Hey, I stumbled of some more stuff. Comments inline.
Am So., 30. Dez. 2018 um 13:27 Uhr schrieb Christoph Krapp via openwrt-devel <openwrt-devel@lists.openwrt.org>: > > The sender domain has a DMARC Reject/Quarantine policy which disallows > sending mailing list messages using the original "From" header. > > To mitigate this problem, the original message has been wrapped > automatically by the mailing list software. > > > ---------- Forwarded message ---------- > From: Christoph Krapp <achte...@googlemail.com> > To: openwrt-devel@lists.openwrt.org > Cc: > Bcc: > Date: Sun, 30 Dec 2018 13:26:31 +0100 > Subject: [PATCH] ath79: add support for GL.iNet GL-AR750S > This patch adds supports for GL-AR750S. > Right now this patch only adds nor image generation. > NAND image generation is not supportet at the moment. > > Specification: > - SOC: QCA9563 (775MHz) > - Flash: 16 MiB (W25Q128FVSG) > - RAM: 128 MiB DDR2 > - Ethernet: 2x 1Gbps LAN + 1x 1Gbps WAN > - Wireless: 2.4GHz (bgn) and 5GHz (ac) > - USB: 1x USB 2.0 port > - Button: 1x switch button, 1x reset button > - LED: 3x LEDS (green) The gl.Inet webpage mentions a " TF Card Slot (128GB Max.) " as well. Any idea if it works and how it might be connected? > > Flash instruction: > - Set static ip to 192.168.1.2 > - Unplug the power cord > - Hold reset button > - Plug power back in > - Right led will flash 5 times > - Release reset button > - Browse to 192.168.1.1 > - Choose sysupgrade image in NOR-flash section > - Press "update nor firmware" > - After successful transfer unplug network cable before device restarts > > Signed-off-by: Christoph Krapp <achte...@googlemail.com> > --- > .../ath79/base-files/etc/board.d/02_network | 4 + > .../etc/hotplug.d/firmware/11-ath10k-caldata | 9 +- > .../linux/ath79/dts/qca9563_glinet_ar750s.dts | 160 ++++++++++++++++++ > target/linux/ath79/image/generic.mk | 9 + > 4 files changed, 178 insertions(+), 4 deletions(-) > create mode 100644 target/linux/ath79/dts/qca9563_glinet_ar750s.dts > > diff --git a/target/linux/ath79/base-files/etc/board.d/02_network > b/target/linux/ath79/base-files/etc/board.d/02_network > index 004ab59573..b9a0f356bf 100755 > --- a/target/linux/ath79/base-files/etc/board.d/02_network > +++ b/target/linux/ath79/base-files/etc/board.d/02_network > @@ -93,6 +93,10 @@ ath79_setup_interfaces() > glinet,gl-x750) > ucidef_set_interfaces_lan_wan "eth1" "eth0" > ;; > + glinet,ar750s) > + ucidef_add_switch "switch0" \ > + "0@eth0" "2:lan:2" "3:lan:1" "1:wan" > + ;; > nec,wg800hp) > ucidef_add_switch "switch0" \ > "0@eth0" "2:lan" "3:lan" "4:lan" "1:wan" > diff --git > a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata > b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata > index 53f57be824..2118d2b06b 100644 > --- a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata > +++ b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata > @@ -92,6 +92,11 @@ case "$FIRMWARE" in > ath10kcal_extract "art" 20480 2116 > ath10kcal_patch_mac_crc $(macaddr_add $(mtd_get_mac_binary > art 0) -1) > ;; > + glinet,ar750s|\ > + tplink,re450-v2) > + ath10kcal_extract "art" 20480 2116 > + ath10kcal_patch_mac $(macaddr_add $(cat > /sys/class/net/eth0/address) +1) > + ;; > glinet,gl-x750) > ath10kcal_extract "art" 20480 2116 > ath10kcal_patch_mac $(macaddr_add $(cat > /sys/class/net/eth0/address) +1) > @@ -122,10 +127,6 @@ case "$FIRMWARE" in > ath10kcal_extract "art" 20480 2116 > ath10kcal_patch_mac $(macaddr_add $(cat > /sys/class/net/eth0/address) -1) > ;; > - tplink,re450-v2) > - ath10kcal_extract "art" 20480 2116 > - ath10kcal_patch_mac $(macaddr_add $(cat > /sys/class/net/eth0/address) +1) > - ;; > ubnt,unifiac-lite|\ > ubnt,unifiac-mesh|\ > ubnt,unifiac-mesh-pro|\ > diff --git a/target/linux/ath79/dts/qca9563_glinet_ar750s.dts > b/target/linux/ath79/dts/qca9563_glinet_ar750s.dts > new file mode 100644 > index 0000000000..eff7aafaf6 > --- /dev/null > +++ b/target/linux/ath79/dts/qca9563_glinet_ar750s.dts > @@ -0,0 +1,160 @@ > +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT > +/dts-v1/; > + > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/input/input.h> > + > +#include "qca956x.dtsi" > + > +/ { > + compatible = "glinet,ar750s", "qca,qca9563"; > + model = "GL.iNet GL-AR750S"; > + > + chosen { > + bootargs = "console=ttyS0,115200n8"; > + }; > + > + aliases { > + led-boot = &power; > + led-failsafe = &power; > + led-running = &power; > + led-upgrade = &power; > + }; > + > + keys { > + compatible = "gpio-keys-polled"; > + poll-interval = <20>; > + pinctrl-names = "default"; > + pinctrl-0 = <&jtag_disable_pins>; > + > + button0 { > + label = "reset"; > + linux,code = <KEY_RESTART>; > + gpios = <&gpio 2 GPIO_ACTIVE_LOW>; > + }; > + > + button1 { > + label = "button right"; > + linux,code = <BTN_0>; > + gpios = <&gpio 8 GPIO_ACTIVE_LOW>; > + }; > + If you have to send a third version of this patch, please drop this blank line. > + }; > + > + leds { > + compatible = "gpio-leds"; > + > + power: power { > + label = "gl-ar750s:green:power"; > + gpios = <&gpio 1 GPIO_ACTIVE_LOW>; > + default-state = "keep"; > + }; > + > + usbpower { > + label = "gl-ar750s:green:usbpower"; > + gpios = <&gpio 7 GPIO_ACTIVE_LOW>; > + }; This still looks wrong to me. Since you mentioned only three leds in the commit message, I assume it is a GPIO which need to be pulled to enable or disable USB power. Please grep for gpio-export to see how it is done right. > + > + wlan2g { > + label = "gl-ar750s:green:wlan2g"; > + gpios = <&gpio 19 GPIO_ACTIVE_LOW>; > + linux,default-trigger = "phy1tpt"; > + }; > + > + wlan5g { > + label = "gl-ar750s:green:wlan5g"; > + gpios = <&gpio 20 GPIO_ACTIVE_HIGH>; > + linux,default-trigger = "phy0tpt"; > + }; > + }; > +}; > + > +&spi { > + status = "okay"; > + num-cs = <0>; > + > + flash@0 { > + compatible = "jedec,spi-nor"; > + reg = <0>; > + spi-max-frequency = <25000000>; > + > + partitions { > + compatible = "fixed-partitions"; > + #address-cells = <1>; > + #size-cells = <1>; > + > + partition@0 { > + label = "u-boot"; > + reg = <0x000000 0x040000>; > + read-only; > + }; > + > + partition@40000 { > + label = "u-boot-env"; > + reg = <0x040000 0x010000>; > + }; > + > + art: partition@50000 { > + label = "art"; > + reg = <0x050000 0x010000>; > + }; > + > + partition@60000 { > + compatible = "denx,uimage"; > + label = "firmware"; > + reg = <0x060000 0xfa0000>; > + }; > + If you have to send a third version of this patch, please drop this blank line. > + }; > + }; > +}; > + > +&pcie { > + status = "okay"; > +}; > + > +&uart { > + status = "okay"; > +}; > + > +&usb0 { > + #address-cells = <1>; > + #size-cells = <0>; > + status = "okay"; > + > + hub_port: port@1 { > + reg = <1>; > + #trigger-source-cells = <0>; > + }; > +}; > + > +&usb_phy0 { > + status = "okay"; > +}; > + > +&mdio0 { > + status = "okay"; > + phy-mask = <0>; > + > + phy0: ethernet-phy@0 { > + reg = <0>; > + phy-mode = "sgmii"; > + qca,ar8327-initvals = < > + 0x04 0x00080080 /* PORT0 PAD MODE CTRL */ > + 0x7c 0x0000007e /* PORT0_STATUS */ > + >; > + }; > +}; > + > +ð0 { > + status = "okay"; > + > + mtd-mac-address = <&art 0x0>; > + phy-handle = <&phy0>; > +}; > + > +&wmac { > + status = "okay"; > + mtd-cal-data = <&art 0x1000>; > + mtd-mac-address = <&art 0x1002>; > +}; > diff --git a/target/linux/ath79/image/generic.mk > b/target/linux/ath79/image/generic.mk > index b2f83ba58c..c61148d50e 100644 > --- a/target/linux/ath79/image/generic.mk > +++ b/target/linux/ath79/image/generic.mk > @@ -237,6 +237,15 @@ define Device/glinet_ar300m-nor > endef > TARGET_DEVICES += glinet_ar300m-nor > > +define Device/glinet_ar750s > + ATH_SOC := qca9563 > + DEVICE_TITLE := GL.iNet GL-AR750S > + DEVICE_PACKAGES := kmod-usb2 kmod-ath10k-ct ath10k-firmware-qca988x-ct > + IMAGE_SIZE := 16000k > + SUPPORTED_DEVICES += gl-ar750s > +endef > +TARGET_DEVICES += glinet_ar750s > + > define Device/glinet_gl-x750 > ATH_SOC := qca9531 > DEVICE_TITLE := GL.iNet GL-X750 > -- > 2.19.2 > > > _______________________________________________ > openwrt-devel mailing list > openwrt-devel@lists.openwrt.org > https://lists.openwrt.org/mailman/listinfo/openwrt-devel _______________________________________________ openwrt-devel mailing list openwrt-devel@lists.openwrt.org https://lists.openwrt.org/mailman/listinfo/openwrt-devel