W dniu 28.11.2018 o 20:34, Lucian Cristian pisze: > On 27.11.2018 19:59, John Crispin wrote: >> >> On 27/11/2018 18:15, Tomasz Maciej Nowak wrote: >>> W dniu 27.11.2018 o 18:04, John Crispin pisze: >>>> On 27/11/2018 16:11, Tomasz Maciej Nowak wrote: >>>>> W dniu 27.11.2018 o 14:47, Lucian Cristian pisze: >>>>>> On 26.11.2018 23:58, Tomasz Maciej Nowak wrote: >>>>>>> W dniu 26.11.2018 o 22:47, Lucian Cristian pisze: >>>>>>>> On 26.11.2018 23:11, Tomasz Maciej Nowak wrote: >>>>>>>>> W dniu 26.11.2018 o 21:44, Lucian Cristian pisze: >>>>>>>>>> On 20.11.2018 18:20, Tomasz Maciej Nowak wrote: >>>>>>>>>>> This small series addresses current problem with late loading of >>>>>>>>>>> Intel >>>>>>>>>>> microcode in OpenWrt. Following the commit messages [1] and later >>>>>>>>>>> discussion, late loading off the microcode can be ineffective for >>>>>>>>>>> some >>>>>>>>>>> processors [2] and for others disabled [3]. Also it is discouraged >>>>>>>>>>> for >>>>>>>>>>> any processor starting from Haswell and Silvermont. >>>>>>>>>>> Therefore this series converts the Intel microcode bundle to an >>>>>>>>>>> initial >>>>>>>>>>> ram disk which is loaded with grub, so kernel has access to it as >>>>>>>>>>> early >>>>>>>>>>> as possible. >>>>>>>>>>> Previous patch series: >>>>>>>>>>> https://patchwork.ozlabs.org/project/lede/list/?series=39372 >>>>>>>>>>> >>>>>>>>>>> 1. https://lore.kernel.org/patchwork/cover/348236 >>>>>>>>>>> 2. https://lore.kernel.org/patchwork/cover/348236/#508603 >>>>>>>>>>> 3. >>>>>>>>>>> https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/?id=723f2828a98c8ca19842042f418fb30dd8cfc0f7 >>>>>> [...] >>>>>>>>>>> No, Your grub doesn't understand *if* command because it's old an >>>>>>>>>>> doesn't have "test" module enabled. It's left there because >>>>>>>>>>> sysupgrade doesn't upgrade grub, it updates only boot and root >>>>>>>>>>> partitions. If You'll write the created image not by sysupgrade but >>>>>>>>>>> by dd'ing to boot medium, It'll start properly without >>>>>>>>>>> interruptions. >>>>>>>>>>> BTW thank You for the report. >>>>>>>>>>> >>>>>>>> error: can't find command '['. >>>>>>>> error: can't find command '['. >>>>>>>> >>>>>>>> Press any key to continue... >>>>>>>> >>>>>>>> >>>>>>>> >>>>>>>> Regards >>>>>>>> >>>>>>>> >>>>>> Can I repair this somehow without writing the full image ? only by >>>>>> reversing the commits ? >>>>> No, not at the moment. I'm trying to figure out best way to update grub >>>>> on sysupgrade, until then reverting the mentioned commits will bring back >>>>> old behavior, and no manual intervention on boot will be necessary. >>>> >>>> shall we revert the series ? >>> Yes, but not the whole series only these commits: >>> >>> 546fced2a23557e95dd34246744c3aa6cad92fe6 x86: add intel microcode entries >>> to grub config >>> 022ffb56b2491fd7d8051ac6e6c7622ecc313d8f intel-microcode: create early load >>> microcode image >>> a822283c7e56bb3b409712e0eb9af5a91aac247d x86: add amd microcode entries to >>> grub config >>> 975019b3a755ec3b91864b60b45e5ee104075096 amd64-microcode: create early load >>> microcode image >>> >>> The rest is okay, won't cause any regressions and will save the effort. >>> >>> Thank You. >>> >> done .... >> >> >> >> _______________________________________________ >> openwrt-devel mailing list >> openwrt-devel@lists.openwrt.org >> https://lists.openwrt.org/mailman/listinfo/openwrt-devel > > turns out that grub will boot automatically after a time out despite the > errors (some seconds), but there was another problem that didn't kept the > sysupgrade settings and that made my system ureachable
Yes, but still I think this error is unacceptable. Sorry about the sysupgrade problem, and thanks for the report. > > > Regards > -- TMN _______________________________________________ openwrt-devel mailing list openwrt-devel@lists.openwrt.org https://lists.openwrt.org/mailman/listinfo/openwrt-devel
