> http://www.kronjaeger.com/hv/ This guy is nuts... Check out his 300KV supply.
____________ Brian Guralnick [EMAIL PROTECTED] ----- Original Message ----- From: "Tim Exley" <[EMAIL PROTECTED]> To: "'Protel EDA Forum'" <[EMAIL PROTECTED]> Sent: Thursday, January 16, 2003 4:44 PM Subject: Re: [PEDA] SV: High Voltage power supply > As BrianG points out, the answer to your question depends a lot on your > application. Try searching the web for high voltage supplies ... the > following may offer some starting points ... > > http://www.powerdesigners.com/cgibin/design_center/Subject > http://www.kronjaeger.com/hv/ > http://www.high-voltage-assoc.com/cgi-bin/ultimatebb.cgi > http://www.geocities.com/CapeCanaveral/Lab/5322/hv2.html > http://www.epanorama.net/links/psu.html > > > > > -----Original Message----- > From: Brian Guralnick [mailto:[EMAIL PROTECTED]] > Sent: Thursday, 16 January 2003 6:33 p.m. > To: Protel EDA Forum > Subject: Re: [PEDA] SV: High Voltage power supply > > > 8Kv at what current? Pulsed, or continuous? How fast doest it need to > build a charge? I'm thinking along the lines of a small > transformer switched with diode / cap multiplier at the output. Something > similar to an air ionizer circuit. You'll need to use > conformal coating all over your PCB. Will the output be current limited by > a series resistor? > > > ____________ > Brian Guralnick > [EMAIL PROTECTED] > > > ----- Original Message ----- > From: "Peder K. Hellegaard" <[EMAIL PROTECTED]> > To: "Protel EDA Forum" <[EMAIL PROTECTED]> > Sent: Wednesday, January 15, 2003 5:16 PM > Subject: [PEDA] SV: High Voltage power supply > > > > 8kV is needed...... > > > > > > > > -----Oprindelig meddelelse----- > > Fra: Brian Guralnick [mailto:[EMAIL PROTECTED]] > > Sendt: 15. januar 2003 23:03 > > Til: Protel EDA Forum > > Emne: Re: [PEDA] High Voltage power supply > > > > > > How high? > > > > 25Kv, 100Kv? > > > > Or, 600v. > > > > In both cases, a flyback will probably be the cheapest & most cost > > effective. > > > > > > ____________ > > Brian Guralnick > > [EMAIL PROTECTED] > > > > > > ----- Original Message ----- > > From: "Peder K. Hellegaard" <[EMAIL PROTECTED]> > > To: "Protel EDA Forum" <[EMAIL PROTECTED]> > > Sent: Wednesday, January 15, 2003 9:19 AM > > Subject: [PEDA] High Voltage power supply > > > > > > > Anyone who knows where to find schematics for high voltage (low current) > > > power supplies, preferably designed with a series of voltage doublers ? > > > > > > > > > Thanks in advance...... > > > > > > > > > > > > Peter > > > > > > > > > > > > * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * To post a message: mailto:[EMAIL PROTECTED] * * To leave this list visit: * http://www.techservinc.com/protelusers/leave.html * * Contact the list manager: * mailto:[EMAIL PROTECTED] * * Forum Guidelines Rules: * http://www.techservinc.com/protelusers/forumrules.html * * Browse or Search previous postings: * http://www.mail-archive.com/[email protected] * * * * * * * * * * * * * * * * * * * * * * * * * * * * * *
