Hi, > -----Original Message----- > From: openwrt-devel [mailto:openwrt-devel-boun...@lists.openwrt.org] > On Behalf Of Russell Senior > Sent: Mittwoch, 16. Dezember 2020 12:01 > To: openwrt-devel@lists.openwrt.org > Subject: [PATCHv2] ath79: Add support for Ubiquiti Bullet AC > > > CPU: Atheros AR9342 rev 3 SoC > RAM: 64 MB DDR2 > Flash: 16 MB NOR SPI > WLAN 2.4GHz: Atheros AR9342 v3 (ath9k) > WLAN 5.0GHz: QCA988X > Ports: 1x GbE > > Flashing procedure is identical to other ubnt devices. > https://openwrt.org/toh/ubiquiti/common > > Flashing through factory firmware > 1. Ensure firmware version v8.7.0 is installed. > Up/downgrade to this exact version. > 2. Patch fwupdate.real binary using > `hexdump -Cv /bin/ubntbox | sed 's/14 40 fe 27/00 00 00 00/g' | \ > hexdump -R > /tmp/fwupdate.real` > 3. Make the patched fwupdate.real binary executable using > `chmod +x /tmp/fwupdate.real` > 4. Copy the squashfs factory image to /tmp on the device 5. Flash OpenWrt > using `/tmp/fwupdate.real -m <squashfs-factory image>` 6. Wait for the > device to reboot (copied from Ubiquiti NanoBeam AC and modified) > > Flashing from serial console > 1. Connect serial console (115200 baud) > 2. Connect ethernet to a network with a TFTP server, through a > passive PoE injector. > 3. Press a key to obtain a u-boot prompt 4. Set your TFTP server's ip address, > with: > setenv serverip <tftp-server-address> 5. Set the Bullet AC's ip address, > with: > setenv ipaddr <bullet-ac-address> > 6. Set the boot file, with: > setenv bootfile <name-of-initramfs-binary-on-tftp-server> > 7. Fetch the binary with tftp: > tftpboot > 8. Boot the initramfs binary: > bootm > 9. From the initramfs, fetch the sysupgrade binary, and flash it with > sysupgrade. > > Phy0 is QCA988X which can tune either band (2.4 or 5GHz). Phy1 is AR9342, > on which 5GHz is disabled. It isn't currently known whether phy1 is routed to > the N connector at all. > > Signed-off-by: Russell Senior <russ...@personaltelco.net> > --- > v2: > - Make "Flashing through factory firmware" instructions actually work by > changing UBNT_TYPE to 2WA > --- > .../linux/ath79/dts/ar9342_ubnt_bullet-ac.dts | 38 +++++++++++++++++++ > .../generic/base-files/etc/board.d/01_leds | 1 + > .../generic/base-files/etc/board.d/02_network | 1 + > .../etc/hotplug.d/firmware/11-ath10k-caldata | 1 + > target/linux/ath79/image/generic-ubnt.mk | 17 +++++++++ > 5 files changed, 58 insertions(+) > create mode 100644 target/linux/ath79/dts/ar9342_ubnt_bullet-ac.dts > > diff --git a/target/linux/ath79/dts/ar9342_ubnt_bullet-ac.dts > b/target/linux/ath79/dts/ar9342_ubnt_bullet-ac.dts > new file mode 100644 > index 0000000000..be0b0792bb > --- /dev/null > +++ b/target/linux/ath79/dts/ar9342_ubnt_bullet-ac.dts > @@ -0,0 +1,38 @@ > +// SPDX-License-Identifier: GPL-2.0-only > + > +#include "ar9342_ubnt_wa_1port.dtsi" > + > +/ { > + compatible = "ubnt,bullet-ac", "ubnt,wa", "qca,ar9342"; > + model = "Ubiquiti Bullet AC (2WA)";
would you provide some details about that odd "2WA"?
