks.
I have installed openwrt kamikaze x86 under qemu here and perl as advised. When I installed the perlbase packages, I noticed that the perlbase *dbm packages failed to install. The absence of these modules explains most of the problems you saw in the test suite. When I run 'perl Makefile.pl', is see the same ExtUtils error you saw, and no Makefile was produced. I put this down to a broken OPenWRT perl ExtUtils package. That means you wont be able to do a make install. Nevertheless when running Radiator from within the distribution directory, it starts fine and answers simple requests (at least) from radpwtst. Cheers. On Friday 20 August 2010 09:50:59 am you wrote: > Hi Mike, > > Me too, but came across this command: > > opkg list | grep -o -E perl-\\w+ | xargs opkg install > opkg list | grep -o -E perlbase-\\w+ | xargs opkg install > > > > > > -----Original Message----- > From: Mike McCauley [mailto:[email protected]] > Sent: 20 August 2010 1:42 AM > To: Andrea Coppini (AIR Networks) > Subject: Re: [RADIATOR] Installation on OpenWRT > > Hello Andrea, > > On Friday 20 August 2010 08:54:37 am you wrote: > > Installed OpenWRT (on Metarouter - package sources > > http://openwrt.pantele.com.ua/trunk/metarouter/packages/) > > > > Configured IP settings only > > > > Installed all perl* and perlbase* packages using opkg > > sorry, openwrt beginner: > > how did you Installed all perl* and perlbase* packages using opkg > > Cheers. > > > Downloaded Radiator-Locked-4.7.tgz to the root path (/) > > > > Used gunzip to unpack the file to /Radiator-Locked-4.7/ > > > > Tried to install, failed. > > Tried to run the tests as explained below. > > > > > > > > -----Original Message----- > > From: [email protected] [mailto:[email protected]] > > On > > > Behalf Of Mike McCauley > > Sent: 20 August 2010 12:47 AM > > To: [email protected] > > Subject: Re: [RADIATOR] Installation on OpenWRT > > > > Hello Andrea, > > > > Im going to try to reproduce this. > > What perl did you install? > > precisely how did you install perl? > > > > Cheers. > > > > On Friday 20 August 2010 01:16:06 am Andrea Coppini (AIR Networks) wrote: > > > Hi, > > > > > > I'm trying to install Radiator on an OpenWRT OS (www.openwrt.org). I > > > have 256Mb of disk and 32Mb of RAM allocated to OpenWRT, which should > > > be > > > > plenty. > > > > > I have installed all the Perl and Perlbase modules successfully, and > > > unzipped Radiator-Locked-4.7 to the root. I'm logged in as root, no > > > password (this is a test system). > > > > > > When I run 'perl Makefile.PL', I get the following error: > > > ---- > > > ExtUtils/Install.pm did not return a true value at Makefile.PL line 14. > > > BEGIN failed--compilation aborted at Makefile.PL line 14. > > > ---- > > > Any ideas what this might be? And how I could fix it? > > > > > > > > > Regards > > > Andrea > > > > > > > > > _______________________________________________ > > > radiator mailing list > > > [email protected] > > > http://www.open.com.au/mailman/listinfo/radiator -- Mike McCauley [email protected] Open System Consultants Pty. Ltd 9 Bulbul Place Currumbin Waters QLD 4223 Australia http://www.open.com.au Phone +61 7 5598-7474 Fax +61 7 5598-7070 Radiator: the most portable, flexible and configurable RADIUS server anywhere. SQL, proxy, DBM, files, LDAP, NIS+, password, NT, Emerald, Platypus, Freeside, TACACS+, PAM, external, Active Directory, EAP, TLS, TTLS, PEAP, TNC, WiMAX, RSA, Vasco, Yubikey, MOTP, HOTP, TOTP, DIAMETER etc. Full source on Unix, Windows, MacOSX, Solaris, VMS, NetWare etc. _______________________________________________ radiator mailing list [email protected] http://www.open.com.au/mailman/listinfo/radiator
