Hi, Thanks for the reply, I did not realize that this is for an Omega rather than Omega2+ which is what I have :facepalm:
It looks like there is already support for the omega2+, which is working for me right now. > On 2021/08/22, at 17:25:02 CDT (-05:00), Lech Perczak > <lech.perc...@gmail.com> wrote: > > Hi, > Answer below. > > W dniu 2021-08-22 o 21:29, Mike Bernardo pisze: >> Hi All, >> >> Thanks Jan-Niklas for working on this! I am trying to test this on my onion >> omega2+ (in the arduino dock) .. consoled in via a TTL serial adapter and I >> tried doing a forced sysupgrade to >> openwrt-ath79-generic-onion_omega-squashfs-sysupgrade.bin which I built by >> applying the patch to v21.02.0-rc4 >> (134ac824c5a154edbbe1c581bcbc42d265dc20c0). I tried forcing after sysupgrade >> said that it didn't support omega2p .. now it won't boot, any ideas? Boot >> attempt below. >> >> Note that the below is after I tried flashing >> openwrt-ath79-generic-onion_omega-squashfs-factory.bin via usb (filename >> omega2.bin put on a FAT16 filesystem and you select usb flash in the menu >> after tapping the reset button on powerup. Failing with the same message >> though. >> >> -- >> >> Board: Onion Omega2 APSoC DRAM: 128 MB >> relocate_code Pointer at: 87f60000 >> ****************************** >> Software System Reset Occurred >> ****************************** >> flash manufacture id: c2, device id 20 19 >> find flash: MX25L25635E >> *** Warning - bad CRC, using default environment >> >> ============================================ >> Onion Omega2 UBoot Version: 4.3.0.3 >> -------------------------------------------- >> ASIC 7628_MP (Port5<->None) >> DRAM component: 1024 Mbits DDR, width 16 >> DRAM bus: 16 bit >> Total memory: 128 MBytes >> Flash component: SPI Flash >> Date:Oct 18 2016 Time:17:29:05 >> ============================================ >> icache: sets:512, ways:4, linesz:32 ,total:65536 >> dcache: sets:256, ways:4, linesz:32 ,total:32768 >> CPU freq = 575 MHZ >> Estimated memory size = 128 Mbytes >> Resetting MT7628 PHY. >> Initializing MT7688 GPIO system. >> >> >> ************************************** >> * Hold Reset button for more options * >> ************************************** >> >> >> >> Boot Linux from Flash NO RESET PRESSED. >> ## Booting image at bc050000 ... >> Bad Magic Number,01000000 > > Long story short, you tried loading an image for ath79 architecture (QCA9331 > in this case) on an MT7628 board. You probably need to use U-boot console to > flash correct image for your device over TFTP. >> >> >>> On 2021/08/22, at 07:18:32 CDT (-05:00), Adrian Schmutzler >>> <m...@adrianschmutzler.de> wrote: >>> >>> Hi, >>> >>>> -----Original Message----- >>>> From: openwrt-devel [mailto:openwrt-devel-boun...@lists.openwrt.org] >>>> On Behalf Of Jan-Niklas Burfeind >>>> Sent: Samstag, 14. August 2021 15:55 >>>> To: openwrt-devel@lists.openwrt.org >>>> Cc: open...@sebastianschaper.net; m...@david-bauer.net; Jan-Niklas >>>> Burfeind >>>> Subject: [PATCH v3] ath79: add support for onion omega >>> some inline comments below. >>> >>>> The Onion Omega is a hardware development platform with built-in WiFi. >>>> >>>> https://onioniot.github.io/wiki/ >>>> >>>> Specifications: >>>> - QCA9331 @ 400 MHz (MIPS 24Kc Big-Endian Processor) >>>> - 64MB of DDR2 RAM running at 400 MHz >>>> - 16MB of on-board flash storage >>>> - Support for USB 2.0 >>>> - Support for Ethernet at 100 Mbps >>>> - 802.11b/g/n WiFi at 150 Mbps >>>> - 18 digital GPIOs >>>> - A single Serial UART >>>> - Support for SPI >>>> - Support for I2S >>>> >>>> Flash instructions: >>>> The device is running OpenWrt upon release using the ar71xx target. >>>> Both a sysupgrade >>>> and uploading the factory image using u-boots web-UI do work fine. >>>> >>>> Depending on the ssh client, it might be necessary to enable outdated >>>> KeyExchange methods e.g. in the clients ssh-config: >>>> >>>> Host 192.168.1.1 >>>> KexAlgorithms +diffie-hellman-group1-sha1 >>>> >>>> The stock credentials are: root onioneer >>>> >>>> For u-boots web-UI manually configure `192.168.1.2/24` on your computer, >>>> connect to `192.168.1.1`. >>>> >>>> MAC addresses as verified by OEM firmware: >>>> 2G phy0 label >>>> LAN eth0 label - 1 >>>> >>>> LAN is only available in combination with an optional expansion dock. >>>> >>>> Based on vendor acked commit: >>>> commit 5cd49bb067ca ("ar71xx: add support for Onion Omega") >>>> >>>> Partly reverts: >>>> commit fc553c7e4c8e ("ath79: drop unused/incomplete dts") >>>> >>>> Signed-off-by: Jan-Niklas Burfeind <g...@aiyionpri.me> >>>> --- >>>> kmod-usb-chipidea2 is now included as well as tested; usb devices are now >>>> recognized. >>>> >>>> I added the usb vbus section, like the pisen wmm003n has it and verified >>>> the >>>> gpio looking at the ar71xx commit. >>>> >>>> target/linux/ath79/dts/ar9331_onion_omega.dts | 137 >>>> ++++++++++++++++++ >>>> .../generic/base-files/etc/board.d/02_network | 1 + >>>> target/linux/ath79/image/generic.mk | 13 ++ >>>> 3 files changed, 151 insertions(+) >>>> create mode 100644 target/linux/ath79/dts/ar9331_onion_omega.dts >>>> >>>> diff --git a/target/linux/ath79/dts/ar9331_onion_omega.dts >>>> b/target/linux/ath79/dts/ar9331_onion_omega.dts >>>> new file mode 100644 >>>> index 0000000000..43a0b2f392 >>>> --- /dev/null >>>> +++ b/target/linux/ath79/dts/ar9331_onion_omega.dts >>>> @@ -0,0 +1,137 @@ >>>> +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT >>>> + >>>> +#include <dt-bindings/gpio/gpio.h> >>>> +#include <dt-bindings/input/input.h> >>>> + >>>> +#include "ar9331.dtsi" >>> This include needs to be before the others. >>> >>>> + >>>> +/ { >>>> + model = "Onion Omega"; >>>> + compatible = "onion,omega", "qca,ar9331"; >>>> + >>>> + aliases { >>>> + serial0 = &uart; >>> You could add "label-mac-device = &wmac" here if your commit message is >>> correct. >>> >>>> + led-boot = &led_system; >>>> + led-failsafe = &led_system; >>>> + led-running = &led_system; >>>> + led-upgrade = &led_system; >>>> + }; >>>> + >>>> + leds { >>>> + compatible = "gpio-leds"; >>>> + >>>> + led_system: system { >>>> + label = "amber:system"; >>>> + gpios = <&gpio 27 GPIO_ACTIVE_LOW>; >>>> + }; >>>> + }; >>>> + >>>> + keys { >>>> + compatible = "gpio-keys"; >>>> + poll-interval = <100>; >>> Poll-interval can be dropped with "gpio-keys". >>> >>>> + >>>> + reset { >>>> + label = "reset"; >>>> + linux,code = <KEY_RESTART>; >>>> + gpios = <&gpio 11 GPIO_ACTIVE_HIGH>; >>>> + debounce-interval = <60>; >>>> + }; >>>> + }; >>>> + >>>> + reg_usb_vbus: reg_usb_vbus { >>>> + compatible = "regulator-fixed"; >>>> + regulator-name = "usb_vbus"; >>>> + regulator-min-microvolt = <5000000>; >>>> + regulator-max-microvolt = <5000000>; >>>> + gpio = <&gpio 8 GPIO_ACTIVE_HIGH>; >>>> + enable-active-high; >>>> + }; >>>> +}; >>>> + >>>> +&ref { >>>> + clock-frequency = <25000000>; >>>> +}; >>>> + >>>> +&gpio { >>>> + status = "okay"; >>>> +}; >>> gpio is enabled by default, this block can be dropped. >>> >>>> + >>>> +&usb { >>>> + status = "okay"; >>>> + >>>> + vbus-supply = <®_usb_vbus>; >>>> + dr_mode = "host"; >>>> +}; >>>> + >>>> +&usb_phy { >>>> + status = "okay"; >>>> +}; >>>> + >>>> +ð0 { >>>> + status = "okay"; >>>> + >>>> + compatible = "syscon", "simple-mfd"; >>>> +}; >>>> + >>>> +ð1 { >>>> + status = "okay"; >>>> + >>>> + nvmem-cells = <&macaddr_uboot_1fc00>; >>>> + nvmem-cell-names = "mac-address"; >>>> + mac-address-increment = <(-1)>; >>>> + >>>> + gmac-config { >>>> + device = <&gmac>; >>>> + switch-phy-addr-swap = <4>; >>>> + switch-phy-swap = <4>; >>>> + }; >>>> +}; >>>> + >>>> +&spi { >>>> + status = "okay"; >>>> + >>>> + flash@0 { >>>> + compatible = "jedec,spi-nor"; >>>> + spi-max-frequency = <25000000>; >>>> + reg = <0>; >>>> + >>>> + partitions { >>>> + compatible = "fixed-partitions"; >>>> + #address-cells = <1>; >>>> + #size-cells = <1>; >>>> + >>>> + uboot: partition@0 { >>>> + label = "u-boot"; >>>> + reg = <0x000000 0x020000>; >>>> + read-only; >>>> + compatible = "nvmem-cells"; >>>> + #address-cells = <1>; >>>> + #size-cells = <1>; >>>> + >>>> + macaddr_uboot_1fc00: macaddr@1fc00 { >>>> + reg = <0x1fc00 0x6>; >>>> + }; >>>> + }; >>> It's common practice at the moment to put a separate block for defining the >>> MAC addresses at the end of the file. >>> Please do so, just look at any other DTS file in recent master. >>> >>>> + >>>> + partition@20000 { >>>> + compatible = "tplink,firmware"; >>>> + label = "firmware"; >>>> + reg = <0x020000 0xfd0000>; >>>> + }; >>>> + >>>> + art: partition@ff0000 { >>>> + label = "art"; >>>> + reg = <0xff0000 0x010000>; >>>> + read-only; >>>> + }; >>>> + }; >>>> + }; >>>> +}; >>>> + >>>> +&wmac { >>>> + status = "okay"; >>>> + >>>> + mtd-cal-data = <&art 0x1000>; >>> I personally prefer an empty line after mtd-cal-data. >>> >>> Best >>> >>> Adrian >>> >>>> + nvmem-cells = <&macaddr_uboot_1fc00>; >>>> + nvmem-cell-names = "mac-address"; >>>> +}; >>>> diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network >>>> b/target/linux/ath79/generic/base-files/etc/board.d/02_network >>>> index 4fe7fbc027..b859c64633 100644 >>>> --- a/target/linux/ath79/generic/base-files/etc/board.d/02_network >>>> +++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network >>>> @@ -45,6 +45,7 @@ ath79_setup_interfaces() >>>> netgear,ex7300|\ >>>> ocedo,koala|\ >>>> ocedo,raccoon|\ >>>> + onion,omega|\ >>>> openmesh,mr600-v1|\ >>>> openmesh,mr600-v2|\ >>>> openmesh,mr900-v1|\ >>>> diff --git a/target/linux/ath79/image/generic.mk >>>> b/target/linux/ath79/image/generic.mk >>>> index 2abe1b7307..6e9ff01cc0 100644 >>>> --- a/target/linux/ath79/image/generic.mk >>>> +++ b/target/linux/ath79/image/generic.mk >>>> @@ -1653,6 +1653,19 @@ define Device/ocedo_ursus endef >>>> TARGET_DEVICES += ocedo_ursus >>>> >>>> +define Device/onion_omega >>>> + $(Device/tplink-16mlzma) >>>> + SOC := ar9331 >>>> + DEVICE_VENDOR := Onion >>>> + DEVICE_MODEL := Omega >>>> + DEVICE_PACKAGES := kmod-usb-chipidea2 >>>> + SUPPORTED_DEVICES += onion-omega >>>> + KERNEL_INITRAMFS := kernel-bin | append-dtb | lzma | uImage lzma >>>> + IMAGE_SIZE := 16192k >>>> + TPLINK_HWID := 0x04700001 >>>> +endef >>>> +TARGET_DEVICES += onion_omega >>>> + >>>> define Device/openmesh_common_64k >>>> DEVICE_VENDOR := OpenMesh >>>> DEVICE_PACKAGES := uboot-envtools >>>> -- >>>> 2.32.0 >>>> >>>> >>>> _______________________________________________ >>>> openwrt-devel mailing list >>>> openwrt-devel@lists.openwrt.org >>>> https://lists.openwrt.org/mailman/listinfo/openwrt-devel >>> _______________________________________________ >>> openwrt-devel mailing list >>> openwrt-devel@lists.openwrt.org >>> https://lists.openwrt.org/mailman/listinfo/openwrt-devel >> >> _______________________________________________ >> openwrt-devel mailing list >> openwrt-devel@lists.openwrt.org >> https://lists.openwrt.org/mailman/listinfo/openwrt-devel > > > -- > Pozdrawiam, > Lech Perczak > lech.perc...@gmail.com > Mobile: +48 694 309 185 > > > _______________________________________________ > openwrt-devel mailing list > openwrt-devel@lists.openwrt.org > https://lists.openwrt.org/mailman/listinfo/openwrt-devel _______________________________________________ openwrt-devel mailing list openwrt-devel@lists.openwrt.org https://lists.openwrt.org/mailman/listinfo/openwrt-devel
