see in-line
is the device sysupgradeable?
On 2024-11-07 20:59, lotig...@lotigara.ru wrote:
> From: Ivan Davydov <lotig...@lotigara.ru>
>
> Keenetic KN-3211 is a 2.4 Ghz band 11n (Wi-Fi 4) Wi-Fi repeater, based on
> MT7628AN.
>
> Specification:
> - System-On-Chip: MT7628AN
> - CPU/Speed: 575 MHz
> - Flash-Chip: Winbond w25q256
> - Flash size: 32768 KiB
> - RAM: 64 MiB
> - 1x 10/100 Mbps Ethernet
> - 2x external, non-detachable antennas
> - UART (J1) header on PCB (115200 8n1)
> - Wireless No1 (2T2R): SoC Built-in 2.4 GHz 802.11bgn
> - 3x LED, 1x button, 1x mode switch
>
> Notes:
> - The device supports dual boot mode
> - The firmware partitions were concatinated into one
concatenated
> - The status button has been reassigned as the WPS button.
>
> Flash instruction:
> The only way to flash OpenWrt image is to use tftp recovery mode in U-Boot:
>
> 1. Configure PC with static IP 192.168.1.2/24 and tftp server.
> 2. Rename "openwrt-ramips-mt76x8-keenetic_kn-3211-squashfs-factory.bin"
> to "KN-3211.bin" and place it in tftp server directory.
> 3. Connect PC with the ethernet port, press the reset button, power up
> the router and keep button pressed until power led start blinking.
starts
> 4. Router will download file from server, write it to flash and reboot.
>
> Signed-off-by: Ivan Davydov <lotig...@lotigara.ru>
> ---
> .../ramips/dts/mt7628an_keenetic_kn-3211.dts | 218 ++++++++++++++++++
> target/linux/ramips/image/mt76x8.mk | 11 +
> .../mt76x8/base-files/etc/board.d/02_network | 5 +
> 3 files changed, 234 insertions(+)
> create mode 100644 target/linux/ramips/dts/mt7628an_keenetic_kn-3211.dts
>
> diff --git a/target/linux/ramips/dts/mt7628an_keenetic_kn-3211.dts
> b/target/linux/ramips/dts/mt7628an_keenetic_kn-3211.dts
> new file mode 100644
> index 0000000000..a856099ee1
> --- /dev/null
> +++ b/target/linux/ramips/dts/mt7628an_keenetic_kn-3211.dts
> @@ -0,0 +1,218 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> +#include "mt7628an.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/leds/common.h>
> +
indent using tabs
> +/ {
> + compatible = "keenetic,kn-3211", "mediatek,mt7628an-soc";
> + model = "Keenetic KN-3211";
> +
> + aliases {
> + led-boot = &led_status_green;
> + led-failsafe = &led_status_red;
> + led-running = &led_status_green;
> + led-upgrade = &led_status_blue;
> + };
> +
> + chosen {
> + bootargs = "console=ttyS0,115200";
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + led_status_blue: status_blue {
> + function = LED_FUNCTION_STATUS;
> + color = <LED_COLOR_ID_BLUE>;
> + gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
> + };
> +
> + led_status_green: status_green {
> + function = LED_FUNCTION_STATUS;
> + color = <LED_COLOR_ID_GREEN>;
> + gpios = <&gpio 11 GPIO_ACTIVE_HIGH>;
> + };
> +
> + led_status_red: status_red {
> + function = LED_FUNCTION_STATUS;
> + color = <LED_COLOR_ID_RED>;
> + gpios = <&gpio 38 GPIO_ACTIVE_LOW>;
> + };
> + };
> +
> + keys {
> + compatible = "gpio-keys";
> +
> + wps {
> + label = "wps";
> + gpios = <&gpio 37 GPIO_ACTIVE_LOW>;
> + linux,code = <KEY_WPS_BUTTON>;
> + };
> + };
> +
> + virtual_flash {
> + compatible = "mtd-concat";
> + devices = <&firmware1 &firmware2>;
> +
> + partitions {
> + compatible = "fixed-partitions";
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + partition@0 {
> + compatible = "denx,uimage";
> + label = "firmware";
> + reg = <0x0 0x1ec0000>;
> + };
> + };
> + };
> +};
> +
> +&state_default {
> + gpio {
> + groups = "i2s", "i2c", "gpio", "refclk", "wdt", "wled_an";
> + function = "gpio";
> + };
> +};
> +
> +&usbphy {
> + status = "disabled";
> +};
> +
> +&ehci {
> + status = "disabled";
> +};
> +
> +&ohci {
> + status = "disabled";
> +};
> +
> +&spi0 {
> + status = "okay";
> +
> + flash@0 {
> + compatible = "jedec,spi-nor";
> + reg = <0>;
> + spi-max-frequency = <32000000>;
