Sorry, I forgot to add the the target. I'll send again the patch
Thanks very much.
El dom., 27 oct. 2019 a las 14:05, John Crispin (<j...@phrozen.org>)
escribió:
> On 22/09/2019 22:05, Daniel Gonzalez Cabanelas wrote:
> > Add support for the Inventel DV4210 router.
> >
> > This is an Inventel Livebox 1 board. The patch supports the board with a
> CFE bootloader, and
> > a RAM mod (64 MB, tested). The board originally comes with 8 MB flash.
> Under this conditions
> > this old BCM6348 based board still runs quite fine with current
> snapshots.
> >
>
> Hi,
> thanks for the patch, the subject line needs to start with "brcm63xx:"
> John
>
> > Signed-off-by: Daniel Gonzalez Cabanelas <dgcb...@gmail.com>
> > ---
> > .../brcm63xx/base-files/etc/board.d/01_leds | 1 +
> > .../base-files/etc/board.d/02_network | 2 +-
> > target/linux/brcm63xx/base-files/etc/diag.sh | 1 +
> > .../linux/brcm63xx/base-files/lib/brcm63xx.sh | 3 +
> > target/linux/brcm63xx/dts/dv4210.dts | 102 ++++++++++++++++++
> > target/linux/brcm63xx/image/bcm63xx.mk | 13 +++
> > .../patches-4.14/599-board_DV4210.patch | 50 +++++++++
> > 7 files changed, 171 insertions(+), 1 deletion(-)
> > create mode 100644 target/linux/brcm63xx/dts/dv4210.dts
> > create mode 100644
> target/linux/brcm63xx/patches-4.14/599-board_DV4210.patch
> >
> > diff --git a/target/linux/brcm63xx/base-files/etc/board.d/01_leds
> b/target/linux/brcm63xx/base-files/etc/board.d/01_leds
> > index d25d37e847..00109ba112 100755
> > --- a/target/linux/brcm63xx/base-files/etc/board.d/01_leds
> > +++ b/target/linux/brcm63xx/base-files/etc/board.d/01_leds
> > @@ -69,6 +69,7 @@ homehub2a)
> > ucidef_set_led_usbdev "usb1" "USB1" "HOMEHUB2A:blue:phone" "1-1"
> > ucidef_set_led_usbdev "usb2" "USB2" "HOMEHUB2A:green:phone" "2-1"
> > ;;
> > +dv4210|\
> > livebox1)
> > ucidef_set_led_netdev "lan" "LAN" "Livebox1:red:traffic" "eth0"
> > ucidef_set_led_netdev "wan" "WAN" "Livebox1:red:adsl" "eth1"
> > diff --git a/target/linux/brcm63xx/base-files/etc/board.d/02_network
> b/target/linux/brcm63xx/base-files/etc/board.d/02_network
> > index a2ca5a37b3..0e384f82f6 100755
> > --- a/target/linux/brcm63xx/base-files/etc/board.d/02_network
> > +++ b/target/linux/brcm63xx/base-files/etc/board.d/02_network
> > @@ -145,8 +145,8 @@ bcm963268bu_p300)
> > ucidef_add_switch "switch0" \
> > "0:lan" "3:lan" "4:lan" "5:lan" "6:lan" "7:lan" "8t@eth0"
> > ;;
> > -
> > cpva502p |\
> > +dv4210 |\
> > livebox1)
> > ucidef_set_interfaces_lan_wan "eth0" "eth1"
> > ;;
> > diff --git a/target/linux/brcm63xx/base-files/etc/diag.sh
> b/target/linux/brcm63xx/base-files/etc/diag.sh
> > index 34464ec44a..c673a75e40 100644
> > --- a/target/linux/brcm63xx/base-files/etc/diag.sh
> > +++ b/target/linux/brcm63xx/base-files/etc/diag.sh
> > @@ -114,6 +114,7 @@ set_state() {
> > hg655b)
> > status_led="HW65x:green:power"
> > ;;
> > + dv4210|\
> > livebox1)
> > status_led="Livebox1:red:adsl-fail-power"
> > ;;
> > diff --git a/target/linux/brcm63xx/base-files/lib/brcm63xx.sh
> b/target/linux/brcm63xx/base-files/lib/brcm63xx.sh
> > index 1676ae0abb..9c0c33cc31 100755
