From: Markus Scheck <mar...@mscheck.de>
- SoC: MediaTek MT7628AN
- Flash: 16MB (Winbond W25Q128JV)
- RAM: 64MB
- Serial: As marked on PCB, 3V3 logic, baudrate is 115200
- Ethernet: 3x 10/100 Mbps (switched, 2x LAN + WAN)
- WIFI0: MT7628AN 2.4GHz 802.11b/g/n
- WIFI1: MT7612EN 5GHz 802.11ac
- Antennas: 4x external (2 per radio), non-detachable
- LEDs: Programmable power-LED (two-colored, yellow/blue)
Non-programmable internet-LED (shows WAN-activity)
- Buttons: Reset
INSTALLATION:
1. Connect to the serial port of the router and power it up.
If you get a prompt asking for boot-mode, go to step 3.
2. Unplug the router after
> Erasing SPI Flash...
> raspi_erase: offs:20000 len:10000
occurs on the serial port. Plug the router back in.
3. At the prompt select option 2 (Load system code then
write to Flash via TFTP.)
4. Enter 192.168.1.1 as the device IP and 192.168.1.2 as the
Server-IP.
5. Connect your computer to LAN1 and assign it as 192.168.1.2/24.
6. Rename the sysupgrade image to test.bin and serve it via TFTP.
7. Enter test.bin on the serial console and press enter.
Signed-off-by: Markus Scheck <mar...@mscheck.de>
---
.../ramips/base-files/etc/board.d/02_network | 4 +
target/linux/ramips/base-files/lib/ramips.sh | 3 +
target/linux/ramips/dts/XIAOMI-MIR4A-100M.dts | 146 ++++++++++++++++++
target/linux/ramips/image/mt76x8.mk | 8 +
4 files changed, 161 insertions(+)
create mode 100644 target/linux/ramips/dts/XIAOMI-MIR4A-100M.dts
diff --git a/target/linux/ramips/base-files/etc/board.d/02_network
b/target/linux/ramips/base-files/etc/board.d/02_network
index c2646876a2..29a1e7b54c 100755
--- a/target/linux/ramips/base-files/etc/board.d/02_network
+++ b/target/linux/ramips/base-files/etc/board.d/02_network
@@ -450,6 +450,10 @@ ramips_setup_interfaces()
ucidef_add_switch "switch0" \
"1:lan:3" "2:lan:2" "3:lan:1" "4:wan" "6@eth0"
;;
+ xiaomi,mir4a-100m)
+ ucidef_add_switch "switch0" \
+ "4:lan:1" "2:lan:2" "0:wan" "6t@eth0"
+ ;;
zbtlink,zbt-we1226|\
y1)
ucidef_add_switch "switch0" \
diff --git a/target/linux/ramips/base-files/lib/ramips.sh
b/target/linux/ramips/base-files/lib/ramips.sh
index 093303892c..a9e7e746cd 100755
--- a/target/linux/ramips/base-files/lib/ramips.sh
+++ b/target/linux/ramips/base-files/lib/ramips.sh
@@ -649,6 +649,9 @@ ramips_board_detect() {
*"X8")
name="x8"
;;
+ *"Xiaomi Mi Router 4A (100M Edition)")
+ name="xiaomi,mir4a-100m"
+ ;;
*"Y1")
name="y1"
;;
diff --git a/target/linux/ramips/dts/XIAOMI-MIR4A-100M.dts
b/target/linux/ramips/dts/XIAOMI-MIR4A-100M.dts
new file mode 100644
index 0000000000..716b66ac44
--- /dev/null
+++ b/target/linux/ramips/dts/XIAOMI-MIR4A-100M.dts
@@ -0,0 +1,146 @@
+/dts-v1/;
+
+#include "mt7628an.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+/ {
+ compatible = "xiaomi,mir4a-100m", "mediatek,mt7628an-soc";
