On May 27, 2010, at 11:40 AM, Diego Remolina wrote: > Is there any workaround for this? Perhaps a slightly older version of the > rpms? If so where do I find those?
chkconfig corosync off chkconfig heartbeat on Unfortunately, that's what I had to do on PPC64 RHEL5 > > I cannot get the opensuse-ha rpms any more so I am stuck with a > non-functioning cluster. > > Diego > > Steven Dake wrote: >> This is a known issue on some platforms, although the exact cause is >> unknown. I have tried RHEL 5.5 as well as CentOS 5.5 with clusterrepo rpms >> and been unable to reproduce. I'll keep looking. >> Regards >> -steve >> On 05/27/2010 06:07 AM, Diego Remolina wrote: >>> Hi, >>> >>> I was running the old rpms from the opensuse repo and wanted to change >>> over to the latest packages from the clusterlabs repo in my RHEL 5.5 >>> machines. >>> >>> Steps I took >>> 1. Disabled the old repo >>> 2. Set the nodes to standby (two node drbd cluster) and turned of openais >>> 3. Enabled the new repo. >>> 4. Performed an update with yum -y update which replaced all packages. >>> 5. The configuration file for ais was renamed openais.conf.rpmsave >>> 6. I ran corosync-keygen and copied the key to the second machine >>> 7. I copied the file openais.conf.rpmsave to /etc/corosync/corosync.conf >>> and modified it by removing the service section and moving that to >>> /etc/corosync/service.d/pcmk >>> 8. I copied the configurations to the other machine. >>> 9. When I try to start either openais or corosync with the init scripts >>> I get a failure and nothing that can really point me to an error in the >>> logs. >>> >>> Updated packages: >>> May 26 14:29:32 Updated: cluster-glue-libs-1.0.5-1.el5.x86_64 >>> May 26 14:29:32 Updated: resource-agents-1.0.3-2.el5.x86_64 >>> May 26 14:29:34 Updated: cluster-glue-1.0.5-1.el5.x86_64 >>> May 26 14:29:34 Installed: libibverbs-1.1.3-2.el5.x86_64 >>> May 26 14:29:34 Installed: corosync-1.2.2-1.1.el5.x86_64 >>> May 26 14:29:34 Installed: librdmacm-1.0.10-1.el5.x86_64 >>> May 26 14:29:34 Installed: corosynclib-1.2.2-1.1.el5.x86_64 >>> May 26 14:29:34 Installed: openaislib-1.1.0-2.el5.x86_64 >>> May 26 14:29:34 Updated: openais-1.1.0-2.el5.x86_64 >>> May 26 14:29:34 Installed: libnes-0.9.0-2.el5.x86_64 >>> May 26 14:29:35 Installed: heartbeat-libs-3.0.3-2.el5.x86_64 >>> May 26 14:29:35 Updated: pacemaker-libs-1.0.8-6.1.el5.x86_64 >>> May 26 14:29:36 Updated: heartbeat-3.0.3-2.el5.x86_64 >>> May 26 14:29:36 Updated: pacemaker-1.0.8-6.1.el5.x86_64 >>> >>> Apparently corosync is sec faulting when run from the command line: >>> >>> # /usr/sbin/corosync -f >>> Segmentation fault >>> >>> Any help would be greatly appreciated. >>> >>> Diego >>> >>> >>> >>> _______________________________________________ >>> Pacemaker mailing list: Pacemaker@oss.clusterlabs.org >>> http://oss.clusterlabs.org/mailman/listinfo/pacemaker >>> >>> Project Home: http://www.clusterlabs.org >>> Getting started: http://www.clusterlabs.org/doc/Cluster_from_Scratch.pdf > > _______________________________________________ > Pacemaker mailing list: Pacemaker@oss.clusterlabs.org > http://oss.clusterlabs.org/mailman/listinfo/pacemaker > > Project Home: http://www.clusterlabs.org > Getting started: http://www.clusterlabs.org/doc/Cluster_from_Scratch.pdf _______________________________________________ Pacemaker mailing list: Pacemaker@oss.clusterlabs.org http://oss.clusterlabs.org/mailman/listinfo/pacemaker Project Home: http://www.clusterlabs.org Getting started: http://www.clusterlabs.org/doc/Cluster_from_Scratch.pdf