This patch adds supports for GL-X1200.
Specification:
- SOC: QCA9563 (775MHz)
- Flash: 16 MiB (W25Q128FVSG)
- RAM: 128 MiB DDR2
- Ethernet: 4x 1Gbps LAN + 1x 1Gbps WAN
- Wireless: QCA9563(2.4GHz) and QCA9886(5GHz)
- SIM: 2x SIM card slots
- MicroSD: 1x microSD slot
- Antenna: 2x external 5dBi antennas
- USB: 1x USB 2.0 port
- Button: 1x reset button
- LED: 16x LEDs (3x GPIO controllable)
- UART: 1x UART on PCB (JP1: 3.3V, RX, TX, GND)
Installation through Luci:
- The original firmware is openwrt, so both LuCI or sysupgrade can be
used.
- Do not keep settings, for sysupgrade please use the -n option.
Installation through bootloader webserver:
- Plug power and hold reset button until 2.4G LED light up.
- Install sysupgrade image using web interface on 192.168.1.1.
Signed-off-by: guilin wang <guilin.w...@gl-inet.com>
---
target/linux/ar71xx/base-files/etc/board.d/01_leds | 4 +
.../linux/ar71xx/base-files/etc/board.d/02_network | 4 +
.../etc/hotplug.d/firmware/11-ath10k-caldata | 5 +
target/linux/ar71xx/base-files/lib/ar71xx.sh | 3 +
.../ar71xx/base-files/lib/upgrade/platform.sh | 1 +
target/linux/ar71xx/config-4.14 | 1 +
.../ar71xx/files/arch/mips/ath79/Kconfig.openwrt | 11 ++
target/linux/ar71xx/files/arch/mips/ath79/Makefile | 1 +
.../ar71xx/files/arch/mips/ath79/mach-gl-x1200.c | 157 +++++++++++++++++++++
.../linux/ar71xx/files/arch/mips/ath79/machtypes.h | 1 +
target/linux/ar71xx/generic/config-default | 1 +
target/linux/ar71xx/image/generic.mk | 13 ++
12 files changed, 202 insertions(+)
create mode 100644 target/linux/ar71xx/files/arch/mips/ath79/mach-gl-x1200.c
diff --git a/target/linux/ar71xx/base-files/etc/board.d/01_leds
b/target/linux/ar71xx/base-files/etc/board.d/01_leds
index 41dd8c5..eb455ce 100755
--- a/target/linux/ar71xx/base-files/etc/board.d/01_leds
+++ b/target/linux/ar71xx/base-files/etc/board.d/01_leds
@@ -448,6 +448,10 @@ gl-inet)
ucidef_set_led_netdev "lan" "LAN" "$board:green:lan" "eth1"
ucidef_set_led_wlan "wlan" "WLAN" "$board:red:wlan" "phy0tpt"
;;
+gl-x1200)
+ ucidef_set_led_wlan "wlan2g" "WLAN2G" "$board:green:wlan2g" "phy1tpt"
+ ucidef_set_led_wlan "wlan5g" "WLAN5G" "$board:green:wlan5g" "phy0tpt"
+ ;;
hiwifi-hc6361)
ucidef_set_led_netdev "inet" "INET" "hiwifi:blue:internet" "eth1"
ucidef_set_led_wlan "wlan" "WLAN" "hiwifi:blue:wlan-2p4" "phy0tpt"
diff --git a/target/linux/ar71xx/base-files/etc/board.d/02_network
b/target/linux/ar71xx/base-files/etc/board.d/02_network
index 68874e0..6fd4c25 100755
--- a/target/linux/ar71xx/base-files/etc/board.d/02_network
+++ b/target/linux/ar71xx/base-files/etc/board.d/02_network
@@ -456,6 +456,10 @@ ar71xx_setup_interfaces()
ucidef_add_switch "switch0" \
"0@eth0" "2:lan:2" "3:lan:1" "1:wan"
;;
+ gl-x1200)
+ ucidef_add_switch "switch0" \
+ "0@eth0" "1:lan" "2:lan" "3:lan" "4:lan" "5:wan"
+ ;;
jwap230)
ucidef_set_interfaces_lan_wan "eth0.1" "eth1.2"
ucidef_add_switch "switch0" \
diff --git
a/target/linux/ar71xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
b/target/linux/ar71xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 2ded261..fd6f213 100644
--- a/target/linux/ar71xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ar71xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -187,6 +187,11 @@ case "$FIRMWARE" in
cf-e385ac)
ath10kcal_extract "art" 20480 12064
;;
+ gl-x1200)
+ ath10kcal_extract "art" 20480 12064
+ ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
+ /lib/firmware/ath10k/QCA9888/hw2.0/board.bin
+ ;;
esac
;;
*)
diff --git a/target/linux/ar71xx/base-files/lib/ar71xx.sh
b/target/linux/ar71xx/base-files/lib/ar71xx.sh
index 990683a..42902d0 100755
--- a/target/linux/ar71xx/base-files/lib/ar71xx.sh
+++ b/target/linux/ar71xx/base-files/lib/ar71xx.sh
@@ -794,6 +794,9 @@ ar71xx_board_detect() {
*"GL-USB150")
name="gl-usb150"
;;
+ *"GL-X1200")
+ name="gl-x1200"
+ ;;
*"HiveAP-121")
name="hiveap-121"
;;
diff --git a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
index 8173501..55be0a3 100755
--- a/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
+++ b/target/linux/ar71xx/base-files/lib/upgrade/platform.sh
@@ -273,6 +273,7 @@ platform_check_image() {
gl-domino|\
gl-mifi|\
gl-usb150|\
+ gl-x1200|\
hiwifi-hc6361|\
hornet-ub-x2|\
jwap230|\
diff --git a/target/linux/ar71xx/config-4.14 b/target/linux/ar71xx/config-4.14
index 9a524fa..8f8d8ce 100644
--- a/target/linux/ar71xx/config-4.14
+++ b/target/linux/ar71xx/config-4.14
@@ -130,6 +130,7 @@ CONFIG_ATH79=y
# CONFIG_ATH79_MACH_GL_INET is not set
# CONFIG_ATH79_MACH_GL_MIFI is not set
# CONFIG_ATH79_MACH_GL_USB150 is not set
+# CONFIG_ATH79_MACH_GL_X1200 is not set
# CONFIG_ATH79_MACH_GS_MINIBOX_V32 is not set
# CONFIG_ATH79_MACH_GS_OOLITE_V1 is not set
# CONFIG_ATH79_MACH_GS_OOLITE_V5_2 is not set
diff --git a/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt
b/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt
index 6fd78c4..c42fa16 100644
--- a/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt
+++ b/target/linux/ar71xx/files/arch/mips/ath79/Kconfig.openwrt
@@ -897,6 +897,17 @@ config ATH79_MACH_GL_USB150
select ATH79_DEV_M25P80
select ATH79_DEV_WMAC
+config ATH79_MACH_GL_X1200
+ bool "GL.iNet GL-X1200 support"
+ select SOC_QCA956X
+ select ATH79_DEV_AP9X_PCI if PCI
+ select ATH79_DEV_ETH
+ select ATH79_DEV_GPIO_BUTTONS
+ select ATH79_DEV_LEDS_GPIO
+ select ATH79_DEV_M25P80
+ select ATH79_DEV_USB
+ select ATH79_DEV_WMAC
+
config ATH79_MACH_EAP120
bool "TP-LINK EAP120 support"
select SOC_AR934X
diff --git a/target/linux/ar71xx/files/arch/mips/ath79/Makefile
b/target/linux/ar71xx/files/arch/mips/ath79/Makefile
index 0265b3d..9816175 100644
--- a/target/linux/ar71xx/files/arch/mips/ath79/Makefile
+++ b/target/linux/ar71xx/files/arch/mips/ath79/Makefile
@@ -140,6 +140,7 @@ obj-$(CONFIG_ATH79_MACH_GL_DOMINO) +=
mach-gl-domino.o
obj-$(CONFIG_ATH79_MACH_GL_INET) += mach-gl-inet.o
obj-$(CONFIG_ATH79_MACH_GL_MIFI) += mach-gl-mifi.o
obj-$(CONFIG_ATH79_MACH_GL_USB150) += mach-gl-usb150.o
+obj-$(CONFIG_ATH79_MACH_GL_X1200) += mach-gl-x1200.o
obj-$(CONFIG_ATH79_MACH_GS_MINIBOX_V32) += mach-gs-minibox-v32.o
obj-$(CONFIG_ATH79_MACH_GS_OOLITE_V1) += mach-gs-oolite-v1.o
obj-$(CONFIG_ATH79_MACH_GS_OOLITE_V5_2) += mach-gs-oolite-v5-2.o
diff --git a/target/linux/ar71xx/files/arch/mips/ath79/mach-gl-x1200.c
b/target/linux/ar71xx/files/arch/mips/ath79/mach-gl-x1200.c
new file mode 100644
index 0000000..873a608
--- /dev/null
+++ b/target/linux/ar71xx/files/arch/mips/ath79/mach-gl-x1200.c
@@ -0,0 +1,157 @@
+/*
+ * GL.iNet GL-X1200 board support
+ *
+ * Copyright (C) 2018 guilin wang <guilin.w...@gl-inet.com>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+#include <linux/init.h>
+#include <linux/gpio.h>
+#include <linux/platform_device.h>
+#include <linux/ath9k_platform.h>
+#include <linux/ar8216_platform.h>
+#include <linux/etherdevice.h>
+
+#include <asm/mach-ath79/ath79.h>
+#include <asm/mach-ath79/irq.h>
+#include <asm/mach-ath79/ar71xx_regs.h>
+
+#include <linux/platform_data/phy-at803x.h>
+
+#include "common.h"
+#include "dev-ap9x-pci.h"
+#include "dev-eth.h"
+#include "dev-gpio-buttons.h"
+#include "dev-leds-gpio.h"
+#include "dev-spi.h"
+#include "dev-m25p80.h"
+#include "dev-wmac.h"
+#include "dev-usb.h"
+#include "machtypes.h"
+#include "pci.h"
+
+#define GL_X1200_KEYS_POLL_INTERVAL 20
+#define GL_X1200_KEYS_DEBOUNCE_INTERVAL (3 *
GL_X1200_KEYS_POLL_INTERVAL)
+
+#define GL_X1200_GPIO_EXT_WDT 16
+#define GL_X1200_GPIO_LED_WLAN2G 19
+#define GL_X1200_GPIO_LED_WLAN5G 20
+#define GL_X1200_GPIO_LED_POWER 8
+#define GL_X1200_GPIO_USB_POWER 7
+
+#define GL_X1200_GPIO_BTN_RESET 2
+
+#define GL_X1200_MAC0_OFFSET 0x0000
+#define GL_X1200_WMAC_CALDATA_OFFSET 0x1000
+#define GL_X1200_PCI_CALDATA_OFFSET 0x5000
+
+static void __init gl_x1200_ext_watchdog_setup(int gpio_wdt)
+{
+ int state = 0;
+ int i = 0;
+ if (gpio_wdt) {
+ gpio_request_one(gpio_wdt, GPIOF_OUT_INIT_HIGH,
+ "gl-x1200:watchdog");
+ //disable watchdog
+ for(i = 0; i < 20; i++) {
+ state = !state;
+ gpio_set_value(gpio_wdt, state);
+ msleep(10);
+ }
+ }
+}
+
+static struct gpio_led gl_x1200_leds_gpio[] __initdata = {
+ {
+ .name = "gl-x1200:green:power",
+ .gpio = GL_X1200_GPIO_LED_POWER,
+ .default_state = LEDS_GPIO_DEFSTATE_KEEP,
+ .active_low = 1,
+ },{
+ .name = "gl-x1200:green:usbpower",
+ .gpio = GL_X1200_GPIO_USB_POWER,
+ .active_low = 1,
+ },{
+ .name = "gl-x1200:green:wlan2g",
+ .gpio = GL_X1200_GPIO_LED_WLAN2G,
+ .active_low = 1,
+ },{
+ .name = "gl-x1200:green:wlan5g",
+ .gpio = GL_X1200_GPIO_LED_WLAN5G,
+ .active_low = 0,
+ }
+};
+
+static struct gpio_keys_button gl_x1200_gpio_keys[] __initdata = {
+ {
+ .desc = "reset",
+ .type = EV_KEY,
+ .code = KEY_RESTART,
+ .debounce_interval = GL_X1200_KEYS_DEBOUNCE_INTERVAL,
+ .gpio = GL_X1200_GPIO_BTN_RESET,
+ .active_low = 1,
+ },
+};
+
+static struct ar8327_pad_cfg gl_x1200_ar8327_pad0_cfg = {
+ .mode = AR8327_PAD_MAC_SGMII,
+ .sgmii_delay_en = true,
+};
+
+static struct ar8327_platform_data gl_x1200_ar8327_data = {
+ .pad0_cfg = &gl_x1200_ar8327_pad0_cfg,
+ .port0_cfg = {
+ .force_link = 1,
+ .speed = AR8327_PORT_SPEED_1000,
+ .duplex = 1,
+ .txpause = 1,
+ .rxpause = 1,
+ },
+};
+
+
+static struct mdio_board_info gl_x1200_mdio0_info[] = {
+ {
+ .bus_id = "ag71xx-mdio.0",
+ .mdio_addr = 0,
+ .platform_data = &gl_x1200_ar8327_data,
+ },
+};
+
+static void __init gl_x1200_setup(void)
+{
+ u8 *eeprom = (u8 *) KSEG1ADDR(0x1f050000);
+
+ ath79_register_m25p80(NULL);
+
