From: Pavel Balan <ad...@kryma.net> This patch adds support for the COMFAST CF-E130N v2, an outdoor wireless CPE with a single Ethernet port and a 802.11bgn radio.
Specifications: - QCA9531 SoC - 1x 10/100 Mbps Ethernet with PoE-in support - 64 MB of RAM (DDR2) - 16 MB of FLASH - 5 dBi built-in antenna - POWER/LAN/WLAN green LEDs - 4x RSSI LEDs (2x red, 2x green) - UART (115200 8N1) and GPIO (J9) headers on PCB Flashing instructions: The original firmware is based on OpenWrt so a sysupgrade image can be installed via the stock web GUI. The U-boot bootloader also contains a backup TFTP client to upload the firmware from. Upon boot, it checks its ethernet network for the IP 192.168.1.10. Host a TFTP server and provide the image to be flashed as file firmware_auto.bin. Signed-off-by: Pavel Balan <ad...@kryma.net> --- Run-tested on hardware. Changes since v3: -Formatting fixes -Made steps towards disabling the non-existent eth0 port Responses to Adrian's questions: -Re unused led: the led is blocked by a mostly opaque plate in the shell. It can still be controlled, though. -Re verifying addresses: I don't think I did. How would I do that? --- .../ath79/dts/qca9531_comfast_cf-e130n-v2.dts | 143 ++++++++++++++++++ .../generic/base-files/etc/board.d/01_leds | 9 ++ .../generic/base-files/etc/board.d/02_network | 2 + target/linux/ath79/image/generic.mk | 10 ++ 4 files changed, 164 insertions(+) create mode 100644 target/linux/ath79/dts/qca9531_comfast_cf-e130n-v2.dts diff --git a/target/linux/ath79/dts/qca9531_comfast_cf-e130n-v2.dts b/target/linux/ath79/dts/qca9531_comfast_cf-e130n-v2.dts new file mode 100644 index 0000000000..1f5326c9d8 --- /dev/null +++ b/target/linux/ath79/dts/qca9531_comfast_cf-e130n-v2.dts @@ -0,0 +1,143 @@ +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> + +#include "qca953x.dtsi" + +/ { + compatible = "comfast,cf-e130n-v2", "qca,qca9531"; + model = "COMFAST CF-E130N v2"; + + aliases { + serial0 = &uart; + led-boot = &led_rssihigh; + led-failsafe = &led_rssihigh; + led-upgrade = &led_rssihigh; + label-mac-device = ð1; + }; + + leds { + compatible = "gpio-leds"; + + pinctrl-names = "default"; + + wlan { + label = "cf-e130n-v2:green:wlan"; + gpios = <&gpio 0 GPIO_ACTIVE_LOW>; + linux,default-trigger = "phy0tpt"; + }; + + lan { + label = "cf-e130n-v2:green:lan"; + gpios = <&gpio 2 GPIO_ACTIVE_LOW>; + }; + + unused { + label = "cf-e130n-v2:green:unused"; + gpios = <&gpio 3 GPIO_ACTIVE_LOW>; + }; + + rssilow { + label = "cf-e130n-v2:red:rssilow"; + gpios = <&gpio 11 GPIO_ACTIVE_LOW>; + }; + + rssimediumlow { + label = "cf-e130n-v2:red:rssimediumlow"; + gpios = <&gpio 12 GPIO_ACTIVE_LOW>; + }; + + rssimediumhigh { + label = "cf-e130n-v2:green:rssimediumhigh"; + gpios = <&gpio 14 GPIO_ACTIVE_LOW>; + }; + + led_rssihigh: rssihigh { + label = "cf-e130n-v2:green:rssihigh"; + gpios = <&gpio 16 GPIO_ACTIVE_LOW>; + }; + }; + + keys { + compatible = "gpio-keys"; + + reset { + label = "reset"; + linux,code = <KEY_RESTART>; + gpios = <&gpio 17 GPIO_ACTIVE_LOW>; + debounce-interval = <60>; + }; + }; +}; + +&spi { + status = "okay"; + + num-cs = <1>; + + flash@0 { + compatible = "jedec,spi-nor"; + reg = <0>; + spi-max-frequency = <25000000>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "u-boot"; + reg = <0x000000 0x010000>; + read-only; + }; + + art: partition@10000 { + label = "art"; + reg = <0x010000 0x010000>; + read-only; + }; + + partition@20000 { + compatible = "denx,uimage"; + label = "firmware"; + reg = <0x020000 0x7d0000>; + }; + + partition@7f0000 { + label = "nvram"; + reg = <0x7f0000 0x010000>; + read-only; + }; + }; + }; +}; + +&uart { + status = "okay"; + +}; + +ð1 { + status = "okay"; + + phy-handle = <&swphy0>; + + mtd-mac-address = <&art 0x0>; + + gmac-config { + device = <&gmac>; + switch-phy-swap = <1>; + }; +}; + +ð0 { + compatible = "syscon", "simple-mfd"; +}; + +&wmac { + status = "okay"; + + mtd-cal-data = <&art 0x1000>; +}; diff --git a/target/linux/ath79/generic/base-files/etc/board.d/01_leds b/target/linux/ath79/generic/base-files/etc/board.d/01_leds index fbb0d0ea03..7521e435a1 100755 --- a/target/linux/ath79/generic/base-files/etc/board.d/01_leds +++ b/target/linux/ath79/generic/base-files/etc/board.d/01_leds @@ -47,6 +47,15 @@ comfast,cf-e120a-v3) ucidef_set_led_rssi "rssimediumhigh" "RSSIMEDIUMHIGH" "$boardname:green:rssimediumhigh" "wlan0" "51" "100" ucidef_set_led_rssi "rssihigh" "RSSIHIGH" "$boardname:green:rssihigh" "wlan0" "76" "100" ;; +comfast,cf-e130n-v2) + ucidef_set_led_netdev "lan" "LAN" "$boardname:green:lan" "eth0" + ucidef_set_led_wlan "wlan" "WLAN" "$boardname:green:wlan" + ucidef_set_rssimon "wlan0" "200000" "1" + ucidef_set_led_rssi "rssilow" "RSSILOW" "$boardname:red:rssilow" "wlan0" "1" "100" + ucidef_set_led_rssi "rssimediumlow" "RSSIMEDIUMLOW" "$boardname:red:rssimediumlow" "wlan0" "26" "100" + ucidef_set_led_rssi "rssimediumhigh" "RSSIMEDIUMHIGH" "$boardname:green:rssimediumhigh" "wlan0" "51" "100" + ucidef_set_led_rssi "rssihigh" "RSSIHIGH" "$boardname:green:rssihigh" "wlan0" "76" "100" + ;; comfast,cf-e313ac) ucidef_set_led_switch "lan" "LAN" "$boardname:green:lan" "switch0" "0x02" ucidef_set_led_netdev "wan" "WAN" "$boardname:green:wan" "eth1" diff --git a/target/linux/ath79/generic/base-files/etc/board.d/02_network b/target/linux/ath79/generic/base-files/etc/board.d/02_network index 10ca213e70..5840b90bf6 100755 --- a/target/linux/ath79/generic/base-files/etc/board.d/02_network +++ b/target/linux/ath79/generic/base-files/etc/board.d/02_network @@ -86,6 +86,8 @@ ath79_setup_interfaces() ;; comfast,cf-e110n-v2|\ comfast,cf-e120a-v3|\ + comfast,cf-e130n-v2|\ + ucidef_set_interface_lan "eth1" comfast,cf-e314n-v2|\ tplink,cpe210-v1|\ tplink,cpe220-v2|\ diff --git a/target/linux/ath79/image/generic.mk b/target/linux/ath79/image/generic.mk index 70631c20d0..256481ece3 100644 --- a/target/linux/ath79/image/generic.mk +++ b/target/linux/ath79/image/generic.mk @@ -258,6 +258,16 @@ define Device/comfast_cf-e120a-v3 endef TARGET_DEVICES += comfast_cf-e120a-v3 +define Device/comfast_cf-e130n-v2 + ATH_SOC := qca9531 + DEVICE_VENDOR := COMFAST + DEVICE_MODEL := CF-E130N + DEVICE_VARIANT := v2 + DEVICE_PACKAGES := rssileds kmod-leds-gpio -swconfig -uboot-envtools + IMAGE_SIZE := 8000k +endef +TARGET_DEVICES += comfast_cf-e130n-v2 + define Device/comfast_cf-e313ac ATH_SOC := qca9531 DEVICE_VENDOR := COMFAST -- 2.17.1 _______________________________________________ openwrt-devel mailing list openwrt-devel@lists.openwrt.org https://lists.openwrt.org/mailman/listinfo/openwrt-devel