Hello Karl, On 10.11.18 18:06, Karl-Felix Glatzer wrote: > This patch adds support for TP-Link Archer A7 > > Specification: > - SOC: QCA9563 > - Flash: 16 MiB (SPI) > - RAM: 128 MiB (DDR2) > - Ethernet: 4x 1Gbps LAN + 1x 1Gbps WAN > - Wireless: > - 2.4GHz (bgn) SoC internal > - 5GHz (ac) QCA988x > - USB: 1x USB 2.0 port > - Button: 1x power, 1x reset, 1x wps > - LED: 10x LEDs > - UART: holes in PCB > - Vcc, GND, RX, TX from ethernet port side > - 115200n8 > > Flash instruction using factory image: > > 1. Connect the computer to one of the LAN ports of the Archer A7 > 2. Set the computer IP to 192.168.0.66 > 3. Start a tftp server with the OpenWrt factory image in the tftp > root directory renamed to ArcherC7v5_tp_recovery.bin > 2. Connect power cable to Archer A7, press and hold the reset button > and turn the router on > 3. Keep the reset button pressed for ~5 seconds > 4. Wait ~150 seconds to complete flashing
Does it really only accept the firmware by TFTP and blocks installation thru the TP-Link UI? Also the filename seems odd, although completely possible TP-Link uses the C7 filename. > Signed-off-by: Karl-Felix Glatzer <karl.glat...@gmx.de> > --- > .../ath79/base-files/etc/board.d/01_leds | 7 + > .../ath79/base-files/etc/board.d/02_network | 4 + > .../etc/hotplug.d/firmware/11-ath10k-caldata | 1 + > .../ath79/dts/qca9563_tplink_archer-a7-v5.dts | 255 ++++++++++++++++++ > target/linux/ath79/image/common-tp-link.mk | 9 + > target/linux/ath79/image/generic-tp-link.mk | 16 ++ > tools/firmware-utils/src/tplink-safeloader.c | 46 +++- > 7 files changed, 337 insertions(+), 1 deletion(-) > create mode 100644 target/linux/ath79/dts/qca9563_tplink_archer-a7-v5.dts > > diff --git a/target/linux/ath79/base-files/etc/board.d/01_leds > b/target/linux/ath79/base-files/etc/board.d/01_leds > index f04eb7f5c6..4ddf04ef84 100755 > --- a/target/linux/ath79/base-files/etc/board.d/01_leds > +++ b/target/linux/ath79/base-files/etc/board.d/01_leds > @@ -57,6 +57,13 @@ tplink,tl-mr3020-v1|\ > tplink,tl-mr3040-v2) > ucidef_set_led_netdev "lan" "LAN" "tp-link:green:lan" "eth0" > ;; > +tplink,archer-a7-v5) > + ucidef_set_led_switch "wan" "WAN" "tp-link:green:wan" "switch0" "0x02" > + ucidef_set_led_switch "lan1" "LAN1" "tp-link:green:lan1" "switch0" > "0x04" > + ucidef_set_led_switch "lan2" "LAN2" "tp-link:green:lan2" "switch0" > "0x08" > + ucidef_set_led_switch "lan3" "LAN3" "tp-link:green:lan3" "switch0" > "0x10" > + ucidef_set_led_switch "lan4" "LAN4" "tp-link:green:lan4" "switch0" > "0x20" > + ;; > tplink,tl-wr1043nd-v4) > ucidef_set_led_switch "wan" "WAN" "tp-link:green:wan" "switch0" "0x20" > ucidef_set_led_switch "lan1" "LAN1" "tp-link:green:lan1" "switch0" > "0x10" > diff --git a/target/linux/ath79/base-files/etc/board.d/02_network > b/target/linux/ath79/base-files/etc/board.d/02_network > index 5f02c5769a..7c7c9e14e1 100755 > --- a/target/linux/ath79/base-files/etc/board.d/02_network > +++ b/target/linux/ath79/base-files/etc/board.d/02_network > @@ -107,6 +107,10 @@ ath79_setup_interfaces() > ucidef_add_switch "switch0" \ > "0@eth0" "3:lan:1" "5:lan:2" "4:wan" > ;; > + tplink,archer-a7-v5) > + ucidef_add_switch "switch0" \ > + "0@eth0" "2:lan:1" "3:lan:2" "4:lan:3" "5:lan:4" "1:wan" > + ;; > tplink,archer-c7-v1|\ > tplink,archer-c7-v2|\ > tplink,tl-wdr4900-v2) > diff --git > a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata > b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata > index dfe2d3ef31..6001df07bb 100644 > --- a/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata > +++ b/target/linux/ath79/base-files/etc/hotplug.d/firmware/11-ath10k-caldata > @@ -100,6 +100,7 @@ case "$FIRMWARE" in > ath10kcal_extract "ART" 20480 2116 > ath10kcal_patch_mac $(macaddr_add $(cat > /sys/class/net/eth0/address) +16) > ;; > + tplink,archer-a7-v5|\ > tplink,archer-c7-v2) > ath10kcal_extract "art" 20480 2116 > ath10kcal_patch_mac $(macaddr_add $(cat > /sys/class/net/eth1/address) -1) > diff --git a/target/linux/ath79/dts/qca9563_tplink_archer-a7-v5.dts > b/target/linux/ath79/dts/qca9563_tplink_archer-a7-v5.dts > new file mode 100644 > index 0000000000..c62cb63b0d > --- /dev/null > +++ b/target/linux/ath79/dts/qca9563_tplink_archer-a7-v5.dts > @@ -0,0 +1,255 @@ > +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT > +/dts-v1/; > + > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/input/input.h> > + > +#include "qca956x.dtsi" > + > +/ { > + compatible = "tplink,archer-a7-v5", "qca,qca9563"; > + model = "TP-Link Archer A7 Version 5"; This might e a bit of personal preference, but TP-Link never calls their Devices "XXX Version Y", so i would go for "TP-Link Archer A7 v5", as everywhere else it is referenced as such (see the image Makefile for example), but i would appreciate a second opinion about this topic. https://github.com/openwrt/openwrt/pull/1501#discussion_r228745576 > + > + chosen { > + bootargs = "console=ttyS0,115200n8"; > + }; > + > + aliases { > + led-status = &system; > + }; > + > + gpio_leds: leds { > + compatible = "gpio-leds"; > + > + system: system { > + label = "tp-link:green:system"; > + gpios = <&gpio 6 GPIO_ACTIVE_LOW>; > + default-state = "on"; > + }; > + > + led_wlan2g: wlan2g { > + label = "tp-link:green:wlan2g"; > + gpios = <&gpio 14 GPIO_ACTIVE_LOW>; > + default-state = "off"; > + linux,default-trigger = "phy1tpt"; > + }; > + > + usb { > + label = "tp-link:green:usb"; > + gpios = <&gpio 7 GPIO_ACTIVE_LOW>; > + default-state = "off"; > + trigger-sources = <&hub_port0>; > + linux,default-trigger = "usbport"; > + }; > + }; > + > + gpio_keys: keys { > + compatible = "gpio-keys"; > + > + reset { > + label = "Reset button"; > + linux,code = <KEY_RESTART>; > + gpios = <&gpio 11 GPIO_ACTIVE_LOW>; > + debounce-interval = <60>; > + }; > + > + wps { > + label = "WPS button"; > + linux,code = <KEY_WPS_BUTTON>; > + gpios = <&gpio 2 GPIO_ACTIVE_LOW>; > + debounce-interval = <60>; > + }; > + }; > + > + gpio-export { > + compatible = "gpio-export"; > + > + gpio_usb_power { > + gpio-export,name = "tp-link:power:usb"; > + gpio-export,output = <1>; > + gpios = <&gpio 19 GPIO_ACTIVE_HIGH>; > + }; > + }; > +}; > + > +&pcie { > + status = "okay"; > +}; > + > +&uart { > + status = "okay"; > +}; > + > +&gpio { > + status = "okay"; > +}; > + > +&usb_phy0 { > + status = "okay"; > +}; > + > +&usb0 { > + #address-cells = <1>; > + #size-cells = <0>; > + status = "okay"; > + > + hub_port0: port@1 { > + reg = <1>; > + #trigger-source-cells = <0>; > + }; > +}; > + > +&gpio_leds { > + wlan5g { > + label = "tp-link:green:wlan5g"; > + gpios = <&gpio 9 GPIO_ACTIVE_LOW>; > + default-state = "off"; > + linux,default-trigger = "phy0tpt"; > + }; > + > + wan { > + label = "tp-link:green:wan"; > + gpios = <&gpio 21 GPIO_ACTIVE_LOW>; > + default-state = "off"; > + }; > + > + wan_fail { > + label = "tp-link:orange:wan"; > + gpios = <&gpio 20 GPIO_ACTIVE_LOW>; > + default-state = "off"; > + }; > + > + lan1 { > + label = "tp-link:green:lan1"; > + gpios = <&gpio 8 GPIO_ACTIVE_LOW>; > + default-state = "off"; > + }; > + > + lan2 { > + label = "tp-link:green:lan2"; > + gpios = <&gpio 17 GPIO_ACTIVE_LOW>; > + default-state = "off"; > + }; > + > + lan3 { > + label = "tp-link:green:lan3"; > + gpios = <&gpio 16 GPIO_ACTIVE_LOW>; > + default-state = "off"; > + }; > + > + lan4 { > + label = "tp-link:green:lan4"; > + gpios = <&gpio 15 GPIO_ACTIVE_LOW>; > + default-state = "off"; > + }; > + > + wps { > + label = "tp-link:green:wps"; > + gpios = <&gpio 1 GPIO_ACTIVE_LOW>; > + default-state = "off"; > + }; > +}; > + > +&spi { > + status = "okay"; > + num-cs = <1>; > + > + flash@0 { > + compatible = "jedec,spi-nor"; > + reg = <0>; > + spi-max-frequency = <25000000>; > + > + mtdparts: partitions { > + compatible = "fixed-partitions"; > + #address-cells = <1>; > + #size-cells = <1>; > + }; > + }; > +}; > + > +&mdio0 { > + status = "okay"; > + > + phy-mask = <0>; > + > + phy0: ethernet-phy@0 { > + reg = <0>; > + phy-mode = "sgmii"; > + > + qca,ar8327-initvals = < > + 0x04 0x00080080 /* PORT0 PAD MODE CTRL */ > + 0x10 0x81000080 /* POWER_ON_STRIP */ > + 0x50 0xcc35cc35 /* LED_CTRL0 */ > + 0x54 0xcb37cb37 /* LED_CTRL1 */ > + 0x58 0x00000000 /* LED_CTRL2 */ > + 0x5c 0x00f3cf00 /* LED_CTRL3 */ > + 0x7c 0x0000007e /* PORT0_STATUS */ > + >; > + }; > +}; > + > +ð0 { > + status = "okay"; > + > + pll-data = <0x03000101 0x00000101 0x00001919>; > + > + phy-mode = "sgmii"; > + mtd-mac-address = <&info 0x8>; > + phy-handle = <&phy0>; > +}; > + > +&wmac { > + status = "okay"; > + mtd-cal-data = <&art 0x1000>; > + mtd-mac-address = <&info 0x8>; > +}; > + > +&mtdparts { > + factory-uboot@0 { > + label = "factory-uboot"; > + reg = <0x000000 0x020000>; > + read-only; > + }; > + > + uboot: u-boot@0 { > + label = "u-boot"; > + reg = <0x020000 0x020000>; > + read-only; > + }; > + > + kernel: kernel@0 { > + label = "kernel"; > + reg = <0x040000 0x190000>; > + }; > + > + rootfs: rootfs@0 { > + label = "rootfs"; > + reg = <0x1d0000 0xd30000>; > + }; > + > + info: info@f40000 { > + label = "info"; > + reg = <0xf40000 0x020000>; > + }; > + > + config: config@f60000 { > + label = "config"; > + reg = <0xf60000 0x050000>; > + }; > + > + partition@fc0000 { > + label = "partition-table"; > + reg = <0xfc0000 0x010000>; > + }; > + > + firmware@40000 { > + label = "firmware"; > + reg = <0x040000 0xec0000>; > + }; > + > + art: art@ff0000 { > + label = "art"; > + reg = <0xff0000 0x010000>; > + read-only; > + }; > +}; Looking at the Github pull-request for the ar71xx based Archer A7 v5, the C7 v5 only differs in the partitioning so we should probably put common stuff into a 'qca9563_tplink_archer-x7-v5.dts' as support for the Archer C7 v5 is most likely to be added too. https://github.com/openwrt/openwrt/pull/1462 > diff --git a/target/linux/ath79/image/common-tp-link.mk > b/target/linux/ath79/image/common-tp-link.mk > index 7490aeb1f3..4a29459196 100644 > --- a/target/linux/ath79/image/common-tp-link.mk > +++ b/target/linux/ath79/image/common-tp-link.mk > @@ -39,6 +39,15 @@ define Build/mktplinkfw-combined > @mv $@.new $@ > endef > > +define Build/uImageArcher > + ${STAGING_DIR_HOST}/bin/mkimage \ > + -A $(LINUX_KARCH) \ > + -O linux -T kernel \ > + -C $(1) -a $(KERNEL_LOADADDR) -e $(if > $(KERNEL_ENTRY),$(KERNEL_ENTRY),$(KERNEL_LOADADDR)) \ > + -n '$(call toupper,$(LINUX_KARCH)) OpenWrt > Linux-$(LINUX_VERSION)' -d $@ $@.new > + @mv $@.new $@ > +endef > + > define Device/tplink > TPLINK_HWREV := 0x1 > TPLINK_HEADER_VERSION := 1 > diff --git a/target/linux/ath79/image/generic-tp-link.mk > b/target/linux/ath79/image/generic-tp-link.mk > index d65e29e72a..d24222e9e3 100644 > --- a/target/linux/ath79/image/generic-tp-link.mk > +++ b/target/linux/ath79/image/generic-tp-link.mk > @@ -1,5 +1,21 @@ > include ./common-tp-link.mk > > +define Device/tplink_archer-a7-v5 > + $(Device/tplink) > + ATH_SOC := qca9563 > + DEVICE_TITLE := TP-LINK Archer A7 v5 > + DEVICE_PACKAGES := kmod-usb-core kmod-usb2 kmod-usb-ledtrig-usbport > kmod-ath10k ath10k-firmware-qca988x > + SUPPORTED_DEVICES := tplink,archer-a7-v5 > + BOARDNAME := ARCHER-A7-V5 > + TPLINK_BOARD_ID := ARCHER-A7-V5 > + IMAGE_SIZE := 15104k > + KERNEL := kernel-bin | append-dtb | lzma | uImageArcher lzma > + IMAGE/sysupgrade.bin := append-rootfs | tplink-safeloader sysupgrade | \ > + append-metadata | check-size $$$$(IMAGE_SIZE) > + IMAGE/factory.bin := append-rootfs | tplink-safeloader factory > +endef > +TARGET_DEVICES += tplink_archer-a7-v5 > + > define Device/tplink_archer-c7-v1 > $(Device/tplink-8mlzma) > ATH_SOC := qca9558 > diff --git a/tools/firmware-utils/src/tplink-safeloader.c > b/tools/firmware-utils/src/tplink-safeloader.c > index a51cca476e..7fa0a313d4 100644 > --- a/tools/firmware-utils/src/tplink-safeloader.c > +++ b/tools/firmware-utils/src/tplink-safeloader.c > @@ -357,6 +357,50 @@ static struct device_info boards[] = { > .last_sysupgrade_partition = "file-system" > }, > > + /** Firmware layout for the A7-V5 */ > + { > + .id = "ARCHER-A7-V5", > + .support_list = > + "SupportList:\n" > + "{product_name:Archer > A7,product_ver:5.0.0,special_id:45550000}\n" > + "{product_name:Archer > A7,product_ver:5.0.0,special_id:55530000}\n" > + "{product_name:Archer > A7,product_ver:5.0.0,special_id:43410000}\n" > + "{product_name:Archer > A7,product_ver:5.0.0,special_id:4A500000}\n" > + "{product_name:Archer > A7,product_ver:5.0.0,special_id:54570000}\n", > + .support_trail = '\x00', > + .soft_ver = "soft_ver:1.0.0\n", > + > + /** > + We use a bigger os-image partition than the stock images > (and thus > + smaller file-system), as our kernel doesn't fit in the > stock firmware's > + 1MB os-image. > + */ > + .partitions = { > + {"factory-boot", 0x00000, 0x20000}, > + {"fs-uboot", 0x20000, 0x20000}, > + {"os-image", 0x40000, 0x190000}, /* Stock: base > 0x40000 size 0x120000 */ > + {"file-system", 0x1d0000, 0xd30000}, /* Stock: base > 0x160000 size 0xda0000 */ We should use dynamic partitioning here, as the kernel size is going to increase in the future. Take a look at this commit: https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=7c78be1b747eb0c8d64da67deb3a8aec75bd7b9c Best wishes David > + {"default-mac", 0xf40000, 0x00200}, > + {"pin", 0xf40200, 0x00200}, > + {"device-id", 0xf40400, 0x00100}, > + {"product-info", 0xf40500, 0x0fb00}, > + {"soft-version", 0xf50000, 0x00100}, > + {"extra-para", 0xf51000, 0x01000}, > + {"support-list", 0xf52000, 0x0a000}, > + {"profile", 0xf5c000, 0x04000}, > + {"default-config", 0xf60000, 0x10000}, > + {"user-config", 0xf70000, 0x40000}, > + {"certificate", 0xfb0000, 0x10000}, > + {"partition-table", 0xfc0000, 0x10000}, > + {"log", 0xfd0000, 0x20000}, > + {"radio", 0xff0000, 0x10000}, > + {NULL, 0, 0} > + }, > + > + .first_sysupgrade_partition = "os-image", > + .last_sysupgrade_partition = "file-system", > + }, > + > /** Firmware layout for the C25v1 */ > { > .id = "ARCHER-C25-V1", > @@ -1577,7 +1621,7 @@ static void build_image(const char *output, > strcasecmp(info->id, "TLWR1043NV5") == 0) { > const char mdat[11] = {0x00, 0x00, 0x00, 0x02, 0x00, 0x00, > 0x00, 0x00, 0x01, 0x00, 0x00}; > parts[5] = put_data("extra-para", mdat, 11); > - } else if (strcasecmp(info->id, "ARCHER-C7-V4") == 0 || > strcasecmp(info->id, "ARCHER-C7-V5") == 0) { > + } else if (strcasecmp(info->id, "ARCHER-A7-V5") == 0 || > strcasecmp(info->id, "ARCHER-C7-V4") == 0 || strcasecmp(info->id, > "ARCHER-C7-V5") == 0) { > const char mdat[11] = {0x01, 0x00, 0x00, 0x02, 0x00, 0x00, > 0xca, 0x00, 0x01, 0x00, 0x00}; > parts[5] = put_data("extra-para", mdat, 11); > } > _______________________________________________ openwrt-devel mailing list openwrt-devel@lists.openwrt.org https://lists.openwrt.org/mailman/listinfo/openwrt-devel