Thank you. I will try to download the MIB file from this website later, but I have a question. Why does this website not mark the MIB file corresponding to the network device software version? The Huawei network device I use is the same model, but the OID is different in different software versions!
在2024年1月13日星期六 UTC+8 19:30:39<Alexander Wilke> 写道： > Keep in mind that you so Not only need the vendor specific MIBs but you > need in Addition all MIBs which are listet at the to of the MIB as > "IMPORTED". So you maybe need other MIBs in the folder to have the > complete OID path. > > Maybe post: > - Your MIBs folder with the MIBs you use > - The Generator.yml you use > - The Generator command you use. > - The Output of the Generator > > > I Like this Website to Download MIBs and IT tells me the other needed MIBs > as "IMPORTED". I need These MIBs, too in the folder. > > https://www.circitor.fr/Mibs/Html/C/CISCO-IP-IF-MIB.php > > Ben Kochie <[email protected]> schrieb am Sa., 13. Jan. 2024, 11:17: > >> You need to look at your generator output. I'm guessing there were errors. >> >> The HUAWEI-ENTITY-EXTENT-MIB OIDs you listed are in a table, so you can't >> *get* them, you need to *walk* them. When you generate, the output >> should have indexes that need to be used. >> >> You need to make sure your vendor MIBs are added to your MIBDIRS path(s). >> >> The output works just fine when I added your example MIB to a generator >> config. >> >> https://github.com/SuperQ/tools/tree/master/snmp_exporter/huawei >> >> On Sat, Jan 13, 2024 at 10:46 AM Awemnhd <[email protected]> wrote: >> >>> Currently using snmp_exporter version 0.25.0 >>> >>> The problem I had with SNMPv3 has been solved by recompiling >>> generator.yml! >>> >>> However, the if_mib used by default uses the standard SMP management >>> protocol. Some functions on network devices cannot be monitored. You need >>> to add the manufacturer's private MIB OID value to be monitored, for >>> example: >>> get: >>> - 1.3.6.1.4.1.2011.5.25.31.1.1.1.1.5 >>> - 1.3.6.1.4.1.2011.5.25.31.1.1.1.1.7 >>> >>> -name: hwEntityCpuUsage >>> oid: 1.3.6.1.4.1.2011.5.25.31.1.1.1.1.5 >>> type: Integer >>> help: entity CPU usage value range: 0~100 >>> -name: hwEntityMemUsage >>> oid: 1.3.6.1.4.1.2011.5.25.31.1.1.1.1.7 >>> type:Integer >>> help:Machine memory usage, value range: 0~100 >>> >>> I loaded the above configuration section into the generator.yml file and >>> recompiled it. The generated snmp.yml did not have the above configuration >>> section. I manually added it to the compiled snmp.yml file. There was no >>> error message at startup. Check /snmp?target= >>> xx.xxx.xxx.xxx&auth=snmp_v3&module=if_mib, but I can’t see the oid I added >>> get, even if I add the following configuration >>> >>> walk: >>> - 1.3.6.1.4.1.2011.5.25.31 >>> >>> Still can't see it after startup! >>> >>> Final note: I can obtain the above OID values normally using snmpwalk in >>> the same environment. How should I set snmp_exporter correctly? >>> >>> -- >>> You received this message because you are subscribed to the Google >>> Groups "Prometheus Users" group. >>> To unsubscribe from this group and stop receiving emails from it, send >>> an email to [email protected]. >>> To view this discussion on the web visit >>> https://groups.google.com/d/msgid/prometheus-users/9fcf5d63-20ca-45bb-8263-2a6e15302023n%40googlegroups.com >>> >>> <https://groups.google.com/d/msgid/prometheus-users/9fcf5d63-20ca-45bb-8263-2a6e15302023n%40googlegroups.com?utm_medium=email&utm_source=footer> >>> . >>> >> -- >> You received this message because you are subscribed to the Google Groups >> "Prometheus Users" group. >> To unsubscribe from this group and stop receiving emails from it, send an >> email to [email protected]. >> > To view this discussion on the web visit >> https://groups.google.com/d/msgid/prometheus-users/CABbyFmpzoq11NEz5FXkpZgWhts17rW%3DbGVgh%2BDNumzWmDYg%2BPg%40mail.gmail.com >> >> <https://groups.google.com/d/msgid/prometheus-users/CABbyFmpzoq11NEz5FXkpZgWhts17rW%3DbGVgh%2BDNumzWmDYg%2BPg%40mail.gmail.com?utm_medium=email&utm_source=footer> >> . >> > -- You received this message because you are subscribed to the Google Groups "Prometheus Users" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web visit https://groups.google.com/d/msgid/prometheus-users/6f0b3d8d-1c5f-46ad-80fa-15fd6fa49febn%40googlegroups.com.
