if you use country 00, txpower is not limtied even without the patch. i
don't know anything about the patch and how it works. but on my <3 tplink
4900 (mpc85xx target) i get with 00
iwinfo phy1 txpowerlist
0 dBm ( 1 mW)
1 dBm ( 1 mW)
2 dBm ( 1 mW)
3 dBm ( 1 mW)
4 dBm ( 2 mW)
5 dBm ( 3 mW)
6 dBm ( 3 mW)
7 dBm ( 5 mW)
8 dBm ( 6 mW)
9 dBm ( 7 mW)
10 dBm ( 10 mW)
11 dBm ( 12 mW)
12 dBm ( 15 mW)
13 dBm ( 19 mW)
14 dBm ( 25 mW)
15 dBm ( 31 mW)
16 dBm ( 39 mW)
17 dBm ( 50 mW)
18 dBm ( 63 mW)
19 dBm ( 79 mW)
20 dBm ( 100 mW)
21 dBm ( 125 mW)
22 dBm ( 158 mW)
23 dBm ( 199 mW)
24 dBm ( 251 mW)
* 25 dBm ( 316 mW)
iw phy1 info
Wiphy phy1
max # scan SSIDs: 4
max scan IEs length: 2257 bytes
max # sched scan SSIDs: 0
max # match sets: 0
max # scan plans: 1
max scan plan interval: -1
max scan plan iterations: 0
Retry short limit: 7
Retry long limit: 4
Coverage class: 0 (up to 0m)
Device supports AP-side u-APSD.
Device supports T-DLS.
Available Antennas: TX 0x7 RX 0x7
Configured Antennas: TX 0x7 RX 0x7
Supported interface modes:
* IBSS
* managed
* AP
* AP/VLAN
* monitor
* mesh point
* P2P-client
* P2P-GO
* outside context of a BSS
Band 1:
Capabilities: 0x11ef
RX LDPC
HT20/HT40
SM Power Save disabled
RX HT20 SGI
RX HT40 SGI
TX STBC
RX STBC 1-stream
Max AMSDU length: 3839 bytes
DSSS/CCK HT40
Maximum RX AMPDU length 65535 bytes (exponent: 0x003)
Minimum RX AMPDU time spacing: 8 usec (0x06)
HT TX/RX MCS rate indexes supported: 0-23
Frequencies:
* 2412 MHz [1] (25.0 dBm)
* 2417 MHz [2] (25.0 dBm)
* 2422 MHz [3] (25.0 dBm)
* 2427 MHz [4] (25.0 dBm)
* 2432 MHz [5] (25.0 dBm)
* 2437 MHz [6] (25.0 dBm)
* 2442 MHz [7] (25.0 dBm)
* 2447 MHz [8] (25.0 dBm)
* 2452 MHz [9] (25.0 dBm)
* 2457 MHz [10] (25.0 dBm)
* 2462 MHz [11] (25.0 dBm)
* 2467 MHz [12] (disabled)
* 2472 MHz [13] (disabled)
* 2484 MHz [14] (disabled)
valid interface combinations:
* #{ managed } <= 2048, #{ AP, mesh point } <= 8, #{ P2P-client,
P2P-GO } <= 1, #{ IBSS } <= 1,
total <= 2048, #channels <= 1, STA/AP BI must match, radar
detect widths: { 20 MHz (no HT), 20 MHz, 40 MHz }
HT Capability overrides:
* MCS: ff ff ff ff ff ff ff ff ff ff
* maximum A-MSDU length
* supported channel width
* short GI for 40 MHz
* max A-MPDU length exponent
* min MPDU start spacing
so i don't think the patch is working @all ...
cheers
2017-07-20 23:52 GMT+02:00 Jenny Cabrera Varona <jenny.cabr...@reduc.edu.cu>
:
> > you are probably using outdated patch
> >
>
> Tom Psyborg:
> patch it's working well i test it manually and it works, right now i just
> have troubles to get 2312-2732 MHz frequencies, tx power already unlocked,
> using country 00 i can set channels from 1-14 ...
>
> what i need to do for 2312-2732 MHz
> thanks for all
>
> ------------------------------------------------------------
> -------------------
> ---- Universidad de Camagüey "Ignacio Agramonte Loynaz", Cuba
> ----------------
> ------------------------------------------------------------
> -------------------
> ---- 6 de noviembre de 2017 ------------------------------
> ------------------
> ----- Aniversario 50 de la Universidad de Camagüey "Ignacio Agramonte
> Loynaz"-
> ---- "50 años de ciencia y compromiso" ------------------------------
> ---------
> ------------------------------------------------------------
> -------------------
> ---- Aniversario 95 de la FEU ------------------------------
> -------------------
> ---- https://www.reduc.edu.cu/ ------------------------------
> ------------------
> ------------------------------------------------------------
> -------------------
> _______________________________________________
> openwrt-devel mailing list
> openwrt-devel@lists.openwrt.org
> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
>
_______________________________________________
openwrt-devel mailing list
openwrt-devel@lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