+ ath79_init_mac(ath79_eth0_data.mac_addr,
+ eeprom + GL_X1200_MAC0_OFFSET, 0);
+
+ ath79_eth0_data.phy_if_mode = PHY_INTERFACE_MODE_SGMII;
+ ath79_eth0_data.mii_bus_dev = &ath79_mdio0_device.dev;
+ ath79_eth0_data.phy_mask = BIT(0);
+
+ mdiobus_register_board_info(gl_x1200_mdio0_info,
+ ARRAY_SIZE(gl_x1200_mdio0_info));
+ ath79_register_mdio(0, 0x00);
+ ath79_register_eth(0);
+ ath79_register_usb();
+
+ ath79_gpio_function_enable(AR934X_GPIO_FUNC_JTAG_DISABLE);
+
+ ath79_register_wmac(eeprom + GL_X1200_WMAC_CALDATA_OFFSET, NULL);
+ ap91_pci_init(eeprom + GL_X1200_PCI_CALDATA_OFFSET, NULL);
+
+ ath79_register_leds_gpio(-1, ARRAY_SIZE(gl_x1200_leds_gpio),
+ gl_x1200_leds_gpio);
+
+ ath79_register_gpio_keys_polled(-1, GL_X1200_KEYS_POLL_INTERVAL,
+ ARRAY_SIZE(gl_x1200_gpio_keys),
+ gl_x1200_gpio_keys);
+ gl_x1200_ext_watchdog_setup(GL_X1200_GPIO_EXT_WDT);
+}
+
+MIPS_MACHINE(ATH79_MACH_GL_X1200, "GL-X1200", "GL-X1200",
+ gl_x1200_setup);
diff --git a/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h
b/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h
index 9722744..f5c3e3d 100644
--- a/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h
+++ b/target/linux/ar71xx/files/arch/mips/ath79/machtypes.h
@@ -138,6 +138,7 @@ enum ath79_mach_type {
ATH79_MACH_GL_INET, /* GL-CONNECT GL-INET */
ATH79_MACH_GL_MIFI, /* GL-MIFI support */
ATH79_MACH_GL_USB150, /* GL.iNet GL-USB150 */
+ ATH79_MACH_GL_X1200, /* GL.iNet GL-X1200 */
ATH79_MACH_GS_MINIBOX_V1, /* GainStrong MiniBox V1.0 */
ATH79_MACH_GS_MINIBOX_V32, /* Gainstrong MiniBox V3.2 */
ATH79_MACH_GS_OOLITE_V1, /* GainStrong Oolite V1.0 */
diff --git a/target/linux/ar71xx/generic/config-default
b/target/linux/ar71xx/generic/config-default
index 25b58ae..de7586f 100644
--- a/target/linux/ar71xx/generic/config-default
+++ b/target/linux/ar71xx/generic/config-default
@@ -99,6 +99,7 @@ CONFIG_ATH79_MACH_GL_DOMINO=y
CONFIG_ATH79_MACH_GL_INET=y
CONFIG_ATH79_MACH_GL_MIFI=y
CONFIG_ATH79_MACH_GL_USB150=y
+CONFIG_ATH79_MACH_GL_X1200=y
CONFIG_ATH79_MACH_GS_MINIBOX_V32=y
CONFIG_ATH79_MACH_GS_OOLITE_V1=y
CONFIG_ATH79_MACH_GS_OOLITE_V5_2=y
diff --git a/target/linux/ar71xx/image/generic.mk
b/target/linux/ar71xx/image/generic.mk
index 30a8b34..2018333 100644
--- a/target/linux/ar71xx/image/generic.mk
+++ b/target/linux/ar71xx/image/generic.mk
@@ -543,6 +543,19 @@ define Device/gl-usb150
endef
TARGET_DEVICES += gl-usb150
+define Device/gl-x1200
+ DEVICE_TITLE := GL.iNet GL-X1200
+ DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-usb-storage \
+ kmod-ath10k ath10k-firmware-qca9888
+ BOARDNAME := GL-X1200
+ SUPPORTED_DEVICES := gl-x1200
+ IMAGE_SIZE := 16000k
+ MTDPARTS := spi0.0:256k(u-boot)ro,64k(u-boot-env),64k(art)ro,-(firmware)
+ IMAGE/sysupgrade.bin := append-kernel | pad-to $$$$(BLOCKSIZE) | \
+ append-rootfs | pad-rootfs | append-metadata | check-size
$$$$(IMAGE_SIZE)
+endef
+TARGET_DEVICES += gl-x1200
+
define Device/lan-turtle
$(Device/tplink-16mlzma)
DEVICE_TITLE := Hak5 LAN Turtle
--
2.7.4
_______________________________________________
openwrt-devel mailing list
openwrt-devel@lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel
