I"m trying to compile gpsd and doxygen fails to compile (I think gimp
needs this one too).
The lines leading up to the failure are:
../lib/libdoxygen.a(language.o)(.text+0x2c): In function
`setTranslator(char const*)':
: relocation truncated to fit: R_MIPS_CALL16 qstricmp(char const*, char const*)
../lib/libdoxygen.a(language.o)(.text+0x44): In function
`setTranslator(char const*)':
: relocation truncated to fit: R_MIPS_CALL16 operator new(unsigned long)
../lib/libdoxygen.a(language.o)(.text+0x50): In function
`setTranslator(char const*)':
: relocation truncated to fit: R_MIPS_GOT_DISP vtable for TranslatorEnglish
../lib/libdoxygen.a(language.o)(.text+0x5c): In function
`setTranslator(char const*)':
: relocation truncated to fit: R_MIPS_GOT_DISP theTranslator
../lib/libdoxygen.a(language.o)(.text+0x64): In function
`setTranslator(char const*)':
: relocation truncated to fit: R_MIPS_GOT_DISP theTranslator
../lib/libdoxygen.a(language.o)(.text+0x98): In function
`setTranslator(char const*)':
: relocation truncated to fit: R_MIPS_CALL16 QCString::~QCString()
../lib/libdoxygen.a(language.o)(.text+0xcc): In function
`setTranslator(char const*)':
: relocation truncated to fit: R_MIPS_CALL16 qstricmp(char const*, char const*)
../lib/libdoxygen.a(language.o)(.text+0xe4): In function
`setTranslator(char const*)':
: relocation truncated to fit: R_MIPS_CALL16 operator new(unsigned long)
../lib/libdoxygen.a(language.o)(.text+0xf0): In function
`setTranslator(char const*)':
: relocation truncated to fit: R_MIPS_GOT_DISP vtable for TranslatorDutch
../lib/libdoxygen.a(language.o)(.text+0xfc): In function
`setTranslator(char const*)':
: relocation truncated to fit: R_MIPS_GOT_DISP theTranslator
../lib/libdoxygen.a(language.o)(.text+0x10c): In function
`setTranslator(char const*)':
: additional relocation overflows omitted from the output
collect2: ld returned 1 exit status
gmake[2]: *** [../bin/doxygen] Error 1
gmake[2]: Leaving directory
`/home/ports/pobj/doxygen-1.7.2.src/doxygen-1.7.2/src'
gmake[1]: *** [all] Error 2
gmake[1]: Leaving directory
`/home/ports/pobj/doxygen-1.7.2.src/doxygen-1.7.2/src'
gmake: *** [all] Error 2
*** Error code 2
Stop in /home/ports/devel/doxygen (line 2494 of
/usr/ports/infrastructure/mk/bsd.port.mk).
*** Error code 1
Stop in /home/ports/devel/doxygen (line 2250 of
/usr/ports/infrastructure/mk/bsd.port.mk).
dmesg:
[ using 463944 bytes of bsd ELF symbol table ]
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2011 OpenBSD. All rights reserved. http://www.OpenBSD.org
OpenBSD 5.0 (GENERIC) #26: Wed Aug 17 10:41:08 MDT 2011
[email protected]:/usr/src/sys/arch/loongson/compile/GENERIC
real mem = 1073741824 (1024MB)
avail mem = 1059209216 (1010MB)
mainbus0 at root: Lemote Yeeloong
cpu0 at mainbus0: STC Loongson2F CPU 797 MHz, STC Loongson2F FPU
cpu0: cache L1-I 64KB D 64KB 4 way, L2 512KB 4 way
bonito0 at mainbus0: memory and PCI-X controller, rev 1
pci0 at bonito0 bus 0
rl0 at pci0 dev 7 function 0 "Realtek 8139" rev 0x10: irq 5, address
00:23:8b:84:6f:40
rlphy0 at rl0 phy 0: RTL internal PHY
smfb0 at pci0 dev 8 function 0 "Silicon Motion LynxEM+" rev 0xb0
wsdisplay0 at smfb0 mux 1: console (std, vt100 emulation)
ohci0 at pci0 dev 9 function 0 "NEC USB" rev 0x44: irq 7, version 1.0
ehci0 at pci0 dev 9 function 1 "NEC USB" rev 0x05: irq 7
usb0 at ehci0: USB revision 2.0
uhub0 at usb0 "NEC EHCI root hub" rev 2.00/1.00 addr 1
glxpcib0 at pci0 dev 14 function 0 "AMD CS5536 ISA" rev 0x03: rev 3,
32-bit 3579545Hz timer, watchdog, gpio
gpio1 at glxpcib0: 32 pins
pciide0 at pci0 dev 14 function 2 "AMD CS5536 IDE" rev 0x01: DMA,
channel 0 wired to compatibility, channel 1 wired to compatibility
wd0 at pciide0 channel 0 drive 0: <FUJITSU MHZ2160BH G2>
wd0: 16-sector PIO, LBA48, 152627MB, 312581808 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 2
pciide0: channel 1 ignored (disabled)
auglx0 at pci0 dev 14 function 3 "AMD CS5536 Audio" rev 0x01: isa irq
9, CS5536 AC97
ac97: codec id 0x414c4760 (Avance Logic ALC655 rev 0)
audio0 at auglx0
ohci1 at pci0 dev 14 function 4 "AMD CS5536 USB" rev 0x02: isa irq 11,
version 1.0, legacy support
ehci1 at pci0 dev 14 function 5 "AMD CS5536 USB" rev 0x02: isa irq 11
usb1 at ehci1: USB revision 2.0
uhub1 at usb1 "AMD EHCI root hub" rev 2.00/1.00 addr 1
usb2 at ohci0: USB revision 1.0
uhub2 at usb2 "NEC OHCI root hub" rev 1.00/1.00 addr 1
isa0 at glxpcib0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pms0 at pckbc0 (aux slot)
pckbc0: using irq 12 for aux slot
wsmouse0 at pms0 mux 0
mcclock0 at isa0 port 0x70/2: mc146818 or compatible
ykbec0 at isa0 port 0x381/3
usb3 at ohci1: USB revision 1.0
uhub3 at usb3 "AMD OHCI root hub" rev 1.00/1.00 addr 1
clock0 at mainbus0: ticker on int5 using count register
apm0 at mainbus0
umass0 at uhub1 port 1 configuration 1 interface 0 "Generic
USB2.0-CRW" rev 2.00/58.87 addr 2
umass0: using SCSI over Bulk-Only
scsibus0 at umass0: 2 targets, initiator 0
sd0 at scsibus0 targ 1 lun 0: <Generic-, Multi-Card, 1.00> SCSI0
0/direct removable serial.0bda0158114173400000
urtw0 at uhub1 port 4 "Realtek RTL8187B" rev 2.00/2.00 addr 3
urtw0: RTL8187B rev E, address 00:17:c4:5a:08:1a
vscsi0 at root
scsibus1 at vscsi0: 256 targets
softraid0 at root
scsibus2 at softraid0: 256 targets
pmon bootpath: /dev/disk/wd0
boot device: wd0
root on wd0a swap on wd0b dump on wd0b
WARNING: / was not properly unmounted
ehci_idone: ex=0xc000000000088200 is done!
ehci_idone: ex=0xc000000000088200 is done!
apm0: battery high
urtw1 at uhub1 port 2 "Realtek RTL8187" rev 2.00/1.00 addr 4
urtw1: RTL8187 rev 0x04, RFv2, address 00:c0:ca:1b:c8:fb
