Hi, > >> Notes: > >> > >> - there is no way to configure the correct MAC address for secondary phy > >> (5GHz) on MT7615D > > This one seems to address a similar case (just scroll to the very bottom): > > > > https://patchwork.ozlabs.org/project/openwrt/patch/1607939702-85475- > 1- > > git-send-email-xinfa.d...@gl-inet.com/ > > > > Would this work for you as well (at least for the MAC address)? > > > > Best > > > > Adrian > > I've tested it, but doesn't work. > > I made the following change,
sorry, but would you test again please with the 10_fix_wifi_mac changes and
recent master?
There have been several changes to mt76 in
b837534f029da10abbd1069392867e0700134ace that might be relevant/helping.
Best
Adrian
>
> ```
>
> diff --git
> a/target/linux/ramips/mt7621/base-
> files/etc/hotplug.d/ieee80211/10_fix_wifi_mac
> b/target/linux/ramips/mt7621/base-
> files/etc/hotplug.d/ieee80211/10_fix_wifi_mac
> index b7a41f038c..f0093d4337 100644
> ---
> a/target/linux/ramips/mt7621/base-
> files/etc/hotplug.d/ieee80211/10_fix_wifi_mac
> +++
> b/target/linux/ramips/mt7621/base-
> files/etc/hotplug.d/ieee80211/10_fix_wifi_mac
> @@ -10,6 +10,14 @@ PHYNBR=${DEVPATH##*/phy}
> board=$(board_name)
>
> case "$board" in
> + elecom,wrc-1167gs2-b)
> + [ "$PHYNBR" = "1" ] && \
> + $(mtd_get_mac_binary factory 0x4) >
> /sys${DEVPATH}/macaddress
> + ;;
> + elecom,wrc-1167gst2)
> + [ "$PHYNBR" = "1" ] && \
> + macaddr_add $(mtd_get_mac_binary factory
> 0xe006) 2 > /sys${DEVPATH}/macaddress
> + ;;
> linksys,ea7300-v1|\
> linksys,ea7300-v2|\
> linksys,ea7500-v2)
>
> ```
>
> but iwinfo still reports the MAC address generated from phy0 by mt76
>
> driver.
>
> ```
>
> (WRC-1167GS2-B)
>
> root@OpenWrt:/# iwinfo
> wlan0 ESSID: unknown
> Access Point: 04:AB:18:58:2F:15
> Mode: Client Channel: unknown (unknown)
> Tx-Power: 3 dBm Link Quality: unknown/70
> Signal: unknown Noise: unknown
> Bit Rate: unknown
> Encryption: unknown
> Type: nl80211 HW Mode(s): 802.11bgnac
> Hardware: 14C3:7615 7615:14C3 [MediaTek MT7615E]
> TX power offset: none
> Frequency offset: none
> Supports VAPs: yes PHY name: phy0
>
> wlan1 ESSID: unknown
> Access Point: 86:AB:18:58:2F:15
> Mode: Client Channel: unknown (unknown)
> Tx-Power: 3 dBm Link Quality: unknown/70
> Signal: unknown Noise: unknown
> Bit Rate: unknown
> Encryption: unknown
> Type: nl80211 HW Mode(s): 802.11nac
> Hardware: 14C3:7615 7615:14C3 [MediaTek MT7615E]
> TX power offset: none
> Frequency offset: none
> Supports VAPs: yes PHY name: phy1
>
> root@OpenWrt:/# cat /sys/class/ieee80211/phy1/macaddress
> 86:ab:18:58:2f:15
>
> ```
>
> >> - Wi-Fi band on primary phy (2.4GHz) cannot be limitted by specifying
> >> ieee80211-freq-limit
> >> (fail to register secondary phy due to error)
> >> - mtd-mac-address in the wifi node is required for using
> >> mtd-mac-address-increment
> >>
> >> Signed-off-by: INAGAKI Hiroshi <musashino.o...@gmail.com>
> >> ---
> >> .../dts/mt7621_elecom_wrc-1167gs2-b.dts | 57 ++++++
> >> .../dts/mt7621_elecom_wrc-1167gsxx.dtsi | 179
> ++++++++++++++++++
> >> target/linux/ramips/image/mt7621.mk | 8 +
> >> 3 files changed, 244 insertions(+)
> >> create mode 100644
> >> target/linux/ramips/dts/mt7621_elecom_wrc-1167gs2-
> >> b.dts
> >> create mode 100644 target/linux/ramips/dts/mt7621_elecom_wrc-
> >> 1167gsxx.dtsi
> >>
> >> diff --git a/target/linux/ramips/dts/mt7621_elecom_wrc-1167gs2-b.dts
> >> b/target/linux/ramips/dts/mt7621_elecom_wrc-1167gs2-b.dts
> >> new file mode 100644
> >> index 0000000000..af0c580c64
> >> --- /dev/null
> >> +++ b/target/linux/ramips/dts/mt7621_elecom_wrc-1167gs2-b.dts
> >> @@ -0,0 +1,57 @@
> >> +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> >> +
> >> +#include "mt7621_elecom_wrc-1167gsxx.dtsi"
> >> +
> >> +/ {
> >> + compatible = "elecom,wrc-1167gs2-b", "mediatek,mt7621-soc";
> >> + model = "ELECOM WRC-1167GS2-B";
> >> +
> >> + aliases {
> >> + label-mac-device = &wan;
> >> + };
> >> +};
> >> +
> >> +&gmac0 {
> >> + mtd-mac-address = <&factory 0xfff4>; };
> >> +
> >> +&wan {
> >> + mtd-mac-address = <&factory 0xfffa>; };
> >> +
> >> +&partitions {
> >> + partition@50000 {
> >> + compatible = "denx,uimage";
> >> + label = "firmware";
> >> + reg = <0x50000 0xb00000>;
> >> + };
> >> +
> >> + partition@b50000 {
> >> + label = "tm_pattern";
> >> + reg = <0xb50000 0x380000>;
> >> + read-only;
> >> + };
> >> +
> >> + partition@ed0000 {
> >> + label = "tm_key";
> >> + reg = <0xed0000 0x80000>;
> >> + read-only;
> >> + };
> >> +
> >> + partition@f50000 {
> >> + label = "nvram";
> >> + reg = <0xf50000 0x30000>;
> >> + read-only;
> >> + };
> >> +
> >> + partition@f80000 {
> >> + label = "user_data";
> >> + reg = <0xf80000 0x80000>;
> >> + read-only;
> >> + };
> >> +};
> >> +
> >> +&wifi {
> >> + mtd-mac-address = <&factory 0x4>;
> >> + mtd-mac-address-increment = <(-1)>; };
> >> diff --git a/target/linux/ramips/dts/mt7621_elecom_wrc-1167gsxx.dtsi
> >> b/target/linux/ramips/dts/mt7621_elecom_wrc-1167gsxx.dtsi
> >> new file mode 100644
> >> index 0000000000..a13ddc963f
> >> --- /dev/null
> >> +++ b/target/linux/ramips/dts/mt7621_elecom_wrc-1167gsxx.dtsi
> >> @@ -0,0 +1,179 @@
> >> +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> >> +
> >> +#include "mt7621.dtsi"
> >> +
> >> +#include <dt-bindings/gpio/gpio.h>
> >> +#include <dt-bindings/input/input.h>
> >> +
> >> +/ {
> >> + aliases {
> >> + led-boot = &led_power_green;
> >> + led-failsafe = &led_power_green;
> >> + led-running = &led_power_green;
> >> + led-upgrade = &led_power_green;
> >> + };
> >> +
> >> + leds {
> >> + compatible = "gpio-leds";
> >> +
> >> + wlan2g {
> >> + label = "white:wlan2g";
> >> + gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
> >> + };
> >> +
> >> + wlan5g {
> >> + label = "white:wlan5g";
> >> + gpios = <&gpio 4 GPIO_ACTIVE_LOW>;
> >> + };
> >> +
> >> + led_power_green: power_green {
> >> + label = "green:power";
> >> + gpios = <&gpio 7 GPIO_ACTIVE_HIGH>;
> >> + };
> >> +
> >> + power_blue {
> >> + label = "blue:power";
> >> + gpios = <&gpio 8 GPIO_ACTIVE_HIGH>;
> >> + };
> >> +
> >> + wps {
> >> + label = "red:wps";
> >> + gpios = <&gpio 15 GPIO_ACTIVE_HIGH>;
> >> + };
> >> +
> >> + power_red {
> >> + label = "red:power";
> >> + gpios = <&gpio 16 GPIO_ACTIVE_HIGH>;
> >> + };
> >> + };
> >> +
> >> + keys {
> >> + compatible = "gpio-keys";
> >> +
> >> + reset {
> >> + label = "reset";
> >> + gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
> >> + linux,code = <KEY_RESTART>;
> >> + };
> >> +
> >> + wps {
> >> + label = "wps";
> >> + gpios = <&gpio 18 GPIO_ACTIVE_LOW>;
> >> + linux,code = <KEY_WPS_BUTTON>;
> >> + };
> >> +
> >> + client {
> >> + label = "client";
> >> + gpios = <&gpio 41 GPIO_ACTIVE_LOW>;
> >> + linux,code = <BTN_0>;
> >> + linux,input-type = <EV_SW>;
> >> + };
> >> +
> >> + ap {
> >> + label = "ap";
> >> + gpios = <&gpio 42 GPIO_ACTIVE_LOW>;
> >> + linux,code = <BTN_0>;
> >> + linux,input-type = <EV_SW>;
> >> + };
> >> +
> >> + extender {
> >> + label = "extender";
> >> + gpios = <&gpio 43 GPIO_ACTIVE_LOW>;
> >> + linux,code = <BTN_0>;
> >> + linux,input-type = <EV_SW>;
> >> + };
> >> +
> >> + router {
> >> + label = "router";
> >> + gpios = <&gpio 44 GPIO_ACTIVE_LOW>;
> >> + linux,code = <BTN_0>;
> >> + linux,input-type = <EV_SW>;
> >> + };
> >> + };
> >> +};
> >> +
> >> +&switch0 {
> >> + ports {
> >> + wan: port@0 {
> >> + status = "okay";
> >> + label = "wan";
> >> + };
> >> +
> >> + port@1 {
> >> + status = "okay";
> >> + label = "lan4";
> >> + };
> >> +
> >> + port@2 {
> >> + status = "okay";
> >> + label = "lan3";
> >> + };
> >> +
> >> + port@3 {
> >> + status = "okay";
> >> + label = "lan2";
> >> + };
> >> +
> >> + port@4 {
> >> + status = "okay";
> >> + label = "lan1";
> >> + };
> >> + };
> >> +};
> >> +
> >> +&spi0 {
> >> + status = "okay";
> >> +
> >> + flash@0 {
> >> + compatible = "jedec,spi-nor";
> >> + reg = <0>;
> >> + spi-max-frequency = <40000000>;
> >> +
> >> + partitions: partitions {
> >> + compatible = "fixed-partitions";
> >> + #address-cells = <1>;
> >> + #size-cells = <1>;
> >> +
> >> + partition@0 {
> >> + label = "u-boot";
> >> + reg = <0x0 0x30000>;
> >> + read-only;
> >> + };
> >> +
> >> + partition@30000 {
> >> + label = "u-boot-env";
> >> + reg = <0x30000 0x10000>;
> >> + read-only;
> >> + };
> >> +
> >> + factory: partition@40000 {
> >> + label = "factory";
> >> + reg = <0x40000 0x10000>;
> >> + read-only;
> >> + };
> >> + };
> >> + };
> >> +};
> >> +
> >> +&pcie {
> >> + status = "okay";
> >> +};
> >> +
> >> +&pcie0 {
> >> + wifi: wifi@0,0 {
> >> + compatible = "mediatek,mt76";
> >> + reg = <0x0000 0 0 0 0>;
> >> + mediatek,mtd-eeprom = <&factory 0x0>;
> >> + };
> >> +};
> >> +
> >> +&state_default {
> >> + gpio {
> >> + groups = "i2c", "uart3", "jtag", "wdt", "sdhci";
> >> + function = "gpio";
> >> + };
> >> +};
> >> +
> >> +&xhci {
> >> + status = "disabled";
> >> +};
> >> diff --git a/target/linux/ramips/image/mt7621.mk
> >> b/target/linux/ramips/image/mt7621.mk
> >> index ce9a3ae3d2..468c6ad4da 100644
> >> --- a/target/linux/ramips/image/mt7621.mk
> >> +++ b/target/linux/ramips/image/mt7621.mk
> >> @@ -404,6 +404,14 @@ define Device/elecom_wrc-gs
> >> DEVICE_PACKAGES := kmod-mt7615e kmod-mt7615-firmware endef
> >>
> >> +define Device/elecom_wrc-1167gs2-b
> >> + $(Device/elecom_wrc-gs)
> >> + IMAGE_SIZE := 11264k
> >> + DEVICE_MODEL := WRC-1167GS2-B
> >> + ELECOM_HWNAME := WRC-1167GS2
> >> +endef
> >> +TARGET_DEVICES += elecom_wrc-1167gs2-b
> >> +
> >> define Device/elecom_wrc-1750gs
> >> $(Device/elecom_wrc-gs)
> >> IMAGE_SIZE := 11264k
> >> --
> >> 2.28.0.windows.1
> >>
> >>
> >> _______________________________________________
> >> openwrt-devel mailing list
> >> openwrt-devel@lists.openwrt.org
> >> https://lists.openwrt.org/mailman/listinfo/openwrt-devel
>
> _______________________________________________
> openwrt-devel mailing list
> openwrt-devel@lists.openwrt.org
> https://lists.openwrt.org/mailman/listinfo/openwrt-devel
openpgp-digital-signature.asc
Description: PGP signature
_______________________________________________ openwrt-devel mailing list openwrt-devel@lists.openwrt.org https://lists.openwrt.org/mailman/listinfo/openwrt-devel