> +
> + partitions {
> + compatible = "fixed-partitions";
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + partition@0 {
> + label = "u-boot";
> + reg = <0x0 0x30000>;
> + read-only;
> + };
> +
> + partition@30000 {
> + label = "u-config";
> + reg = <0x30000 0x10000>;
> + read-only;
> + };
> +
> + partition@40000 {
> + label = "rf-eeprom";
> + reg = <0x40000 0x10000>;
> + read-only;
> +
> + nvmem-layout {
> + compatible = "fixed-layout";
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + eeprom_factory_0: eeprom@0 {
> + reg = <0x0 0x400>;
> + };
> +
> + eeprom_factory_400: eeprom@400 {
> + reg = <0x400 0x4da8>;
> + };
> +
> + macaddr_factory_4: macaddr@4 {
> + reg = <0x4 0x6>;
> + };
> + };
> + };
> +
> + firmware1: partition@50000 {
> + label = "firmware_1";
> + reg = <0x50000 0xf60000>;
> + };
> +
> + partition@fb0000 {
> + label = "config_1";
> + reg = <0xfb0000 0x40000>;
> + read-only;
> + };
> +
> + partition@ff0000 {
> + label = "dump";
> + reg = <0xff0000 0x10000>;
> + read-only;
> + };
> +
> + partition@1000000 {
> + label = "u-state";
> + reg = <0x1000000 0x30000>;
> + read-only;
> + };
> +
> + partition@1030000 {
> + label = "u-config_res";
> + reg = <0x1030000 0x10000>;
> + read-only;
> + };
> +
> + partition@1040000 {
> + label = "rf-eeprom_res";
> + reg = <0x1040000 0x10000>;
> + read-only;
> + };
> +
> + firmware2: partition@1050000 {
> + label = "firmware_2";
> + reg = <0x1050000 0xf60000>;
> + };
> +
> + partition@1fb0000 {
> + label = "config_2";
> + reg = <0x1fb0000 0x40000>;
> + read-only;
> + };
> + };
> + };
> +};
> +
> +ðernet {
> + nvmem-cells = <&macaddr_factory_4>;
> + nvmem-cell-names = "mac-address";
> +};
> +
> +&esw {
> + mediatek,portmap = <0x3e>;
> +};
> +
> +&wmac {
> + status = "okay";
> +
> + nvmem-cells = <&eeprom_factory_0>;
> + nvmem-cell-names = "eeprom";
> +};
> +
> +&pcie {
> + status = "okay";
> +};
> +
> +&pcie0 {
> + wifi@0,0 {
> + compatible = "mediatek,mt76";
> + reg = <0x0000 0 0 0 0>;
> + nvmem-cells = <&eeprom_factory_400>;
> + nvmem-cell-names = "eeprom";
> + ieee80211-freq-limit = <5000000 6000000>;
> + };
> +};
> diff --git a/target/linux/ramips/image/mt76x8.mk
> b/target/linux/ramips/image/mt76x8.mk
> index 8ad840ddfe..96a6ecf5a9 100644
> --- a/target/linux/ramips/image/mt76x8.mk
> +++ b/target/linux/ramips/image/mt76x8.mk
> @@ -365,6 +365,17 @@ define Device/keenetic_kn-1613
> endef
> TARGET_DEVICES += keenetic_kn-1613
>
> +define Device/keenetic_kn-3211
> + IMAGE_SIZE := 31488k
> + DEVICE_VENDOR := Keenetic
> + DEVICE_MODEL := KN-3211
> + DEVICE_PACKAGES := kmod-mt76
> + IMAGES += factory.bin
> + IMAGE/factory.bin := $$(sysupgrade_bin) | pad-to $$$$(BLOCKSIZE) | \
> + check-size | zyimage -d 0x803211 -v "KN-3211"
> +endef
> +TARGET_DEVICES += keenetic_kn-3211
> +
> define Device/kroks_kndrt31r16
> IMAGE_SIZE := 16064k
> DEVICE_VENDOR := Kroks
> diff --git a/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network
> b/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network
> index cb0983b9dc..567f70de6b 100644
> --- a/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network
> +++ b/target/linux/ramips/mt76x8/base-files/etc/board.d/02_network
> @@ -134,6 +134,10 @@ ramips_setup_interfaces()
> ucidef_add_switch "switch0" \
> "1:lan" "2:lan" "3:lan" "0:wan" "6@eth0"
> ;;
> + keenetic,kn-3211)
> + ucidef_add_switch "switch0" \
> + "2:lan" "6@eth0"
> + ;;
> kroks,kndrt31r19)
> ucidef_add_switch "switch0" \
> "0:lan" "6@eth0"
> @@ -277,6 +281,7 @@ ramips_setup_macs()
> totolink,lr1200)
> wan_mac=$(mtd_get_mac_binary factory 0x2e)
> ;;
> + keenetic,kn-3211|\
> keenetic,kn-1613|\
> zyxel,keenetic-extra-ii)
> wan_mac=$(mtd_get_mac_binary rf-eeprom 0x28)
_______________________________________________
openwrt-devel mailing list
openwrt-devel@lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel
