The sender domain has a DMARC Reject/Quarantine policy which disallows
sending mailing list messages using the original "From" header.
To mitigate this problem, the original message has been wrapped
automatically by the mailing list software.
--- Begin Message ---
Moving the fans to hwmon.
After rtl8231 init changes this also will fix
the default fan behaviour.
Update device compat to notify users that their fan
behaviour is about to change.
Signed-off-by: Evan Jobling <evan.jobl...@mslsc.com.au>
---
.../base-files/etc/board.d/03_gpio_switches | 3 ---
.../base-files/etc/board.d/05_compat-version | 17 +++++++++++++++++
.../dts/rtl8380_hpe_1920-8g-poe-180w.dts | 17 +++++++++++++++++
target/linux/realtek/image/rtl838x.mk | 3 +++
4 files changed, 37 insertions(+), 3 deletions(-)
create mode 100644
target/linux/realtek/base-files/etc/board.d/05_compat-version
diff --git a/target/linux/realtek/base-files/etc/board.d/03_gpio_switches
b/target/linux/realtek/base-files/etc/board.d/03_gpio_switches
index 1e49d89c64..9c748396dd 100644
--- a/target/linux/realtek/base-files/etc/board.d/03_gpio_switches
+++ b/target/linux/realtek/base-files/etc/board.d/03_gpio_switches
@@ -6,9 +6,6 @@ board_config_update
board=$(board_name)
case "$board" in
-hpe,1920-8g-poe-180w)
- ucidef_add_gpio_switch "fan_ctrl" "Fan control" "456" "0"
- ;;
esac
board_config_flush
diff --git a/target/linux/realtek/base-files/etc/board.d/05_compat-version
b/target/linux/realtek/base-files/etc/board.d/05_compat-version
new file mode 100644
index 0000000000..6fd4283ca2
--- /dev/null
+++ b/target/linux/realtek/base-files/etc/board.d/05_compat-version
@@ -0,0 +1,17 @@
+# SPDX-License-Identifier: GPL-2.0-or-later
+
+. /lib/functions.sh
+. /lib/functions/uci-defaults.sh
+
+board_config_update
+
+case "$(board_name)" in
+ hpe,1920-8g-poe-180w)
+ ucidef_set_compat_version "1.1"
+ ;;
+esac
+
+board_config_flush
+
+exit 0
+
diff --git a/target/linux/realtek/dts/rtl8380_hpe_1920-8g-poe-180w.dts
b/target/linux/realtek/dts/rtl8380_hpe_1920-8g-poe-180w.dts
index 6398e6d034..2c72cba43f 100644
--- a/target/linux/realtek/dts/rtl8380_hpe_1920-8g-poe-180w.dts
+++ b/target/linux/realtek/dts/rtl8380_hpe_1920-8g-poe-180w.dts
@@ -5,6 +5,23 @@
/ {
compatible = "hpe,1920-8g-poe-180w", "realtek,rtl838x-soc";
model = "HPE 1920-8G-PoE+ 180W (JG922A)";
+
+ gpio_fan_array {
+ compatible = "gpio-fan";
+ target-rpm = <10000>;
+
+ gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>;
+ gpio-fan,speed-map = <5000 0>,
+ <8200 1>;
+
+ alarm-gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
+ #cooling-cells = <2>;
+ };
+};
+
+//set initial GPIO state for fan as it is reset by rtl8231 init.
+&gpio1 {
+ gpio-output-pin-state = <5 1>;
};
&uart1 {
diff --git a/target/linux/realtek/image/rtl838x.mk
b/target/linux/realtek/image/rtl838x.mk
index 01397af931..cea459c4c7 100644
--- a/target/linux/realtek/image/rtl838x.mk
+++ b/target/linux/realtek/image/rtl838x.mk
@@ -123,6 +123,9 @@ define Device/hpe_1920-8g-poe-180w
SOC := rtl8380
DEVICE_MODEL := 1920-8G-PoE+ 180W (JG922A)
DEVICE_PACKAGES += realtek-poe
+ DEVICE_COMPAT_MESSAGE := \
+ Fan control switched to hwmon. Default fan behaviour fixed. Your fans
will run at max speed unless configured otherwise.
+ DEVICE_COMPAT_VERSION := 1.1
H3C_DEVICE_ID := 0x00010025
SUPPORTED_DEVICES += hpe_1920-8g-poe
endef
--
2.39.5
--- End Message ---
_______________________________________________
openwrt-devel mailing list
openwrt-devel@lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel
