W dniu 13.04.2024 o 16:05, Tomasz Maciej Nowak pisze:
> From: Tomasz Maciej Nowak <tmn...@gmail.com>
>
> Dell/SonicWall APL26-0AE (marketed as SonicPoint ACe) is a dual band
> wireless access point.
>
> Specification
> SoC: QualcommAtheros QCA9550
> RAM: 256 MB DDR2
> Flash: 32 MB SPI NOR
> WIFI: 2.4 GHz 3T3R integrated
> 5 GHz 3T3R QCA9890 oversized Mini PCIe card
> Ethernet: 2x 10/100/1000 Mbps QCA8334
> port labeled lan1 is PoE capable (802.3at)
> USB: 1x 2.0
> LEDs: 3x GPIO controlled
Ooops, forgot to update description should be:
LEDs: 6x which 5 are GPIO controlled, an two of them are dual color
Please replace that in the commit message
.
> Buttons: 2x GPIO controlled
> Serial: RJ-45 port, SonicWall pinout
> baud: 115200, parity: none, flow control: none
>
> Before flashing, be sure to have a copy of factory firmware, in case You
> wish to revert to original firmware.
> All described procedures were done in following environment:
> ROM Version: SonicROM (U-Boot) 8.0.0.0-11o
> SafeMode Firmware Version: SonicOS 8.0.0.0-14o
> Firmware Version: SonicOS 9.0.1.0
> In case of other versions, following installation instructions might be
> ineffective.
>
> Installation
> 1. Prepare TFTP server with OpenWrt sysupgrade image and rename that
> image to "sp_fw.bin".
> 2. Connect to one of LAN ports.
> 3. Connect to serial port.
> 4. Hold the reset button (small through hole on side of the unit),
> power on the device and when prompted to stop autoboot, hit any key.
> The held button can now be released.
> 5. Alter U-Boot environment with following commands:
> setenv bootcmd bootm 0x9F510000
> saveenv
> 6. Adjust "ipaddr" (access point) and "serverip" (TFTP server) addresses
> in U-Boot environment, then run following command:
> run lf
> 7. After successful flashing, execute:
> boot
> 8. The access point will boot to OpenWrt. Wait few minutes, until the
> wrench LED will stop blinking, then it's ready for configuration.
>
> Known issues
> Initramfs image can't be bigger than specified kernel size, otherwise
> bootloader will throw LZMA decompressing error. Switching to lzma-loader
> should workaround that.
> This device has Winbond 25Q256FVFG and doesn't have reliable reset, which
> causes hang on reboot, thus broken-flash-reset needs to be added. This
> property addition causes dispaly of "scary" warning on each boot, take
> this warnig into consideration.
>
> Signed-off-by: Tomasz Maciej Nowak <tmn...@gmail.com>
> ---
> package/boot/uboot-envtools/files/ath79 | 3 +
> .../ath79/dts/qca9550_dell_apl26-0ae.dts | 246 ++++++++++++++++++
> .../generic/base-files/etc/board.d/01_leds | 4 +
> .../generic/base-files/etc/board.d/02_network | 4 +
> target/linux/ath79/image/generic.mk | 16 ++
> 5 files changed, 273 insertions(+)
> create mode 100644 target/linux/ath79/dts/qca9550_dell_apl26-0ae.dts
>
> diff --git a/package/boot/uboot-envtools/files/ath79
> b/package/boot/uboot-envtools/files/ath79
> index 567bf9824ddc..2c97e61498e9 100644
> --- a/package/boot/uboot-envtools/files/ath79
> +++ b/package/boot/uboot-envtools/files/ath79
> @@ -117,6 +117,9 @@ buffalo,wzr-hp-g300nh-s|\
> linksys,ea4500-v3)
> ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x20000" "0x20000"
> ;;
> +dell,apl26-0ae)
> + ubootenv_add_uci_config "/dev/mtd1" "0x0" "0x40000" "0x10000"
> + ;;
> domywifi,dw33d)
> ubootenv_add_uci_config "/dev/mtd4" "0x0" "0x10000" "0x10000"
> ;;
> diff --git a/target/linux/ath79/dts/qca9550_dell_apl26-0ae.dts
> b/target/linux/ath79/dts/qca9550_dell_apl26-0ae.dts
> new file mode 100644
> index 000000000000..2f243e027471
> --- /dev/null
> +++ b/target/linux/ath79/dts/qca9550_dell_apl26-0ae.dts
> @@ -0,0 +1,246 @@
> +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/leds/common.h>
> +
> +#include "qca955x.dtsi"
> +
> +/ {
> + model = "Dell SonicPoint ACe (APL26-0AE)";
> + compatible = "dell,apl26-0ae", "qca,qca9550", "qca,qca9558";
> +
> + aliases {
> + label-mac-device = ð0;
> + led-boot = &led_wrench;
> + led-failsafe = &led_wrench;
> + led-upgrade = &led_wrench;
> + };
> +
> + keys {
> + compatible = "gpio-keys";
> +
> + button-reset {
> + label = "reset";
> + gpios = <&gpio 21 GPIO_ACTIVE_LOW>;
> + linux,code = <KEY_RESTART>;
> + };
> +
> + /* Accessible only after disassembling the casing */
> + button-service {
> + label = "service";
> + gpios = <&gpio 22 GPIO_ACTIVE_LOW>;
> + linux,code = <KEY_POWER>;
> + };
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> + pinctrl-names = "default";
> + pinctrl-0 = <&jtag_disable_pins>;
> +
> + led-lan1-amber {
> + color = <LED_COLOR_ID_AMBER>;
> + function = LED_FUNCTION_LAN;
> + function-enumerator = <1>;
> + gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
> + };
> +
> + led-lan1-green {
> + color = <LED_COLOR_ID_GREEN>;
> + function = LED_FUNCTION_LAN;
> + function-enumerator = <1>;
> + gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
> + };
> +
> + led-lan2-amber {
> + color = <LED_COLOR_ID_AMBER>;
> + function = LED_FUNCTION_LAN;
> + function-enumerator = <2>;
> + gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
> + };
> +
> + led-lan2-green {
> + color = <LED_COLOR_ID_GREEN>;
> + function = LED_FUNCTION_LAN;
> + function-enumerator = <2>;
> + gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
> + };
> +
> + led-wlan2g {
> + color = <LED_COLOR_ID_GREEN>;
> + function = LED_FUNCTION_WLAN_2GHZ;
> + linux,default-trigger = "phy1tpt";
> + gpios = <&gpio 1 GPIO_ACTIVE_LOW>;
> + };
> +
> + led-wlan5g {
> + color = <LED_COLOR_ID_GREEN>;
> + function = LED_FUNCTION_WLAN_5GHZ;
> + linux,default-trigger = "phy0tpt";
> + gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
> + };
> +
> + led_wrench: led-wrench {
> + color = <LED_COLOR_ID_AMBER>;
> + function = LED_FUNCTION_STATUS;
> + gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
> + };
> + };
> +};
> +
> +ð0 {
> + status = "okay";
> +
> + nvmem-cells = <&macaddr_sysinfo_50 0>;
> + nvmem-cell-names = "mac-address";
> + phy-handle = <&phy0>;
> + pll-data = <0xa6000000 0x00000101 0x00001616>;
> +};
> +
> +ð1 {
> + status = "okay";
> +
> + nvmem-cells = <&macaddr_sysinfo_50 1>;
> + nvmem-cell-names = "mac-address";
> + pll-data = <0x03000101 0x00000101 0x00001616>;
> +
> + fixed-link {
> + speed = <1000>;
> + full-duplex;
> + };
> +};
> +
> +&mdio0 {
> + status = "okay";
> +
> + phy0: ethernet-phy@0 {
> + reg = <0>;
> +
> + qca,ar8327-initvals = <
> + 0x04 0x07680000 /* PORT0 PAD MODE CTRL */
> + 0x0c 0x00000080 /* PORT6 PAD MODE CTRL */
> + 0x10 0x40000000 /* POWER_ON_STRAP */
> + 0x50 0xffb7c405 /* LED0 CTRL */
> + 0x54 0xffb7c305 /* LED1 CTRL */
> + 0x58 0xffb7c033 /* LED2 CTRL */
> + 0x5c 0x03ffff00 /* LED3 CTRL */
> + 0x7c 0x0000007e /* PORT0_STATUS */
> + 0x94 0x0000007e /* PORT6_STATUS */
> + >;
> + };
> +};
> +
> +&pcie0 {
> + status = "okay";
> +
> + wifi@0,0 {
> + compatible = "qcom,ath10k";
> + reg = <0x0000 0 0 0 0>;
> +
> + /* OEM overwrites EEPROM stored adress and so do we */
> + nvmem-cells = <&macaddr_sysinfo_50 2>;
> + nvmem-cell-names = "mac-address";
> + };
> +};
> +
> +&spi {
> + status = "okay";
> +
> + flash@0 {
> + compatible = "jedec,spi-nor";
> + reg = <0>;
> + spi-max-frequency = <25000000>;
> + broken-flash-reset;
> +
> + partitions {
> + compatible = "fixed-partitions";
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + partition@0 {
> + label = "u-boot";
> + reg = <0x0000000 0x0080000>;
> + read-only;
> + };
> +
> + partition@80000 {
> + label = "u-boot-env";
> + reg = <0x0080000 0x0040000>;
> + };
> +
> + partition@c0000 {
> + label = "sysinfo";
> + reg = <0x00c0000 0x0040000>;
> + read-only;
> +
> + nvmem-layout {
> + compatible = "fixed-layout";
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + macaddr_sysinfo_50: macaddr@50 {
> + compatible = "mac-base";
> + reg = <0x50 0x6>;
> + #nvmem-cell-cells = <1>;
> + };
> + };
> + };
> +
> + partition@100000 {
> + label = "art";
> + reg = <0x0100000 0x0010000>;
> + read-only;
> +
> + nvmem-layout {
> + compatible = "fixed-layout";
> + #address-cells = <1>;
> + #size-cells = <1>;
> +
> + cal_art_1000: calibration@1000 {
> + reg = <0x1000 0x440>;
> + };
> + };
> + };
> +
> + partition@110000 {
> + label = "safemode";
> + reg = <0x0110000 0x0400000>;
> + read-only;
> + };
> +
> + partition@510000 {
> + label = "firmware";
> + reg = <0x0510000 0x1400000>;
> + compatible = "denx,uimage";
> + };
> +
> + partition@1910000 {
> + label = "config";
> + reg = <0x1910000 0x0600000>;
> + read-only;
> + };
> +
> + partition@1f10000 {
> + label = "log";
> + reg = <0x1f10000 0x00f0000>;
> + read-only;
> + };
> + };
> + };
> +};
> +
> +&usb_phy0 {
> + status = "okay";
> +};
> +
> +&usb0 {
> + status = "okay";
> +};
> +
> +&wmac {
> + status = "okay";
> +
> + nvmem-cells = <&macaddr_sysinfo_50 10>, <&cal_art_1000>;
> + nvmem-cell-names = "mac-address", "calibration";
> +};
> diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds
> b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
> index 297485587007..c7da56b780c6 100644
> --- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds
> +++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
> @@ -227,6 +227,10 @@ compex,wpj531-16m)
> ucidef_set_led_rssi "sig3" "SIG3" "green:sig3" "wlan0" "65" "100"
> ucidef_set_led_rssi "sig4" "SIG4" "green:sig4" "wlan0" "50" "100"
> ;;
> +dell,apl26-0ae)
> + ucidef_set_led_switch "lan1" "LAN1" "amber:lan-1" "switch0" "0x04"
> + ucidef_set_led_switch "lan2" "LAN2" "amber:lan-2" "switch0" "0x08"
> + ;;
> devolo,dlan-pro-1200plus-ac|\
> devolo,magic-2-wifi)
> ucidef_set_led_netdev "plcw" "dLAN" "white:dlan" "eth0.1" "rx"
> diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network
> b/target/linux/ath79/generic/base-files/etc/board.d/02_network
> index 6823c333b6e3..2d2385a099ad 100644
> --- a/target/linux/ath79/generic/base-files/etc/board.d/02_network
> +++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network
> @@ -287,6 +287,10 @@ ath79_setup_interfaces()
> ucidef_add_switch "switch0" \
> "1:wan" "5:lan" "6@eth0"
> ;;
> + dell,apl26-0ae)
> + ucidef_add_switch "switch0" \
> + "0@eth0" "2:lan:1" "3:lan:2" "6@eth1"
> + ;;
> devolo,dlan-pro-1200plus-ac|\
> devolo,magic-2-wifi)
> ucidef_add_switch "switch0" \
> diff --git a/target/linux/ath79/image/generic.mk
> b/target/linux/ath79/image/generic.mk
> index 502fdc2ed465..11e25e6afc3b 100644
> --- a/target/linux/ath79/image/generic.mk
> +++ b/target/linux/ath79/image/generic.mk
> @@ -924,6 +924,22 @@ define Device/compex_wpj563
> endef
> TARGET_DEVICES += compex_wpj563
>
> +define Device/dell_apl26-0ae
> + SOC := qca9550
> + DEVICE_VENDOR := Dell
> + DEVICE_MODEL := SonicPoint
> + DEVICE_VARIANT := ACe (APL26-0AE)
> + DEVICE_ALT0_VENDOR := SonicWall
> + DEVICE_ALT0_MODEL := SonicPoint
> + DEVICE_ALT0_VARIANT := ACe (APL26-0AE)
> + DEVICE_PACKAGES := ath10k-firmware-qca988x-ct kmod-ath10k-ct kmod-usb2
> + KERNEL_SIZE := 5952k
> + IMAGE_SIZE := 20480k
> + IMAGE/sysupgrade.bin = append-kernel | pad-to $$$$(BLOCKSIZE) | \
> + append-rootfs | pad-rootfs | check-size | append-metadata
> +endef
> +TARGET_DEVICES += dell_apl26-0ae
> +
> define Device/devolo_dlan-pro-1200plus-ac
> SOC := ar9344
> DEVICE_VENDOR := devolo
--
TMN
_______________________________________________
openwrt-devel mailing list
openwrt-devel@lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel
