Signed-off-by: Christoph Heiss <c.he...@proxmox.com>
---
pve-installation.adoc | 126 +-----------------------------------------
1 file changed, 1 insertion(+), 125 deletions(-)
diff --git a/pve-installation.adoc b/pve-installation.adoc
index 2f4642e..0a0dc76 100644
--- a/pve-installation.adoc
+++ b/pve-installation.adoc
@@ -78,131 +78,7 @@ web interface for further configuration.
. Check your xref:chapter_pve_firewall[Firewall settings].
-[[advanced_lvm_options]]
-Advanced LVM Configuration Options
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-
-The installer creates a Volume Group (VG) called `pve`, and additional Logical
-Volumes (LVs) called `root`, `data`, and `swap`, if `ext4` or `xfs` is used. To
-control the size of these volumes use:
-
-`hdsize`::
-
-Defines the total hard disk size to be used. This way you can reserve free
space
-on the hard disk for further partitioning (for example for an additional PV and
-VG on the same hard disk that can be used for LVM storage).
-
-`swapsize`::
-
-Defines the size of the `swap` volume. The default is the size of the installed
-memory, minimum 4 GB and maximum 8 GB. The resulting value cannot be greater
-than `hdsize/8`.
-+
-NOTE: If set to `0`, no `swap` volume will be created.
-
-`maxroot`::
-
-Defines the maximum size of the `root` volume, which stores the operation
-system. The maximum limit of the `root` volume size is `hdsize/4`.
-
-`maxvz`::
-
-Defines the maximum size of the `data` volume. The actual size of the `data`
-volume is:
-+
-`datasize = hdsize - rootsize - swapsize - minfree`
-+
-Where `datasize` cannot be bigger than `maxvz`.
-+
-NOTE: In case of LVM thin, the `data` pool will only be created if `datasize`
is
-bigger than 4GB.
-+
-NOTE: If set to `0`, no `data` volume will be created and the storage
-configuration will be adapted accordingly.
-
-`minfree`::
-
-Defines the amount of free space that should be left in the LVM volume group
-`pve`. With more than 128GB storage available, the default is 16GB, otherwise
-`hdsize/8` will be used.
-+
-NOTE: LVM requires free space in the VG for snapshot creation (not required for
-lvmthin snapshots).
-
-[[advanced_zfs_options]]
-Advanced ZFS Configuration Options
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-The installer creates the ZFS pool `rpool`, if ZFS is used. No swap space is
-created but you can reserve some unpartitioned space on the install disks for
-swap. You can also create a swap zvol after the installation, although this can
-lead to problems (see xref:zfs_swap[ZFS swap notes]).
-
-`ashift`::
-
-Defines the `ashift` value for the created pool. The `ashift` needs to be set
at
-least to the sector-size of the underlying disks (2 to the power of `ashift` is
-the sector-size), or any disk which might be put in the pool (for example the
-replacement of a defective disk).
-
-`compress`::
-
-Defines whether compression is enabled for `rpool`.
-
-`checksum`::
-
-Defines which checksumming algorithm should be used for `rpool`.
-
-`copies`::
-
-Defines the `copies` parameter for `rpool`. Check the `zfs(8)` manpage for the
-semantics, and why this does not replace redundancy on disk-level.
-
-`ARC max size`::
-
-Defines the maximum size the ARC can grow to and thus limits the amount of
-memory ZFS will use. See also the section on
-xref:sysadmin_zfs_limit_memory_usage[how to limit ZFS memory usage] for more
-details.
-
-`hdsize`::
-
-Defines the total hard disk size to be used. This is useful to save free space
-on the hard disk(s) for further partitioning (for example to create a
-swap-partition). `hdsize` is only honored for bootable disks, that is only the
-first disk or mirror for RAID0, RAID1 or RAID10, and all disks in RAID-Z[123].
-
-
-ZFS Performance Tips
-~~~~~~~~~~~~~~~~~~~~
-
-ZFS works best with a lot of memory. If you intend to use ZFS make sure to have
-enough RAM available for it. A good calculation is 4GB plus 1GB RAM for each TB
-RAW disk space.
-
-ZFS can use a dedicated drive as write cache, called the ZFS Intent Log (ZIL).
-Use a fast drive (SSD) for it. It can be added after installation with the
-following command:
-
-----
-# zpool add <pool-name> log </dev/path_to_fast_ssd>
-----
-
-[[nomodeset_kernel_param]]
-Adding the `nomodeset` Kernel Parameter
-~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
-
-Problems may arise on very old or very new hardware due to graphics drivers. If
-the installation hangs during boot, you can try adding the `nomodeset`
-parameter. This prevents the Linux kernel from loading any graphics drivers and
-forces it to continue using the BIOS/UEFI-provided framebuffer.
-
-On the {pve} bootloader menu, navigate to 'Install {pve} (Terminal UI)' and
-press `e` to edit the entry. Using the arrow keys, navigate to the line
starting
-with `linux`, move the cursor to the end of that line and add the
-parameter `nomodeset`, separated by a space from the pre-existing last
-parameter.
-
-Then press `Ctrl-X` or `F10` to boot the configuration.
+include::proxmox-docs-common/partials/advanced-installation.adoc[]
ifndef::wiki[]
--
2.44.0
_______________________________________________
pve-devel mailing list
pve-devel@lists.proxmox.com
https://lists.proxmox.com/cgi-bin/mailman/listinfo/pve-devel
