Hi Jean-Christophe, Thanks for your contribution. Please run the patch through scripts/checkpatch.pl to check for formatting errors.
On Thu, May 2, 2013 at 5:53 AM, Jean-Christophe DUBOIS <j...@tribudubois.net> wrote: > Signed-off-by: Jean-Christophe DUBOIS <j...@tribudubois.net> > --- > default-configs/arm-softmmu.mak | 2 + > hw/i2c/Makefile.objs | 1 + > hw/i2c/imx_i2c.c | 374 > ++++++++++++++++++++++++++++++++++++++++ > 3 files changed, 377 insertions(+) > create mode 100644 hw/i2c/imx_i2c.c > > diff --git a/default-configs/arm-softmmu.mak b/default-configs/arm-softmmu.mak > index b3a0207..a20f112 100644 > --- a/default-configs/arm-softmmu.mak > +++ b/default-configs/arm-softmmu.mak > @@ -81,3 +81,5 @@ CONFIG_VERSATILE_PCI=y > CONFIG_VERSATILE_I2C=y > > CONFIG_SDHCI=y > + > +CONFIG_IMX_I2C=y > diff --git a/hw/i2c/Makefile.objs b/hw/i2c/Makefile.objs > index 648278e..d27bbaa 100644 > --- a/hw/i2c/Makefile.objs > +++ b/hw/i2c/Makefile.objs > @@ -4,4 +4,5 @@ common-obj-$(CONFIG_ACPI) += smbus_ich9.o > common-obj-$(CONFIG_APM) += pm_smbus.o > common-obj-$(CONFIG_BITBANG_I2C) += bitbang_i2c.o > common-obj-$(CONFIG_EXYNOS4) += exynos4210_i2c.o > +common-obj-$(CONFIG_IMX_I2C) += imx_i2c.o > obj-$(CONFIG_OMAP) += omap_i2c.o > diff --git a/hw/i2c/imx_i2c.c b/hw/i2c/imx_i2c.c > new file mode 100644 > index 0000000..30d3f5c > --- /dev/null > +++ b/hw/i2c/imx_i2c.c > @@ -0,0 +1,374 @@ > +/* > + * i.MX I2C Bus Serial Interface Emulation > + * > + * Copyright (C) 2013 Jean-Christophe Dubois. > + * > + * This program is free software; you can redistribute it and/or modify it > + * under the terms of the GNU General Public License as published by the > + * Free Software Foundation; either version 2 of the License, or > + * (at your option) any later version. > + * > + * This program is distributed in the hope that it will be useful, but > WITHOUT > + * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or > + * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License > + * for more details. > + * > + * You should have received a copy of the GNU General Public License along > + * with this program; if not, see <http://www.gnu.org/licenses/>. > + * > + */ > + > +#include "hw/sysbus.h" > +#include "hw/i2c/i2c.h" > + > +#ifndef IMX_I2C_DEBUG > +#define IMX_I2C_DEBUG 0 > +#endif > + > +#define TYPE_IMX_I2C "imx.i2c" > +#define IMX_I2C(obj) \ > + OBJECT_CHECK(imx_i2c_state, (obj), TYPE_IMX_I2C) > + > +/* i.MX I2C memory map */ > +#define IMX_I2C_MEM_SIZE 0x14 > +#define IADR_ADDR 0x00 /* address register */ > +#define IFDR_ADDR 0x04 /* frequency divider register */ > +#define I2CR_ADDR 0x08 /* control register */ > +#define I2SR_ADDR 0x0c /* status register */ > +#define I2DR_ADDR 0x10 /* data register */ > + > +#define IADR_MASK 0xFE > +#define IADR_RESET 0 > + > +#define IFDR_MASK 0x3F > +#define IFDR_RESET 0 > + > +#define I2CR_IEN (1 << 7) > +#define I2CR_IIEN (1 << 6) > +#define I2CR_MSTA (1 << 5) > +#define I2CR_MTX (1 << 4) > +#define I2CR_TXAK (1 << 3) > +#define I2CR_RSTA (1 << 2) > +#define I2CR_MASK 0xFC > +#define I2CR_RESET 0 > + > +#define I2SR_ICF (1 << 7) > +#define I2SR_IAAF (1 << 6) > +#define I2SR_IBB (1 << 5) > +#define I2SR_IAL (1 << 4) > +#define I2SR_SRW (1 << 2) > +#define I2SR_IIF (1 << 1) > +#define I2SR_RXAK (1 << 0) > +#define I2SR_MASK 0xE9 > +#define I2SR_RESET 0x81 > + > +#define I2DR_MASK 0xFF > +#define I2DR_RESET 0 > + > +#define ADDR_RESET 0xFF00 > + > +#if IMX_I2C_DEBUG > +#define DPRINT(fmt, args...) \ > + do { fprintf(stderr, "%s: "fmt, __func__, ## args); } while (0) > + > +static const char *imx_i2c_get_regname(unsigned offset) > +{ > + switch (offset) { > + case IADR_ADDR: > + return "IADR"; > + case IFDR_ADDR: > + return "IFDR"; > + case I2CR_ADDR: > + return "I2CR"; > + case I2SR_ADDR: > + return "I2SR"; > + case I2DR_ADDR: > + return "I2DR"; > + default: > + return "[?]"; > + } > +} > + > +#else > +#define DPRINT(fmt, args...) do { } while (0) > +#endif > + > +typedef struct imx_i2c_state { > + SysBusDevice busdev; > + MemoryRegion iomem; > + i2c_bus *bus; > + qemu_irq irq; > + > + uint16_t address; > + > + uint16_t iadr; > + uint16_t ifdr; > + uint16_t i2cr; > + uint16_t i2sr; > + uint16_t i2dr_read; > + uint16_t i2dr_write; > +} imx_i2c_state; > + > +static inline bool imx_i2c_is_enabled(imx_i2c_state *s) > +{ > + return (s->i2cr & I2CR_IEN); ERROR: return is not a function, parentheses are not required #148: FILE: hw/i2c/imx_i2c.c:114: + return (s->i2cr & I2CR_IEN); >From checkpatch, here and below. > +} > + > +static inline bool imx_i2c_interrupt_is_enabled(imx_i2c_state *s) > +{ > + return (s->i2cr & I2CR_IIEN); > +} > + > +static inline bool imx_i2c_is_master(imx_i2c_state *s) > +{ > + return (s->i2cr & I2CR_MSTA); > +} > + > +static inline bool imx_i2c_direction_is_tx(imx_i2c_state *s) > +{ > + return (s->i2cr & I2CR_MTX); > +} > + > +static void imx_i2c_reset(DeviceState *d) > +{ > + imx_i2c_state *s = FROM_SYSBUS(imx_i2c_state, SYS_BUS_DEVICE(d)); > + Please don't use FROM_SYSBUS in new code. Use QOM cast macros. http://wiki.qemu.org/QOMConventions Has useful guidelines for the rules around this for new devices. > + if (s->address != ADDR_RESET) { > + i2c_end_transfer(s->bus); > + } > + > + s->address = ADDR_RESET; > + s->iadr = IADR_RESET; > + s->ifdr = IFDR_RESET; > + s->i2cr = I2CR_RESET; > + s->i2sr = I2SR_RESET; > + s->i2dr_read = I2DR_RESET; > + s->i2dr_write = I2DR_RESET; > +} > + > +static inline void imx_i2c_raise_interrupt(imx_i2c_state *s) > +{ > + /* > + * raise an interrupt if the device is enabled and it is configured > + * to generate some interrupts. > + */ > + if (imx_i2c_is_enabled(s) && imx_i2c_interrupt_is_enabled(s)) { > + s->i2sr |= I2SR_IIF; > + qemu_irq_raise(s->irq); > + } > +} > + > +static uint64_t imx_i2c_read(void *opaque, hwaddr offset, > + unsigned size) > +{ > + imx_i2c_state *s = (imx_i2c_state *)opaque; QOM cast macro. > + uint16_t value; > + > + switch (offset) { > + case IADR_ADDR: > + value = s->iadr; > + break; > + case IFDR_ADDR: > + value = s->ifdr; > + break; > + case I2CR_ADDR: > + value = s->i2cr; > + break; > + case I2SR_ADDR: > + value = s->i2sr; > + break; > + case I2DR_ADDR: > + value = s->i2dr_read; > + if (imx_i2c_is_master(s)) { // master mode Do not use C style comments. (Checkpatch picks then up) > + int ret; > + > + if (s->address == ADDR_RESET) { > + // something is wrong as the address is not set > + DPRINT("Trying to read with specifying the slave address\n"); > + } > + > + if ((ret = i2c_recv(s->bus)) >= 0) { > + s->i2dr_read = ret; > + imx_i2c_raise_interrupt(s); > + } else { > + DPRINT("read failed for device 0x%02x\n" s->address); > + s->i2dr_read = 0xff; > + } > + } else { // slave mode > + } Empty else not required. > + break; > + default: > + hw_error("%s: Bad address 0x%x\n", __func__, (int)offset); > + break; > + } > + > + DPRINT("read %s [0x%02x] -> 0x%02x\n", imx_i2c_get_regname(offset), > + (unsigned int)offset, value); > + > + return (uint64_t)value; > +} > + > +static void imx_i2c_write(void *opaque, hwaddr offset, > + uint64_t value, unsigned size) > +{ > + imx_i2c_state *s = (imx_i2c_state *)opaque; > + uint16_t v = value & 0xff; > + > + DPRINT("write %s [0x%02x] <- 0x%02x\n", imx_i2c_get_regname(offset), > + (unsigned int)offset, v); > + > + switch (offset) { > + case IADR_ADDR: > + s->iadr = v & IADR_MASK; > + //i2c_set_slave_address(s->bus, (uint8_t)s->iadr); > + break; > + case IFDR_ADDR: > + s->ifdr = v & IFDR_MASK; > + break; > + case I2CR_ADDR: > + if (imx_i2c_is_enabled(s) && ((v & I2CR_IEN) == 0)) { > + /* This is a soft reset. IADR is preserved during soft resets */ > + uint16_t iadr = s->iadr; > + imx_i2c_reset(&s->busdev.qdev); > + s->iadr = iadr; > + } else { // normal write > + s->i2cr = v & I2CR_MASK; > + > + if (imx_i2c_is_master(s)) { // master mode > + // set the bus to busy > + s->i2sr |= I2SR_IBB; > + } else { // slave mode > + // bus is not busy anymore > + s->i2sr &= ~I2SR_IBB; > + > + // if we unset the master mode then it ends the ongoing > + // transfer if any > + if (s->address != ADDR_RESET) { > + i2c_end_transfer(s->bus); > + s->address = ADDR_RESET; > + } > + } > + > + if (s->i2cr & I2CR_RSTA) { // Restart > + // if this is a restart then it ends the ongoing transfer > + if (s->address != ADDR_RESET) { > + i2c_end_transfer(s->bus); > + s->address = ADDR_RESET; > + s->i2cr &= ~I2CR_RSTA; > + } > + } > + } > + break; > + case I2SR_ADDR: > + /* > + * if the user writes 0 to IIF then lower the interrupt and > + * reset the bit > + */ > + if ((s->i2sr & I2SR_IIF) && !(v & I2SR_IIF)) { > + s->i2sr &= ~I2SR_IIF; > + qemu_irq_lower(s->irq); > + } > + > + /* > + * if the user writes 0 to IAL, reset the bit > + */ > + if ((s->i2sr & I2SR_IAL) && !(v & I2SR_IAL)) { > + s->i2sr &= ~I2SR_IAL; > + /* Nothing more to do ? */ > + } > + > + break; > + case I2DR_ADDR: > + /* if the device is not enabled, nothing to do */ > + if (!imx_i2c_is_enabled(s)) { > + break; > + } > + > + s->i2dr_write = v & I2DR_MASK; > + > + if (imx_i2c_is_master(s)) { // master mode > + /* If this is the first write cycle then it is the slave addr */ > + if (s->address == ADDR_RESET) { > + if (!i2c_start_transfer(s->bus, (uint8_t)s->i2dr_write >> 1, > + (int)s->i2dr_write & 0x01)) { > + // if 0 is returned, the adress is valid > + s->address = s->i2dr_write; > + s->i2sr &= ~I2SR_RXAK; > + imx_i2c_raise_interrupt(s); > + } else { // can't start i2c transaction > + } > + } else { // This is a normal data write > + if (i2c_send(s->bus, s->i2dr_write)) { > + // if the target return non zero then end the transfer > + i2c_end_transfer(s->bus); > + } > + s->i2sr &= ~I2SR_RXAK; > + imx_i2c_raise_interrupt(s); > + } > + } else { // slave mode > + } > + break; > + default: > + hw_error("%s: Bad address 0x%x\n", __func__, (int)offset); > + break; > + } > +} > + > +static const MemoryRegionOps imx_i2c_ops = { > + .read = imx_i2c_read, > + .write = imx_i2c_write, > + .endianness = DEVICE_NATIVE_ENDIAN, I think you may need a .valid definition here as it looks like you have restrictions on access size and alignment? (looks like 4bytes accesses only). > +}; > + > +static const VMStateDescription imx_i2c_vmstate = { > + .name = TYPE_IMX_I2C, > + .version_id = 1, > + .minimum_version_id = 1, > + .fields = (VMStateField[]) { > + VMSTATE_UINT16(address, imx_i2c_state), > + VMSTATE_UINT16(iadr, imx_i2c_state), > + VMSTATE_UINT16(ifdr, imx_i2c_state), > + VMSTATE_UINT16(i2cr, imx_i2c_state), > + VMSTATE_UINT16(i2sr, imx_i2c_state), > + VMSTATE_UINT16(i2dr_read, imx_i2c_state), > + VMSTATE_UINT16(i2dr_write, imx_i2c_state), > + VMSTATE_END_OF_LIST() > + } > +}; > + > +static int imx_i2c_init(SysBusDevice *dev) > +{ Use of the SysBusDeviceClass::init function is deprecated. Please use DeviceClass::realise or Object::init. With no reliance on properties I would suggest this one can be done as just an Object::init fn. Regards, Peter > + imx_i2c_state *s = IMX_I2C(dev); > + > + memory_region_init_io(&s->iomem, &imx_i2c_ops, s, TYPE_IMX_I2C, > + IMX_I2C_MEM_SIZE); > + sysbus_init_mmio(dev, &s->iomem); > + sysbus_init_irq(dev, &s->irq); > + s->bus = i2c_init_bus(&dev->qdev, "i2c"); > + > + return 0; > +} > + > +static void imx_i2c_class_init(ObjectClass *klass, void *data) > +{ > + DeviceClass *dc = DEVICE_CLASS(klass); > + SysBusDeviceClass *sbdc = SYS_BUS_DEVICE_CLASS(klass); > + > + dc->vmsd = &imx_i2c_vmstate; > + dc->reset = imx_i2c_reset; > + sbdc->init = imx_i2c_init; > +} > + > +static const TypeInfo imx_i2c_type_info = { > + .name = TYPE_IMX_I2C, > + .parent = TYPE_SYS_BUS_DEVICE, > + .instance_size = sizeof(imx_i2c_state), > + .class_init = imx_i2c_class_init, > +}; > + > +static void imx_i2c_register_types(void) > +{ > + type_register_static(&imx_i2c_type_info); > +} > + > +type_init(imx_i2c_register_types); > -- > 1.8.1.2 > >