> +
> + aliases {
> + led-boot = &led_rssi3;
> + led-failsafe = &led_rssi3;
> + led-upgrade = &led_rssi3;
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + rssi0 {
> + label = "blue:rssi0";
> + gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
> + };
> +
> + rssi1 {
> + label = "blue:rssi1";
> + gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
> + };
> +
> + rssi2 {
> + label = "blue:rssi2";
> + gpios = <&gpio 13 GPIO_ACTIVE_LOW>;
> + };
> +
> + led_rssi3: rssi3 {
> + label = "blue:rssi3";
> + gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
> + };
> + };
> +};
> diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds
> b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
> index a0ed21e318..46d4650eac 100755
> --- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds
> +++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds
> @@ -366,6 +366,7 @@ ubnt,rocket-m)
> ucidef_set_led_rssi "rssimediumhigh" "RSSIMEDIUMHIGH"
> "green:link3" "wlan0" "51" "100"
> ucidef_set_led_rssi "rssihigh" "RSSIHIGH" "green:link4" "wlan0" "76"
> "100"
> ;;
> +ubnt,bullet-ac|\
This requires to move the block to keep sorting.
> ubnt,nanobeam-ac|\
> ubnt,nanobeam-ac-gen2|\
> ubnt,nanostation-ac|\
> diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network
> b/target/linux/ath79/generic/base-files/etc/board.d/02_network
> index 905848a2ba..9293e5522b 100755
> --- a/target/linux/ath79/generic/base-files/etc/board.d/02_network
> +++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network
> @@ -58,6 +58,7 @@ ath79_setup_interfaces()
> tplink,re450-v2|\
> tplink,re450-v3|\
> tplink,tl-wr902ac-v1|\
> + ubnt,bullet-ac|\
> ubnt,bullet-m-ar7240|\
> ubnt,bullet-m-ar7241|\
> ubnt,bullet-m-xw|\
> diff --git a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-
> ath10k-caldata b/target/linux/ath79/generic/base-
> files/etc/hotplug.d/firmware/11-ath10k-caldata
> index 0d09cd3140..be62e52480 100644
> --- a/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-
> ath10k-caldata
> +++ b/target/linux/ath79/generic/base-files/etc/hotplug.d/firmware/11-at
> +++ h10k-caldata
> @@ -26,6 +26,7 @@ case "$FIRMWARE" in
> qxwlan,e1700ac-v2-16m|\
> qxwlan,e600gac-v2-8m|\
> qxwlan,e600gac-v2-16m|\
> + ubnt,bullet-ac|\
> ubnt,unifiac-lite|\
> ubnt,unifiac-lr|\
> ubnt,unifiac-mesh|\
> diff --git a/target/linux/ath79/image/generic-ubnt.mk
> b/target/linux/ath79/image/generic-ubnt.mk
> index c347bd1cf1..4c34aa5dfa 100644
> --- a/target/linux/ath79/image/generic-ubnt.mk
> +++ b/target/linux/ath79/image/generic-ubnt.mk
> @@ -67,6 +67,16 @@ define Device/ubnt-sw
> KERNEL := kernel-bin | append-dtb | relocate-kernel | lzma | uImage lzma
> endef
>
> +define Device/ubnt-2wa
Strictly, the would need to be moved as well. But I'm not sure whether I insist
here.
Best
Adrian
> + $(Device/ubnt)
> + SOC := ar9342
> + IMAGE_SIZE := 15744k
> + UBNT_BOARD := WA
> + UBNT_CHIP := ar934x
> + UBNT_TYPE := 2WA
> + UBNT_VERSION := 8.5.3
> +endef
> +
> define Device/ubnt-wa
> $(Device/ubnt)
> SOC := ar9342
> @@ -131,6 +141,13 @@ define Device/ubnt_airrouter endef
> TARGET_DEVICES += ubnt_airrouter
>
> +define Device/ubnt_bullet-ac
> + $(Device/ubnt-2wa)
> + DEVICE_MODEL := Bullet AC
> + DEVICE_PACKAGES += kmod-ath10k-ct-smallbuffers
> +ath10k-firmware-qca988x-ct rssileds endef TARGET_DEVICES +=
> +ubnt_bullet-ac
> +
> define Device/ubnt_bullet-m-ar7240
> $(Device/ubnt-xm)
> SOC := ar7240
> --
> 2.29.2
>
>
>
> --
> Russell Senior, President
> russ...@personaltelco.net
>
> _______________________________________________
> openwrt-devel mailing list
> openwrt-devel@lists.openwrt.org
> https://lists.openwrt.org/mailman/listinfo/openwrt-devel
openpgp-digital-signature.asc
Description: PGP signature
_______________________________________________ openwrt-devel mailing list openwrt-devel@lists.openwrt.org https://lists.openwrt.org/mailman/listinfo/openwrt-devel
