Hmm, I don't see anything unusual with these settings files. Is your PLY file unusually large by chance?
Thanks, Cory On Thu, Jul 7, 2016 at 9:46 PM, stephaneンドング メファネ <[email protected]> wrote: > Hello Cory, > > Paraview is still crashing if I start it normally and try to load a .PLY > (even after deleting the settings configuration files, so I am not so sure > the problem is coming from the config files....I don't know...). I am > sending the original config files. > > Stephane > > > 川崎工場 > 火力タービン部 計画設計課 > ンドング-メファネ ステファン > 工学博士 > > 富士電機株式会社 > 〒210-9530川崎市川崎区田辺新田1-1 > TEL 044-329-2155 FAX 044-329-2394 > > On Fri, Jul 8, 2016 at 4:14 AM, Cory Quammen <[email protected]> > wrote: >> >> Hi Sujin, >> >> Thanks for following up. >> >> Stephane, >> >> Could I get the settings configuration files in effect when you saw the >> PLY reader problem to try to figure out which settings caused this problem? >> >> Thanks, >> Cory >> >> On Thu, Jul 7, 2016 at 3:01 PM, Sujin Philip <[email protected]> >> wrote: >>> >>> Hi Cory, >>> >>> We looked into this. The problem was not with the dataset but with the >>> paraview settings files ("paraview -dr" runs without issues). >>> >>> Thanks >>> Sujin >>> >>> >>> On Thu, Jul 7, 2016 at 1:59 PM, Cory Quammen <[email protected]> >>> wrote: >>>> >>>> Hi, >>>> >>>> I can't reproduce this. Do you have an example PLY file you can share >>>> (directly with me if you wish) to try to reproduce the error? >>>> >>>> Thanks, >>>> Cory >>>> >>>> Th >>>> >>>> On Tue, Jun 28, 2016 at 4:24 AM, stephaneンドング メファネ >>>> <[email protected]> wrote: >>>>> >>>>> Hello, >>>>> >>>>> Paraview crashes everytime I try to import a point cloud (.PLY) >>>>> file.The same problem occurs when it is a .PLY file exported from >>>>> Paraview. >>>>> Any idea on how to solve that problem? >>>>> >>>>> Ndong-Mefane Stephane, Dr.Eng >>>>> Basic Design Sec. >>>>> Steam Turbine Dept. >>>>> Kawasaki Factory >>>>> >>>>> Fuji Electric Co., Ltd >>>>> 1-1, Tanabeshinden, Kawasaki-ku, >>>>> Kawasaki-city 210-9530, Japan >>>>> Phone: +81-44-329-2155 >>>>> Fax: +81-44-329-2394 >>>>> >>>>> >>>>> _______________________________________________ >>>>> Powered by www.kitware.com >>>>> >>>>> Visit other Kitware open-source projects at >>>>> http://www.kitware.com/opensource/opensource.html >>>>> >>>>> Please keep messages on-topic and check the ParaView Wiki at: >>>>> http://paraview.org/Wiki/ParaView >>>>> >>>>> Search the list archives at: http://markmail.org/search/?q=ParaView >>>>> >>>>> Follow this link to subscribe/unsubscribe: >>>>> http://public.kitware.com/mailman/listinfo/paraview >>>>> >>>> >>>> >>>> >>>> -- >>>> Cory Quammen >>>> R&D Engineer >>>> Kitware, Inc. >>>> >>>> _______________________________________________ >>>> Powered by www.kitware.com >>>> >>>> Visit other Kitware open-source projects at >>>> http://www.kitware.com/opensource/opensource.html >>>> >>>> Please keep messages on-topic and check the ParaView Wiki at: >>>> http://paraview.org/Wiki/ParaView >>>> >>>> Search the list archives at: http://markmail.org/search/?q=ParaView >>>> >>>> Follow this link to subscribe/unsubscribe: >>>> http://public.kitware.com/mailman/listinfo/paraview >>>> >>> >> >> >> >> -- >> Cory Quammen >> R&D Engineer >> Kitware, Inc. > > -- Cory Quammen R&D Engineer Kitware, Inc. _______________________________________________ Powered by www.kitware.com Visit other Kitware open-source projects at http://www.kitware.com/opensource/opensource.html Please keep messages on-topic and check the ParaView Wiki at: http://paraview.org/Wiki/ParaView Search the list archives at: http://markmail.org/search/?q=ParaView Follow this link to subscribe/unsubscribe: http://public.kitware.com/mailman/listinfo/paraview
