2016-03-16 14:46 GMT+01:00 John Crispin <j...@phrozen.org>: > > > On 16/03/2016 14:25, Baptiste Clenet wrote: >> 2016-03-07 15:19 GMT+01:00 John Crispin <blo...@openwrt.org>: >>> >>> >>> On 07/03/2016 15:00, Baptiste Clenet wrote: >>>> 2016-03-07 9:51 GMT+01:00 John Crispin <j...@phrozen.org>: >>>>> >>>>> >>>>> On 07/03/2016 09:47, Baptiste Clenet wrote: >>>>>> 2016-03-04 18:24 GMT+01:00 John Crispin <j...@phrozen.org>: >>>>>>> >>>>>>> >>>>>>> On 04/03/2016 17:50, Baptiste Clenet wrote: >>>>>>>> We don't use the current tree but a version from November. >>>>>>>> You're talking about this changeset: >>>>>>>> https://dev.openwrt.org/changeset/48749 >>>>>>>> >>>>>>>> I will apply it and let you know if it is better. >>>>>>>> >>>>>>>>>>>> >>>>>>> >>>>>>> >>>>>>> yep, try adding that one please and see if that fixes the issue >>>>>>> _______________________________________________ >>>>>>> openwrt-devel mailing list >>>>>>> openwrt-devel@lists.openwrt.org >>>>>>> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel >>>>>> >>>>>> John, I chose Default profile for mt7688 board and it has built an >>>>>> image named "openwrt-ramips-mt7688-LinkIt7688-squashfs-sysupgrade.bin", >>>>>> so it used the LINKIT7688 dts instead of MT7628 dts. >>>>>> >>>>>> Concerning USB, I see the same behaviour, if the pendrive is plugged >>>>>> between the boot, it works and I can plug it in and out as much as I >>>>>> can, however, it the board boots and then I insert the pendrive, it is >>>>>> not detected (the pendrive's led switches on for 1/2sec and then >>>>>> switches off. >>>>> >>>>> seen this before while building pcbs .. so my money is on the following >>>>> theory: your power supply is failing to provide enough current quickly >>>>> enough for the USB to come up causing OC protection or similar to shut >>>>> it down. check your supply voltage of the usb port with a scope and you >>>>> will probably see it breakdown after that 1/2 s >>>> >>>> Yes it was a hardware problem effectively, I added a protection chip >>>> which did not work properly and caused the pendrive not to be >>>> detected. I removed it and it works, so I will dig into the hardware >>>> problem. >>>> Thanks >>> >>> we are a software project so awesome we can even remote debug hardware >>> problems :-) >>> >>> >>>>> >>>>> >>>>> >>>>> >>>>>> Second question; I see you added the mt76 wifi driver which is great! >>>>>> Thank you for your work. I see the module added on the board, how may >>>>>> I up the wifi? (I didn't find any readme on github [1]) >>>>> >>>>> its a normal mac80211 based wifi so use the normal method. you will need >>>>> to add a eeprom offset to the dts file. either figure it out yourself >>>>> (look at how mt7620 based boards do it) or wait a few days till i had >>>>> time to update the lks7688 profile. >> >> John, have you had time to update mt7688 board for wifi setup? >> > > let me check the commit log for you ... > > ... nope i cant find a commit that adds the support ;) i hope to have > time start of next week. > Ok, could you let me know when you're done with that please? Thanks >>>>> >>>> I let you do the edits and I will try as soon as you've done it. >>>> Thanks for your help >>> >>> ok >> >> >>
-- Baptiste _______________________________________________ openwrt-devel mailing list openwrt-devel@lists.openwrt.org https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
