The Teltonika RUT955 is an industrial 2G/3G/4G WiFi router with
various additional inputs and outputs.
Specification:
- 550/400/200 MHz (CPU/DDR/AHB)
- 128 MB of RAM (DDR2)
- 16 MB of FLASH (SPI NOR)
- 4x 10/100 Mbps Ethernet, with passive PoE support on LAN1
- 2T2R 2,4 GHz (AR9344)
- built-in 3G module (example: Qutectel EC-25EU)
- RS232 on D-Sub9 port (Cypress ACM via USB, /dev/ttyACM0)
- RS422/RS485 (AR934x high speed UART, /dev/ttyATH1)
- analog 0-9V input (MCP3221)
- various digital inputs and outputs incl. a relay
- 2x miniSIM slot (can be swapped via GPIO)
- 2x RP-SMA/F (Wi-Fi), 2x SMA/F (3G), 1x GPS
- 2x 74HC595 shift registers providing 16 GPOs
- 12x LED (4 are driven by AR9344, 7 by 74HC595)
- 1x button (reset)
- DC jack for main power input (9-30 V)
- debugging UART available on PCB edge connector
Serial console (/dev/ttyS0) pinout:
- RX: pin1 (square) on top side of the main PCB (AR9344 is on top)
- TX: pin1 (square) on bottom side
Flash instruction:
Vendor firmware is based on OpenWrt CC release. Use the "factory" image
directly in GUI (make sure to uncheck "keep settings") or in U-Boot web
based recovery. To avoid any problems, make sure to first update vendor
firmware to latest version - "factory" image was successfully tested on
device running "RUT9XX_R_00.06.051" firmware and U-Boot "3.0.2".
Signed-off-by: Daniel Golle <dan...@makrotopia.org>
---
target/linux/ath79/dts/ar9344_tlt_rut955.dts | 301 ++++++++++++++++++
.../generic/base-files/etc/board.d/02_network | 5 +
target/linux/ath79/image/generic.mk | 37 +++
3 files changed, 343 insertions(+)
create mode 100644 target/linux/ath79/dts/ar9344_tlt_rut955.dts
diff --git a/target/linux/ath79/dts/ar9344_tlt_rut955.dts
b/target/linux/ath79/dts/ar9344_tlt_rut955.dts
new file mode 100644
index 0000000000..06d18f8d26
--- /dev/null
+++ b/target/linux/ath79/dts/ar9344_tlt_rut955.dts
@@ -0,0 +1,301 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "ar9344.dtsi"
+
+/ {
+ model = "Teltonika RUT955";
+ compatible = "tlt,rut955", "qca,ar9344";
+
+ aliases {
+ serial0 = &uart;
+ serial1 = &hs_uart;
+ led-boot = &led_system_green;
+ led-failsafe = &led_system_red;
+ led-running = &led_system_green;
+ led-upgrade = &led_system_red;
+ label-mac-device = ð1;
+ };
+
+ i2c {
+ compatible = "i2c-gpio";
+ scl-gpios = <&gpio 16 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+ sda-gpios = <&gpio 17 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ hwmon@4d {
+ compatible = "microchip,mcp3221";
+ reg = <0x4d>;
+ };
+ };
+
+ gpio_ext_spi {
+ compatible = "spi-gpio";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmx_led_spi_gpio>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ sck-gpios = <&gpio 4 GPIO_ACTIVE_HIGH>; // 74HC595 SRCLK
(Serial Clock)
+ mosi-gpios = <&gpio 12 GPIO_ACTIVE_HIGH>; // 74HC595 SER
(Serial)
+ cs-gpios = <&gpio 20 GPIO_ACTIVE_HIGH>; // 74HC595 RCLK
(Register Clock)
+ num-chipselects = <1>;
+
+ gpio_ext: gpio_ext@0 {
+ compatible = "fairchild,74hc595";
+ reg = <0>;
+ gpio-controller;
+ #gpio-cells = <2>;
+ registers-number = <2>;
+ spi-max-frequency = <10000000>;
+ gpio-line-names = "signal_bar0", "signal_bar1",
"signal_bar2", "signal_bar3",
+ "signal_bar4", "status_red", "status_green",
"sim_sel",
+ "", "relay", "modem_vbus", "modem_rst",
+ "", "", "", "";
+ };
+ };
+
+ reg_usb_modem_vbus: reg_usb_modem_vbus {
+ compatible = "regulator-fixed";
+ regulator-name = "usb_modem_vbus";
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ gpio = <&gpio_ext 10 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+ regulator-always-on;
+ regulator-boot-on;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ signal0 {
+ label = "rut955:green:signal1";
+ gpios = <&gpio_ext 0 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+
+ signal1 {
+ label = "rut955:green:signal2";
+ gpios = <&gpio_ext 1 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+
+ signal2 {
+ label = "rut955:green:signal3";
+ gpios = <&gpio_ext 2 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+
+ signal3 {
+ label = "rut955:green:signal4";
+ gpios = <&gpio_ext 3 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+
+ signal4 {
+ label = "rut955:green:signal5";
+ gpios = <&gpio_ext 4 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+
+ led_system_red: systemred {
+ label = "rut955:green:red";
+ gpios = <&gpio_ext 5 GPIO_ACTIVE_HIGH>;
+ default-state = "off";
+ };
+
+ led_system_green: systemgreen {
+ label = "rut955:green:system";
+ gpios = <&gpio_ext 6 GPIO_ACTIVE_HIGH>;
+ default-state = "on";
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys";
+
+ reset {
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio 15 GPIO_ACTIVE_HIGH>;
+ debounce-interval = <60>;
+ };
+ };
+};
+
+&gpio {
+ gpio-line-names = "", "wan_led", "input", "mmc_cs",
+ "leds_sck", "", "", "",
+ "", "", "", "",
+ "leds_mosi", "lan2_led", "lan1_led", "",
+ "i2c_scl", "i2c_sda", "", "DIN2",
+ "spi?", "DIN1", "lan3_led";
+};
+
+&ref {
+ clock-frequency = <40000000>;
+};
+
+&uart {
+ status = "okay";
+};
+
+&hs_uart {
+ status = "okay";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmx_uart2>;
+};
+
+&spi {
+ cs-gpios = <0>, <0>;
+ num-cs = <2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&jtag_disable_pins>, <&pmx_spi_cs1>;
+
+ status = "okay";
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <25000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x0 0x20000>;
+ read-only;
+ };
+
+ config: partition@20000 {
+ label = "config";
+ reg = <0x20000 0x10000>;
+ read-only;
+ };
+
+ art: partition@30000 {
+ label = "art";
+ reg = <0x30000 0x10000>;
+ read-only;
+ };
+
+ partition@40000 {
+ label = "firmware";
+ reg = <0x40000 0xf30000>;
+ compatible = "tplink,firmware";
+ };
+
+ partition@f70000 {
+ label = "event-log";
+ reg = <0xf70000 0x80000>;
+ };
+ };
+ };
+
+ microsd@1 {
+ compatible = "mmc-spi-slot";
+ spi-max-frequency = <25000000>;
+ reg = <1>;
+ voltage-ranges = <3200 3400>;
+ broken-cd;
+ status = "disabled";
+ };
+};
+
+&usb {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ status = "okay";
+
+ port@1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ reg = <1>;
+
+ hub_port1: port@1 { // user USB port
+ compatible = "usb-a-connector";
+ reg = <1>;
+ };
+
+ hub_port2: port@2 { // N/C
+ reg = <2>;
+ };
+
+ hub_port3: port@3 { // Cypress CDC-ACM serial (RS-232 D-Sub9)
+ reg = <3>;
+ };
+
+ hub_port4: port@4 { // Quectel EC-25 modem
+ reg = <4>;
+ vbus-supply = <®_usb_modem_vbus>;
+ };
+ };
+};
+
+&usb_phy {
+ status = "okay";
+};
+
+&wmac {
+ status = "okay";
+
+ mtd-cal-data = <&art 0x1000>;
+ mtd-mac-address = <&config 0x0>;
+ mtd-mac-address-increment = <2>;
+};
+
+ð1 {
+ status = "okay";
+
+ mtd-mac-address = <&config 0x0>;
+
+ gmac-config {
+ device = <&gmac>;
+ switch-phy-swap = <0>;
+ switch-only-mode = <1>;
+ };
+};
+
+ð0 {
+ status = "okay";
+
+ phy-handle = <&swphy4>;
+
+ mtd-mac-address = <&config 0x0>;
+ mtd-mac-address-increment = <1>;
+};
+
+&builtin_switch {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pmx_leds_switch>;
+};
+
+&pinmux {
+ pmx_spi_cs1: pinmux_spi_cs1 {
+ pinctrl-single,bits = <0x0 0x07000000 0xff000000>;
+ };
+
+ pmx_led_spi_gpio: pinmux_led_spi_gpio {
+ pinctrl-single,bits = <0x4 0x0 0xff>,
+ <0xc 0x0 0xff>,
+ <0x14 0x0 0xff>;
+ };
+
+ pmx_leds_switch: pinmux_leds_switch {
+ pinctrl-single,bits = <0x0 0x00002d00 0x0000ff00>,
+ <0xc 0x002c2b00 0x00ffff00>,
+ <0x14 0x002a0000 0x00ff0000>;
+ };
+
+ pmx_uart2: pinmux_uart2 {
+ pinctrl-single,bits = <0x10 0x4f000000 0xff000000>,
+ <0x3c 0x000b0000 0x00ff0000>;
+ };
+};
diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network
b/target/linux/ath79/generic/base-files/etc/board.d/02_network
index 4630cf8447..4b75dc0359 100755
--- a/target/linux/ath79/generic/base-files/etc/board.d/02_network
+++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network
@@ -210,6 +210,11 @@ ath79_setup_interfaces()
ucidef_add_switch "switch0" \
"0@eth0" "1:lan" "2:lan" "3:wan"
;;
+ tlt,rut955)
+ ucidef_set_interface_wan "eth1"
+ ucidef_add_switch "switch0" \
+ "0@eth0" "2:lan:3" "3:lan:2" "4:lan:1"
+ ;;
tplink,archer-a7-v5|\
tplink,archer-c6-v2|\
tplink,archer-c6-v2-us|\
diff --git a/target/linux/ath79/image/generic.mk
b/target/linux/ath79/image/generic.mk
index 1bc7b2d68e..ab11120da8 100644
--- a/target/linux/ath79/image/generic.mk
+++ b/target/linux/ath79/image/generic.mk
@@ -36,6 +36,11 @@ define Build/addpattern
-mv "$@.new" "$@"
endef
+define Build/append-md5sum-bin
+ $(STAGING_DIR_HOST)/bin/mkhash md5 $@ | sed 's/../\\\\x&/g' |\
+ xargs echo -ne >> $@
+endef
+
define Build/cybertan-trx
@echo -n '' > $@-empty.bin
-$(STAGING_DIR_HOST)/bin/trx -o $@.new \
@@ -73,6 +78,17 @@ define Build/pisen_wmb001n-factory
rm -rf "$@.tmp"
endef
+define Build/teltonika-fw-fake-checksum
+ # Teltonika U-Boot web based firmware upgrade/recovery routine compares
+ # 16 bytes from md5sum1[16] field in TP-Link v1 header (offset: 76 bytes
+ # from begin of the firmware file) with 16 bytes stored just before
+ # 0xdeadc0de marker. Values are only compared, MD5 sum is not verified.
+ let \
+ offs="$$(stat -c%s $@) - 20"; \
+ dd if=$@ bs=1 count=16 skip=76 |\
+ dd of=$@ bs=1 count=16 seek=$$offs conv=notrunc
+endef
+
define Device/seama
KERNEL := kernel-bin | append-dtb | relocate-kernel | lzma
KERNEL_INITRAMFS := $$(KERNEL) | seama
@@ -1044,6 +1060,27 @@ define Device/sitecom_wlr-7100
endef
TARGET_DEVICES += sitecom_wlr-7100
+define Device/tlt_rut955
+ SOC := ar9344
+ DEVICE_TITLE := Teltonika RUT955
+ DEVICE_PACKAGES := kmod-usb2 kmod-usb-acm kmod-usb-net-qmi-wwan
kmod-usb-serial-option kmod-hwmon-mcp3021 uqmi -uboot-envtools
+ IMAGE_SIZE := 15552k
+ TPLINK_HWID := 0x35000001
+ TPLINK_HWREV := 0x1
+ TPLINK_HEADER_VERSION := 1
+ KERNEL := kernel-bin | append-dtb | lzma | tplink-v1-header
+ KERNEL_INITRAMFS := kernel-bin | append-dtb | lzma | uImage lzma
+ IMAGES := sysupgrade.bin factory.bin
+ IMAGE/factory.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | append-rootfs
|\
+ pad-rootfs | teltonika-fw-fake-checksum | append-string master |\
+ append-md5sum-bin | check-size $$$$(IMAGE_SIZE)
+ IMAGE/sysupgrade.bin := append-kernel | pad-to $$$$(BLOCKSIZE) |\
+ append-rootfs | pad-rootfs | append-metadata |\
+ check-size $$$$(IMAGE_SIZE)
+ SUPPORTED_DEVICES += rut900
+endef
+TARGET_DEVICES += tlt_rut955
+
define Device/trendnet_tew-823dru
SOC := qca9558
DEVICE_VENDOR := Trendnet
--
2.25.0
_______________________________________________
openwrt-devel mailing list
openwrt-devel@lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel
