recently I updated my main desktop to -current (base and packages) from
-release (via snapshots) and I noticed problem with esound 0.2.38 (which I
need to use XMMS since my audio device is auich(4), only supporting 48khz
output) where it scratches and stutters a whole lot making most audio
unbearable. I was wondering if anyone else has had similar problems?
Also, esound 0.2.38 doesn't appear to read /etc/esd.conf any longer
(reading only ~/.esd.conf). I managed in a fully-unsupported and hackish
way to get back to 0.2.34 and it works fine so it isn't the hardware or
(as I initially thought) the changes to the kernel audio code recently.
I'm wondering if this is an esound problem (since they presumably don't
test too much on auich with bsd/sun audio over there) or an
openbsd-specific problem. Open to suggestions to fix this in a better
way.
obligatory dmesg:
OpenBSD 4.1-current (GENERIC) #334: Tue Jul 24 12:31:57 MDT 2007
[EMAIL PROTECTED]:/usr/src/sys/arch/i386/compile/GENERIC
cpu0: AMD Sempron(tm) 2200+ ("AuthenticAMD" 686-class, 256KB L2 cache)
1.50 GHz
cpu0:
FPU,V86,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE
real mem = 519598080 (495MB)
avail mem = 494780416 (471MB)
mainbus0 at root
bios0 at mainbus0: AT/286+ BIOS, date 08/19/04, BIOS32 rev. 0 @ 0xfb490,
SMBIOS rev. 2.2 @ 0xf0000 (33 entries)
apm0 at bios0: Power Management spec V1.2
apm0: AC on, battery charge unknown
apm0: flags 70102 dobusy 1 doidle 1
pcibios0 at bios0: rev 2.1 @ 0xf0000/0xdef4
pcibios0: PCI IRQ Routing Table rev 1.0 @ 0xfde60/144 (7 entries)
pcibios0: PCI Exclusive IRQs: 3 5 9 10 11
pcibios0: PCI Interrupt Router at 000:02:0 ("SiS 85C503 System" rev 0x00)
pcibios0: PCI bus #1 is the last bus
bios0: ROM list: 0xc0000/0x8000 0xc8000/0x8000!
cpu0 at mainbus0
pci0 at mainbus0 bus 0: configuration mode 1 (no bios)
pchb0 at pci0 dev 0 function 0 "SiS 741 PCI" rev 0x03
ppb0 at pci0 dev 1 function 0 "SiS 648FX AGP" rev 0x00
pci1 at ppb0 bus 1
vga1 at pci1 dev 0 function 0 "SiS 6330 VGA" rev 0x00: aperture at
0xc0000000, size 0x400000
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
pcib0 at pci0 dev 2 function 0 "SiS 964 ISA" rev 0x36
pciide0 at pci0 dev 2 function 5 "SiS 5513 EIDE" rev 0x01: 741: DMA,
channel 0 configured to compatibility, channel 1 configured to
compatibility
wd0 at pciide0 channel 0 drive 0: <ST3300831A>
wd0: 16-sector PIO, LBA48, 286168MB, 586072368 sectors
wd1 at pciide0 channel 0 drive 1: <ST3120026A>
wd1: 16-sector PIO, LBA48, 114473MB, 234441648 sectors
wd0(pciide0:0:0): using PIO mode 4, Ultra-DMA mode 5
wd1(pciide0:0:1): using PIO mode 4, Ultra-DMA mode 5
atapiscsi0 at pciide0 channel 1 drive 0
scsibus0 at atapiscsi0: 2 targets
cd0 at scsibus0 targ 0 lun 0: <SONY, DVD RW DW-U10A, 1.1d> SCSI0 5/cdrom
removable
cd0(pciide0:1:0): using PIO mode 4, Ultra-DMA mode 2
auich0 at pci0 dev 2 function 7 "SiS 7012 AC97" rev 0xa0: irq 11, SiS7012
AC97
ac97: codec id 0x414c4760 (Avance Logic ALC655 rev 0)
audio0 at auich0
ohci0 at pci0 dev 3 function 0 "SiS 5597/5598 USB" rev 0x0f: irq 5,
version 1.0, legacy support
ohci1 at pci0 dev 3 function 1 "SiS 5597/5598 USB" rev 0x0f: irq 10,
version 1.0, legacy support
ohci2 at pci0 dev 3 function 2 "SiS 5597/5598 USB" rev 0x0f: irq 11,
version 1.0, legacy support
ehci0 at pci0 dev 3 function 3 "SiS 7002 USB" rev 0x00: irq 9
usb0 at ehci0: USB revision 2.0
uhub0 at usb0: SiS EHCI root hub, rev 2.00/1.00, addr 1
sis0 at pci0 dev 4 function 0 "SiS 900 10/100BaseTX" rev 0x91: irq 10,
address 00:11:5b:bd:f2:b9
rlphy0 at sis0 phy 1: RTL8201L 10/100 PHY, rev. 1
"ATI Mach64 GP" rev 0x5c at pci0 dev 9 function 0 not configured
rl0 at pci0 dev 10 function 0 "D-Link Systems 530TX+" rev 0x10: irq 11,
address 00:0d:88:36:2a:d5
rlphy1 at rl0 phy 0: RTL internal PHY
isa0 at pcib0
isadma0 at isa0
pckbc0 at isa0 port 0x60/5
pckbd0 at pckbc0 (kbd slot)
pckbc0: using irq 1 for kbd slot
wskbd0 at pckbd0: console keyboard, using wsdisplay0
pcppi0 at isa0 port 0x61
midi0 at pcppi0: <PC speaker>
spkr0 at pcppi0
lpt0 at isa0 port 0x378/4 irq 7
it0 at isa0 port 0x290/8: IT87
npx0 at isa0 port 0xf0/16: reported by CPUID; using exception 16
pccom0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
fdc0 at isa0 port 0x3f0/6 irq 6 drq 2
usb1 at ohci0: USB revision 1.0
uhub1 at usb1: SiS OHCI root hub, rev 1.00/1.00, addr 1
usb2 at ohci1: USB revision 1.0
uhub2 at usb2: SiS OHCI root hub, rev 1.00/1.00, addr 1
usb3 at ohci2: USB revision 1.0
uhub3 at usb3: SiS OHCI root hub, rev 1.00/1.00, addr 1
biomask ff6d netmask ff6d ttymask ffef
pctr: user-level cycle counter enabled
mtrr: Pentium Pro MTRR support
ulpt0 at uhub3 port 1 configuration 1 interface 0uhidev0 at uhub2 port 1
configuration 1 interface 0
ulpt0: hp deskjet 3600, rev 2.00/1.00, addr 2, iclass 7/1
ulpt0: using bi-directional mode
uhidev0: Mitsumi Electric Apple Optical USB Mouse, rev 1.10/1.08, addr 2,
iclass 3/1
ums0 at uhidev0: 4 buttons and Z dir.
wsmouse0 at ums0 mux 0
dkcsum: wd0 matches BIOS drive 0x80
dkcsum: wd1 matches BIOS drive 0x81
root on wd0a swap on wd0b dump on wd0b
auich0: measured ac97 link rate at 47771 Hz, will use 48000 Hz