+ model = "Xiaomi Mi Router 4A (100M Edition)";
+
+ chosen {
+ bootargs = "console=ttyS0,115200";
+ };
+
+ memory@0 {
+ device_type = "memory";
+ reg = <0x0 0x4000000>;
+ };
+
+ aliases {
+ led-boot = &power_yellow;
+ led-failsafe = &power_yellow;
+ led-running = &power_blue;
+ led-upgrade = &power_yellow;
+ };
+
+ gpio-leds {
+ compatible = "gpio-leds";
+
+ power_blue: power_blue {
+ label = "mir4a-100m:blue:power";
+ gpios = <&gpio0 11 GPIO_ACTIVE_LOW>;
+ };
+
+ power_yellow: power_yellow {
+ label = "mir4a-100m:yellow:power";
+ gpios = <&gpio1 12 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ gpio-keys {
+ compatible = "gpio-keys-polled";
+ poll-interval = <20>;
+
+ reset {
+ label = "reset";
+ gpios = <&gpio1 6 GPIO_ACTIVE_LOW>;
+ linux,code = <KEY_RESTART>;
+ };
+ };
+};
+
+&spi0 {
+ status = "okay";
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <10000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "bootloader";
+ reg = <0x0 0x20000>;
+ read-only;
+ };
+
+ partition@20000 {
+ label = "config";
+ reg = <0x20000 0x10000>;
+ read-only;
+ };
+
+ factory: partition@30000 {
+ label = "factory";
+ reg = <0x30000 0x10000>;
+ read-only;
+ };
+
+ partition@40000 {
+ label = "crash";
+ reg = <0x40000 0x10000>;
+ read-only;
+ };
+
+ partition@50000 {
+ label = "cfg_bak";
+ reg = <0x50000 0x10000>;
+ read-only;
+ };
+
+ partition@60000 {
+ label = "overlay";
+ reg = <0x60000 0x100000>;
+ read-only;
+ };
+
+ partition@160000 {
+ compatible = "denx,uimage";
+ label = "firmware";
+ reg = <0x160000 0xea0000>;
+ };
+ };
+ };
+};
+
+&pcie {
+ status = "okay";
+
+ pcie-bridge {
+ mt76@0,0 {
+ reg = <0x0000 0 0 0 0>;
+ device_type = "pci";
+ mediatek,mtd-eeprom = <&factory 0x8000>;
+ mediatek,2ghz = <0>;
+ };
+ };
+};
+
+&pinctrl {
+ state_default: pinctrl0 {
+ gpio {
+ ralink,group = "gpio";
+ ralink,function = "gpio";
+ };
+ };
+};
+
+ðernet {
+ pinctrl-names = "default";
+ mtd-mac-address = <&factory 0x28>;
+};
+
+&esw {
+ mediatek,portmap = <0x2f>;
+ mediatek,portdisable = <0x2a>;
+};
+
+&wmac {
+ status = "okay";
+};
diff --git a/target/linux/ramips/image/mt76x8.mk
b/target/linux/ramips/image/mt76x8.mk
index 571ddf3d51..82659254cb 100644
--- a/target/linux/ramips/image/mt76x8.mk
+++ b/target/linux/ramips/image/mt76x8.mk
@@ -446,6 +446,14 @@ define Device/wrtnode2r
endef
TARGET_DEVICES += wrtnode2r
+define Device/xiaomi_mir4a-100m
+ DTS := XIAOMI-MIR4A-100M
+ IMAGE_SIZE := $(ralink_default_fw_size_16M)
+ DEVICE_TITLE := Xiaomi Mi Router 4A (100M Edition)
+ DEVICE_PACKAGES := kmod-mt76x2
+endef
+TARGET_DEVICES += xiaomi_mir4a-100m
+
define Device/zbtlink_zbt-we1226
DTS := ZBT-WE1226
IMAGE_SIZE := $(ralink_default_fw_size_8M)
--
2.21.0
_______________________________________________
openwrt-devel mailing list
openwrt-devel@lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel
