Luc, Thanks for the info. I appreciate your assistance. Alas, as it turns out, PHP compiled, but it doesn't work. :(
I'm going pull out all the guts and start over, using a new compiler, like Studio 10/11. I'll advise you of the results. Thanks! Regards, -Bill -----Original Message----- From: Luc I. Suryo [mailto:[EMAIL PROTECTED] Sent: Tuesday, December 06, 2005 7:18 PM To: Bell, William IT Cc: Luc I. Suryo; Andy Fiddaman; php-install@lists.php.net Subject: Re: [PHP-INSTALL] Trouble running configure on Solaris 9, Apache, MySQL install Hi Bill, > Hey Andy, > I tried again, and it took the 'crle' commands to make it work. The > 'configure' ran successfully this time; no ATTENTION message. Woohoo! > :) > > I kicked off the 'make' and we'll see where that ends up tomorrow > morning (takes a while to run). I've already seen a couple of errors > about "incompatible pointer type" for libiconv, but I'm not making any > predictions (yet). I'll let you know what happens when I get to work > tomorrow morning. > Thanks! > > Hi Luc, > Thanks for the advice. I'm thinking that if this doesn't work, I may > have to go back to the drawing board and try one of your first 2 > suggestions. I should download Studio 10 anyway (while it's free). ;) > > Regarding your 3rd suggestion, when you say "stuff" what do you mean? well let say you have dbm, gd, freetype imap etc support in your php and these depends on other shared library then you will need to adjust your -L and -R to the location of these libs. my php has quite some support buildt in include zlib and i need to make sure it uses my zlib and not sun's ... ;) btw: i believe that Studio 11 is also 'free', and in a 64-bits compilation Sun CC is better then GCC. but that is my opinion... one of the reason I try to avoid GCC is lib_gcc dependancy... we have quite some apache server running php and other (java and such) so to be sure we have a 'clean' depenandcy everything is compiled with Sun C :-) -ls > > > > kinda of a lame solution BUT how about this.... > > recompile everyting with Sun's CC compiler.. > Studio 10 is free for testing... > > or > > get a gcc that is compiled static only (so it has shared > lib_gcc) > > > or > > as the solution From Andy but make sure tiu have the correct > setting the -L and -R MUST point to the lib-directory where you > have install 'stuff' used by apache, php and mysql.. > > just my 25c > > > > > > > On Tue, 6 Dec 2005, Bell, William IT wrote: > > > > ; Thanks Andy, I appreciate the help. I gave it a shot, but > unfortunately > > ; it didn't work. I get the same error in the debug.log output. > > ; > > ; Thanks for trying. Please let me know if you think of anything else > I > > ; can try. > > ; > > ; Regards, > > ; -Bill > > > > Ok, two more options then. Try prefixing your configure command with > an > > LDFLAGS setting like: > > > > LDFLAGS="-L/usr/local/lib -R/usr/local/lib" ./configure ... your usual > > options here... > > > > if that doesn't work, then add /usr/local/lib to your runtime linking > > environment using the following command: > > > > crle -c /var/ld/ld.config -l /usr/lib:/usr/local/lib > > > > If you're using a 64-bit compiler and making a 64-bit binary, you'll > > also need to do: > > > > crle -64 -c /var/ld/64/ld.config -l /usr/lib/64:/usr/local/lib/sparcv9 ******************************************** This communication and any files or attachments transmitted with it may contain information that is confidential, privileged and exempt from disclosure under applicable law. It is intended solely for the use of the individual or the entity to which it is addressed. If you are not the intended recipient, you are hereby notified that any use, dissemination, or copying of this communication is prohibited by federal law. If you have received this communication in error, please destroy it and notify the sender. ********************************************