> > --- a/target/linux/brcm63xx/base-files/lib/brcm63xx.sh
> > +++ b/target/linux/brcm63xx/base-files/lib/brcm63xx.sh
> > @@ -177,6 +177,9 @@ brcm63xx_dt_detect() {
> > "Inteno VG50")
> > board_name="vg50"
> > ;;
> > + "Inventel DV4210")
> > + board_name="dv4210"
> > + ;;
> > "Inventel Livebox 1")
> > board_name="livebox1"
> > ;;
> > diff --git a/target/linux/brcm63xx/dts/dv4210.dts
> b/target/linux/brcm63xx/dts/dv4210.dts
> > new file mode 100644
> > index 0000000000..02975fe3b6
> > --- /dev/null
> > +++ b/target/linux/brcm63xx/dts/dv4210.dts
> > @@ -0,0 +1,102 @@
> > +/dts-v1/;
> > +
> > +#include "bcm6348.dtsi"
> > +
> > +#include <dt-bindings/input/input.h>
> > +
> > +/ {
> > + model = "Inventel DV4210";
> > + compatible = "inventel,dv4210", "brcm,bcm6348";
> > +
> > + chosen {
> > + bootargs = "rootfstype=squashfs,jffs2 noinitrd
> console=ttyS0,115200";
> > + stdout-path = "serial0:115200n8";
> > + };
> > +
> > + keys {
> > + compatible = "gpio-keys-polled";
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + poll-interval = <20>;
> > +
> > + button1 {
> > + label = "1";
> > + gpios = <&pinctrl 36 1>;
> > + linux,code = <KEY_RESTART>;
> > + debounce-interval = <60>;
> > + };
> > +
> > + button2 {
> > + label = "2";
> > + gpios = <&pinctrl 7 1>;
> > + linux,code = <BTN_2>;
> > + debounce-interval = <60>;
> > + };
> > + };
> > +
> > + leds {
> > + compatible = "gpio-leds";
> > +
> > + red_adsl_fail {
> > + label = "Livebox1:red:adsl-fail-power";
> > + gpios = <&pinctrl 0 0>;
> > + default-state = "on";
> > + };
> > +
> > + red_adsl {
> > + label = "Livebox1:red:adsl";
> > + gpios = <&pinctrl 1 0>;
> > + };
> > +
> > + red_traffic {
> > + label = "Livebox1:red:traffic";
> > + gpios = <&pinctrl 2 0>;
> > + };
> > +
> > + red_phone {
> > + label = "Livebox1:red:phone";
> > + gpios = <&pinctrl 3 0>;
> > + };
> > +
> > + red_wifi {
> > + label = "Livebox1:red:wifi";
> > + gpios = <&pinctrl 4 0>;
> > + };
> > + };
> > +};
> > +
> > +&pflash {
> > + reg = <0x1f400000 0x800000>;
> > + status = "ok";
> > +
> > + partitions {
> > + compatible = "fixed-partitions";
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > +
> > + cfe@0 {
> > + reg = <0x000000 0x010000>;
> > + label = "cfe";
> > + };
> > +
> > + linux@10000 {
> > + reg = <0x010000 0x7e0000>;
> > + label = "linux";
> > + compatible = "brcm,bcm963xx-imagetag";
> > + };
> > +
> > + nvram@7f0000 {
> > + reg = <0x7f0000 0x010000>;
> > + label = "nvram";
> > + };
> > + };
> > +};
> > +
> > +&pinctrl {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_pci &pinctrl_ext_mii &pinctrl_mii_pccard>;
> > +};
> > +
> > +&uart0 {
> > + status = "ok";
> > +};
> > diff --git a/target/linux/brcm63xx/image/bcm63xx.mk
> b/target/linux/brcm63xx/image/bcm63xx.mk
> > index 212960e972..690ffb49fa 100644
> > --- a/target/linux/brcm63xx/image/bcm63xx.mk
> > +++ b/target/linux/brcm63xx/image/bcm63xx.mk
> > @@ -769,6 +769,19 @@ define Device/livebox
> > endef
> > TARGET_DEVICES += livebox
> >
> > +define Device/DV4210
> > + $(Device/bcm63xx)
> > + DEVICE_TITLE := Inventel DV4210
> > + DEVICE_DESCRIPTION = Build firmware images for the Inventel DV4210.
> Board with CFE bootloader and >32MB RAM
> > + DEVICE_DTS := dv4210
> > + CFE_BOARD_ID := DV4210
> > + CFE_CHIP_ID := 6348
> > + DEVICE_PACKAGES := \
> > + $(B43_PACKAGES) $(USB1_PACKAGES)
> > + DEFAULT := y
> > +endef
> > +TARGET_DEVICES += DV4210
> > +
> > ### Netgear ###
> > define Device/CVG834G
> > $(Device/bcm33xx)
> > diff --git a/target/linux/brcm63xx/patches-4.14/599-board_DV4210.patch
> b/target/linux/brcm63xx/patches-4.14/599-board_DV4210.patch
> > new file mode 100644
> > index 0000000000..618a214d63
> > --- /dev/null
> > +++ b/target/linux/brcm63xx/patches-4.14/599-board_DV4210.patch
> > @@ -0,0 +1,50 @@
> > +--- a/arch/mips/bcm63xx/boards/board_bcm963xx.c
> > ++++ b/arch/mips/bcm63xx/boards/board_bcm963xx.c
> > +@@ -1058,6 +1058,31 @@
> > + },
> > + };
> > +
> > ++static struct board_info __initdata board_DV4210 = {
> > ++ .name = "DV4210",
> > ++ .expected_cpu_id = 0x6348,
> > ++
> > ++ .has_enet0 = 1,
> > ++ .has_enet1 = 1,
> > ++ .has_pci = 1,
> > ++
> > ++ .enet0 = {
> > ++ .has_phy = 1,
> > ++ .use_internal_phy = 1,
> > ++ },
> > ++
> > ++ .enet1 = {
> > ++ .has_phy = 1,
> > ++ .phy_id = 31,
> > ++ },
> > ++
> > ++ .ephy_reset_gpio = 6,
> > ++ .ephy_reset_gpio_flags = GPIO_ACTIVE_LOW,
> > ++
> > ++ .has_ohci0 = 1,
> > ++ .has_pccard = 0,
> > ++};
> > ++
> > + static struct board_info __initdata board_96348A_122 = {
> > + .name = "96348A-122",
> > + .expected_cpu_id = 0x6348,
> > +@@ -2746,6 +2771,7 @@
> > + &board_FAST2404,
> > + &board_FAST2604,
> > + &board_DV201AMR,
> > ++ &board_DV4210,
> > + &board_96348gw_a,
> > + &board_rta1025w_16,
> > + &board_96348_D4PW,
> > +@@ -2859,6 +2885,7 @@
> > + { .compatible = "d-link,dsl-2640b-b", .data = &board_96348_D4PW, },
> > + { .compatible = "davolink,dv-201amr", .data = &board_DV201AMR, },
> > + { .compatible = "dynalink,rta1025w", .data = &board_rta1025w_16, },
> > ++ { .compatible = "inventel,dv4210", .data = &board_DV4210, },
> > + { .compatible = "netgear,dg834gtpn", .data = &board_96348gw_10, },
> > + { .compatible = "netgear,dg834g-v4", .data = &board_96348W3, },
> > + { .compatible = "sagem,f@st2404", .data = &board_FAST2404, },
> >
>
>
_______________________________________________
openwrt-devel mailing list
openwrt-devel@lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel
