Hi,
I've just added support for the COMFAST CF-E313AC, an outdoor wireless
CPE with two Ethernet ports and a 802.11ac radio (see patch below).
Everything is working fine but I've got two issues for which I'd like to
get some advise:
1) target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
I had to add "rm /lib/firmware/ath10k/QCA9888/hw2.0/board-2.bin", since
the driver tries to board-2.bin (the default calibration data from the
firmware package) first and, when that file is not found, falls back to
board.bin (the calibration data read from the flash).
I haven't seen this on any other device, so I guess there must be a more
elegant way to deal with it. Any idea?
2) target/linux/ath79/dts/qca9531_comfast_cf-e313ac.dts
The device is equipped with a "w25q128" flash chip (16384 Kbytes) but the
stock firmware image only used half of it (nvram partition finishes at
0x000000800000, i.e., 8192 Kbytes):
*** stock firmware bootlog ***
[...]
[ 0.730000] 0x000000000000-0x000000010000 : "u-boot"
[ 0.740000] 0x000000010000-0x000000020000 : "art"
[ 0.740000] 0x000000020000-0x0000001a0000 : "kernel"
[ 0.750000] 0x0000001a0000-0x0000007e0000 : "rootfs"
[ 0.760000] mtd: device 3 (rootfs) set to be root filesystem
[ 0.760000] 1 squashfs-split partitions found on MTD device rootfs
[ 0.770000] 0x0000006c0000-0x0000007e0000 : "rootfs_data"
[ 0.780000] 0x0000007e0000-0x0000007f0000 : "configs"
[ 0.780000] 0x0000007f0000-0x000000800000 : "nvram"
[ 0.790000] 0x000000020000-0x0000007e0000 : "firmware"
[...]
Is there a way to use the remaining half of the flash?
Any comments regarding these or other issues will be highly appreciated.
Thanks!
---
.../ath79/base-files/etc/board.d/01_leds | 9 ++
.../etc/hotplug.d/firmware/11-ath10k-caldata | 7 +
.../ath79/dts/qca9531_comfast_cf-e313ac.dts | 143 ++++++++++++++++++
target/linux/ath79/image/generic.mk | 8 +
4 files changed, 167 insertions(+)
create mode 100644 target/linux/ath79/dts/qca9531_comfast_cf-e313ac.dts
diff --git a/target/linux/ath79/base-files/etc/board.d/01_leds
b/target/linux/ath79/base-files/etc/board.d/01_leds
index db5a6a4578..50c9ca2a8d 100755
--- a/target/linux/ath79/base-files/etc/board.d/01_leds
+++ b/target/linux/ath79/base-files/etc/board.d/01_leds
@@ -47,6 +47,15 @@ comfast,cf-e120a-v3)
ucidef_set_led_rssi "rssimediumhigh" "RSSIMEDIUMHIGH"
"$boardname:green:rssimediumhigh" "wlan0" "51" "100"
ucidef_set_led_rssi "rssihigh" "RSSIHIGH" "$boardname:green:rssihigh"
"wlan0" "76" "100"
;;
+comfast,cf-e313ac)
+ ucidef_set_led_netdev "lan" "LAN" "$boardname:green:lan" "eth0"
+ ucidef_set_led_switch "wan" "WAN" "$boardname:green:wan" "switch0"
"0x02"
+ ucidef_set_rssimon "wlan0" "200000" "1"
+ ucidef_set_led_rssi "rssilow" "RSSILOW" "$boardname:red:rssilow"
"wlan0" "1" "100"
+ ucidef_set_led_rssi "rssimediumlow" "RSSIMEDIUMLOW"
"$boardname:red:rssimediumlow" "wlan0" "26" "100"
+ ucidef_set_led_rssi "rssimediumhigh" "RSSIMEDIUMHIGH"
"$boardname:green:rssimediumhigh" "wlan0" "51" "100"
+ ucidef_set_led_rssi "rssihigh" "RSSIHIGH" "$boardname:green:rssihigh"
"wlan0" "76" "100"
+ ;;
dlink,dir-859-a1)
ucidef_set_led_switch "internet" "WAN" "$boardname:green:internet"
"switch0" "0x20"
;;
diff --git
a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
index 8651c97099..3096c4e1e8 100644
--- a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
+++ b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata
@@ -162,6 +162,13 @@ case "$FIRMWARE" in
;;
"ath10k/pre-cal-pci-0000:00:00.0.bin")
case $board in
+ comfast,cf-e313ac)
+ ath10kcal_extract "art" 20480 12064
+ ath10kcal_patch_mac_crc $(mtd_get_mac_binary art 4098)
+ ln -sf /lib/firmware/ath10k/pre-cal-pci-0000\:00\:00.0.bin \
+ /lib/firmware/ath10k/QCA9888/hw2.0/board.bin
+ rm /lib/firmware/ath10k/QCA9888/hw2.0/board-2.bin
+ ;;
phicomm,k2t)
ath10kcal_extract "art" 20480 12064
ath10kcal_patch_mac_crc $(k2t_get_mac "5g_mac")
diff --git a/target/linux/ath79/dts/qca9531_comfast_cf-e313ac.dts
b/target/linux/ath79/dts/qca9531_comfast_cf-e313ac.dts
new file mode 100644
index 0000000000..cf6587b615
--- /dev/null
+++ b/target/linux/ath79/dts/qca9531_comfast_cf-e313ac.dts
@@ -0,0 +1,143 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+
+#include "qca953x.dtsi"
+
+/ {
+ compatible = "comfast,cf-e313ac", "qca,qca9531";
+ model = "COMFAST CF-E313AC";
+
+ aliases {
+ serial0 = &uart;
+ led-boot = &wan;
+ led-failsafe = &wan;
+ led-upgrade = &wan;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ pinctrl-names = "default";
+
+ wan: wan {
+ label = "cf-e313ac:green:wan";
+ gpios = <&gpio 0 GPIO_ACTIVE_LOW>;
+ };
+
+ lan: lan {
+ label = "cf-e313ac:green:lan";
+ gpios = <&gpio 2 GPIO_ACTIVE_LOW>;
+ };
+
+ wlan: wlan {
+ label = "cf-e313ac:green:wlan";
+ gpios = <&gpio 3 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "phy0tpt";
+ };
+
+ rssilow {
+ label = "cf-e313ac:red:rssilow";
+ gpios = <&gpio 11 GPIO_ACTIVE_LOW>;
+ };
+
+ rssimediumlow {
+ label = "cf-e313ac:red:rssimediumlow";
+ gpios = <&gpio 12 GPIO_ACTIVE_LOW>;
+ };
+
+ rssimediumhigh {
+ label = "cf-e313ac:green:rssimediumhigh";
+ gpios = <&gpio 14 GPIO_ACTIVE_LOW>;
+ };
+
+ rssihigh {
+ label = "cf-e313ac:green:rssihigh";
+ gpios = <&gpio 16 GPIO_ACTIVE_LOW>;
+ };
+ };
+
+ keys {
+ compatible = "gpio-keys-polled";
+ poll-interval = <20>;
+
+ reset {
+ label = "reset";
+ linux,code = <KEY_RESTART>;
+ gpios = <&gpio 17 GPIO_ACTIVE_LOW>;
+ debounce-interval = <60>;
+ };
+ };
+};
+
+&spi {
+ status = "okay";
+ num-cs = <1>;
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <25000000>;
+
+ partitions {
+ compatible = "fixed-partitions";
+ #address-cells = <1>;
+ #size-cells = <1>;
+
+ partition@0 {
+ label = "u-boot";
+ reg = <0x000000 0x010000>;
+ read-only;
+ };
+
+ art: partition@10000 {
+ label = "art";
+ reg = <0x010000 0x010000>;
+ read-only;
+ };
+
+ partition@20000 {
+ compatible = "denx,uimage";
+ label = "firmware";
+ reg = <0x020000 0x7c0000>;
+ };
+
+ partition@7e0000 {
+ label = "configs";
+ reg = <0x7e0000 0x010000>;
+ read-only;
+ };
+
+ partition@7f0000 {
+ label = "nvram";
+ reg = <0x7f0000 0x010000>;
+ read-only;
+ };
+ };
+ };
+};
+
+&uart {
+ status = "okay";
+};
+
+ð0 {
+ status = "okay";
+ mtd-mac-address = <&art 0x0>;
+ phy-handle = <&swphy4>;
+};
+
+ð1 {
+ status = "okay";
+ mtd-mac-address = <&art 0x6>;
+
+ gmac-config {
+ device = <&gmac>;
+ };
+};
+
+&pcie0 {
+ status = "okay";
+};
diff --git a/target/linux/ath79/image/generic.mk
b/target/linux/ath79/image/generic.mk
index ddf0e62898..69a29ab8fd 100644
--- a/target/linux/ath79/image/generic.mk
+++ b/target/linux/ath79/image/generic.mk
@@ -171,6 +171,14 @@ define Device/comfast_cf-e120a-v3
endef
TARGET_DEVICES += comfast_cf-e120a-v3
+define Device/comfast_cf-e313ac
+ ATH_SOC := qca9531
+ DEVICE_TITLE := COMFAST CF-E313AC
+ DEVICE_PACKAGES := rssileds kmod-leds-gpio kmod-ath10k-ct
ath10k-firmware-qca9888-ct
+ IMAGE_SIZE := 8000k
+endef
+TARGET_DEVICES += comfast_cf-e313ac
+
define Device/devolo_dvl1200e
ATH_SOC := qca9558
DEVICE_TITLE := devolo WiFi pro 1200e
--
2.20.1
_______________________________________________
openwrt-devel mailing list
openwrt-devel@lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel
