Asus RT-AC88U is an AC3100 router featuring 9 Ethernet ports over the integrated Broadcom and the external Realtek switch.
Hardware info: * Processor: Broadcom BCM4709C0KFEBG dual-core @ 1.4 GHz * Switch: BCM53012 in BCM4709C0KFEBG & external RTL8365MB * DDR3 RAM: 512 MB * Flash: 128 MB (ESMT F59L1G81LA-25T) * 2.4GHz: BCM4366 4×4 2.4/5G single chip 802.11ac SoC * 5GHz: BCM4366 4×4 2.4/5G single chip 802.11ac SoC * Ports: 8 Ports, 1 WAN Ports Flashing instructions: * Boot to CFE Recovery Mode by holding the reset button while power-on. * Connect to the router with an ethernet cable. * Set IPv4 address of the computer to 192.168.1.2 subnet 255.255.255.0. * Head to http://192.168.1.1. * Reset NVRAM. * Upload the OpenWrt image. CFE bootloader may reject flashing the image due to image integrity check. In that case, follow the instructions below. * Rename the OpenWrt image as firmware.trx. * Run a TFTP server on the computer and make it serve the firmware.trx file. * Run the URL below on a browser or curl. http://192.168.1.1/do.htm?cmd=flash+-noheader+192.168.1.2:firmware.trx+flash0.trx Signed-off-by: Arınç ÜNAL <arinc.u...@arinc9.com> --- target/linux/bcm53xx/base-files/etc/board.d/01_leds | 6 ++++++ .../linux/bcm53xx/base-files/etc/board.d/02_network | 3 +++ .../bcm53xx/base-files/etc/init.d/set_nvram_vars | 13 +++++++++++++ target/linux/bcm53xx/image/Makefile | 8 ++++++++ 4 files changed, 30 insertions(+) create mode 100755 target/linux/bcm53xx/base-files/etc/init.d/set_nvram_vars diff --git a/target/linux/bcm53xx/base-files/etc/board.d/01_leds b/target/linux/bcm53xx/base-files/etc/board.d/01_leds index aba526b9c349..f37fa79d4f64 100644 --- a/target/linux/bcm53xx/base-files/etc/board.d/01_leds +++ b/target/linux/bcm53xx/base-files/etc/board.d/01_leds @@ -8,6 +8,12 @@ netgear,r8000) ucidef_set_led_usbport "usb2" "USB 2.0" "bcm53xx:white:usb2" "usb1-port2" "usb2-port2" ucidef_set_led_usbport "usb3" "USB 3.0" "bcm53xx:white:usb3" "usb1-port1" "usb2-port1" "usb4-port1" ;; +asus,rt-ac88u) + ucidef_set_led_default "power" "Power" "white:power" "1" + ucidef_set_led_netdev "lan" "LAN" "white:lan" "eth1" + ucidef_set_led_usbport "usb2" "USB 2.0" "white:usb2" "usb1-port2" + ucidef_set_led_usbport "usb3" "USB 3.0" "white:usb3" "usb1-port1" "usb4-port1" + ;; esac board_config_flush diff --git a/target/linux/bcm53xx/base-files/etc/board.d/02_network b/target/linux/bcm53xx/base-files/etc/board.d/02_network index 6d970e1d0e3a..822320c0a6a7 100644 --- a/target/linux/bcm53xx/base-files/etc/board.d/02_network +++ b/target/linux/bcm53xx/base-files/etc/board.d/02_network @@ -13,6 +13,9 @@ bcm53xx_setup_interfaces() asus,rt-ac87u) ucidef_set_interfaces_lan_wan "lan1 lan2 lan3" "wan" ;; + asus,rt-ac88u) + ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4 extsw" "wan" + ;; linksys,panamera) ucidef_set_interfaces_lan_wan "lan1 lan2 lan3 lan4 lan5 lan6 lan7 lan8 extsw" "wan" ;; diff --git a/target/linux/bcm53xx/base-files/etc/init.d/set_nvram_vars b/target/linux/bcm53xx/base-files/etc/init.d/set_nvram_vars new file mode 100755 index 000000000000..9c2b3ebf4de8 --- /dev/null +++ b/target/linux/bcm53xx/base-files/etc/init.d/set_nvram_vars @@ -0,0 +1,13 @@ +#!/bin/sh /etc/rc.common + +START=99 +boot() { + . /lib/functions.sh + + case $(board_name) in + asus,rt-ac88u) + # clear et0macaddr which makes cfe recovery mode inaccessible, set eth1 & eth2 mac addresses and wireless LEDs behaviour variables on nvram + nvram unset et0macaddr set et1macaddr=$(nvram get 0:macaddr) set et2macaddr=$(nvram get 1:macaddr) set 0:ledbh9=0x7 set 1:ledbh9=0x7 && nvram commit + ;; + esac +} diff --git a/target/linux/bcm53xx/image/Makefile b/target/linux/bcm53xx/image/Makefile index cb2643ca5453..afd3380487b8 100644 --- a/target/linux/bcm53xx/image/Makefile +++ b/target/linux/bcm53xx/image/Makefile @@ -167,6 +167,14 @@ define Device/asus_rt-ac87u endef TARGET_DEVICES += asus_rt-ac87u +define Device/asus_rt-ac88u + $(call Device/asus) + DEVICE_MODEL := RT-AC88U + DEVICE_PACKAGES := $(BRCMFMAC_4366C0) $(USB3_PACKAGES) + ASUS_PRODUCTID := RT-AC88U +endef +TARGET_DEVICES += asus_rt-ac88u + define Device/asus_rt-n18u $(call Device/asus) DEVICE_MODEL := RT-N18U -- 2.25.1 _______________________________________________ openwrt-devel mailing list openwrt-devel@lists.openwrt.org https://lists.openwrt.org/mailman/listinfo/openwrt-devel
