nope that did not work properly. please consider using git to send the patch
--> https://patchwork.ozlabs.org/patch/560543/ On 23/12/2015 14:12, Tathagata Das wrote: > Hi John, > > Please check the content of the patch below. > > > ---------------------------------------------- > Index: trunk/target/linux/ipq806x/image/Makefile > =================================================================== > --- trunk/target/linux/ipq806x/image/Makefile (revision 47890) > +++ trunk/target/linux/ipq806x/image/Makefile (working copy) > @@ -121,6 +121,17 @@y. > BOARD_NAME := r7500 > endef > > -TARGET_DEVICES += AP148 AP148-legacy DB149 R7500 > +define Device/D7800 > + $(call Device/DniImage) > + DEVICE_DTS := qcom-ipq8064-d7800 > + KERNEL_SIZE := 2097152 > + NETGEAR_BOARD_ID := D7800 > + NETGEAR_HW_ID := 29764958+0+128+512+4x4+4x4 > + BLOCKSIZE := 128KiB > + PAGESIZE := 2048 > + BOARD_NAME := d7800 > +endef > > +TARGET_DEVICES += AP148 AP148-legacy DB149 R7500 D7800 > + > $(eval $(call BuildImage)) > Index: trunk/target/linux/ipq806x/profiles/netgear.mk > =================================================================== > --- trunk/target/linux/ipq806x/profiles/netgear.mk (revision 47890) > +++ trunk/target/linux/ipq806x/profiles/netgear.mk (working copy) > @@ -17,4 +17,18 @@ > define Profile/R7500/Description > Package set for the Netgear Nighthawk X4 R7500. > endef > + > +define Profile/D7800 > + NAME:=Netgear Nighthawk X4 D7800 > + PACKAGES:= \ > + kmod-usb-core kmod-usb-ohci kmod-usb2 kmod-ledtrig-usbdev \ > + kmod-usb3 kmod-usb-dwc3-qcom kmod-usb-phy-qcom-dwc3 \ > + kmod-ath10k wpad-mini ath10k-firmware-qca99x0 > +endef > + > +define Profile/D7800/Description > + Package set for the Netgear Nighthawk X4 D7800. > +endef > + > $(eval $(call Profile,R7500)) > +$(eval $(call Profile,D7800)) > Index: trunk/target/linux/ipq806x/base-files/lib/upgrade/platform.sh > =================================================================== > --- trunk/target/linux/ipq806x/base-files/lib/upgrade/platform.sh > (revision 47890) > +++ trunk/target/linux/ipq806x/base-files/lib/upgrade/platform.sh > (working copy) > @@ -7,7 +7,8 @@ > > case "$board" in > AP148 |\ > - r7500) > + r7500 |\ > + d7800) > nand_do_platform_check $board $1 > return $?; > ;; > @@ -21,7 +22,8 @@ > > case "$board" in > AP148 |\ > - r7500) > + r7500 |\ > + d7800) > nand_do_upgrade "$1" > ;; > esac > Index: trunk/target/linux/ipq806x/base-files/lib/ipq806x.sh > =================================================================== > --- trunk/target/linux/ipq806x/base-files/lib/ipq806x.sh (revision > 47890) > +++ trunk/target/linux/ipq806x/base-files/lib/ipq806x.sh (working > copy) > @@ -23,6 +23,9 @@ > *"R7500") > name="r7500" > ;; > + *"D7800") > + name="d7800" > + ;; > esac > > [ -z "$name" ] && name="unknown" > Index: trunk/target/linux/ipq806x/base-files/etc/board.d/01_leds > =================================================================== > --- trunk/target/linux/ipq806x/base-files/etc/board.d/01_leds (revision > 47890) > +++ trunk/target/linux/ipq806x/base-files/etc/board.d/01_leds (working > copy) > @@ -11,7 +11,8 @@ > board=$(ipq806x_board_name) > > case "$board" in > -r7500) > +r7500 |\ > +d7800) > ucidef_set_led_usbdev "usb1" "USB 1" "r7500:white:usb1" "1-1" > ucidef_set_led_usbdev "usb2" "USB 2" "r7500:white:usb3" "3-1" > ucidef_set_led_netdev "wan" "WAN" "r7500:white:wan" "eth0" > Index: trunk/target/linux/ipq806x/base-files/etc/board.d/02_network > =================================================================== > --- trunk/target/linux/ipq806x/base-files/etc/board.d/02_network > (revision 47890) > +++ trunk/target/linux/ipq806x/base-files/etc/board.d/02_network > (working copy) > @@ -13,7 +13,8 @@ > > case "$board" in > ap148 |\ > -r7500) > +r7500 |\ > +d7800) > ucidef_add_switch "switch0" \ > "1:lan" "2:lan" "3:lan" "4:lan" "6@eth1" "5:wan" "0@eth0" > ;; > Index: > trunk/target/linux/ipq806x/patches-3.18/801-ARM-qcom-add-Netgear-Nighthawk-X > 4-D7800-device-tree.patch > =================================================================== > --- > trunk/target/linux/ipq806x/patches-3.18/801-ARM-qcom-add-Netgear-Nighthawk-X > 4-D7800-device-tree.patch (revision 0) > +++ > trunk/target/linux/ipq806x/patches-3.18/801-ARM-qcom-add-Netgear-Nighthawk-X > 4-D7800-device-tree.patch (revision 0) > @@ -0,0 +1,381 @@ > +--- a/arch/arm/boot/dts/Makefile 2015-09-22 18:30:09.033530282 +0530 > ++++ b/arch/arm/boot/dts/Makefile 2015-09-23 17:06:44.892947581 +0530 > +@@ -362,6 +362,7 @@ > + qcom-ipq8064-ap148.dtb \ > + qcom-ipq8064-db149.dtb \ > + qcom-ipq8064-r7500.dtb \ > ++ qcom-ipq8064-d7800.dtb \ > + qcom-msm8660-surf.dtb \ > + qcom-msm8960-cdp.dtb \ > + qcom-msm8974-sony-xperia-honami.dtb > +--- a/arch/arm/boot/dts/qcom-ipq8064-d7800.dts 1970-01-01 > 05:30:00.000000000 +0530 > ++++ b/arch/arm/boot/dts/qcom-ipq8064-d7800.dts 2015-09-23 > 17:06:45.336947567 +0530 > +@@ -0,0 +1,368 @@ > ++#include "qcom-ipq8064-v1.0.dtsi" > ++ > ++#include <dt-bindings/input/input.h> > ++ > ++/ { > ++ model = "Netgear Nighthawk X4 D7800"; > ++ compatible = "netgear,d7800", "qcom,ipq8064"; > ++ > ++ memory@0 { > ++ reg = <0x42000000 0xe000000>; > ++ device_type = "memory"; > ++ }; > ++ > ++ reserved-memory { > ++ #address-cells = <1>; > ++ #size-cells = <1>; > ++ ranges; > ++ rsvd@41200000 { > ++ reg = <0x41200000 0x300000>; > ++ no-map; > ++ }; > ++ }; > ++ > ++ aliases { > ++ serial0 = &uart4; > ++ mdio-gpio0 = &mdio0; > ++ }; > ++ > ++ chosen { > ++ bootargs = "rootfstype=squashfs noinitrd"; > ++ linux,stdout-path = "serial0:115200n8"; > ++ }; > ++ > ++ soc { > ++ pinmux@800000 { > ++ i2c4_pins: i2c4_pinmux { > ++ pins = "gpio12", "gpio13"; > ++ function = "gsbi4"; > ++ bias-disable; > ++ }; > ++ > ++ pcie0_pins: pcie0_pinmux { > ++ mux { > ++ pins = "gpio3"; > ++ function = "pcie1_rst"; > ++ drive-strength = <12>; > ++ bias-disable; > ++ }; > ++ }; > ++ > ++ pcie1_pins: pcie1_pinmux { > ++ mux { > ++ pins = "gpio48"; > ++ function = "pcie2_rst"; > ++ drive-strength = <12>; > ++ bias-disable; > ++ }; > ++ }; > ++ > ++ nand_pins: nand_pins { > ++ mux { > ++ pins = "gpio34", "gpio35", "gpio36", > ++ "gpio37", "gpio38", "gpio39", > ++ "gpio40", "gpio41", "gpio42", > ++ "gpio43", "gpio44", "gpio45", > ++ "gpio46", "gpio47"; > ++ function = "nand"; > ++ drive-strength = <10>; > ++ bias-disable; > ++ }; > ++ pullups { > ++ pins = "gpio39"; > ++ bias-pull-up; > ++ }; > ++ hold { > ++ pins = "gpio40", "gpio41", "gpio42", > ++ "gpio43", "gpio44", "gpio45", > ++ "gpio46", "gpio47"; > ++ bias-bus-hold; > ++ }; > ++ }; > ++ > ++ mdio0_pins: mdio0_pins { > ++ mux { > ++ pins = "gpio0", "gpio1"; > ++ function = "gpio"; > ++ drive-strength = <8>; > ++ bias-disable; > ++ }; > ++ }; > ++ > ++ rgmii2_pins: rgmii2_pins { > ++ mux { > ++ pins = "gpio27", "gpio28", "gpio29", > "gpio30", "gpio31", "gpio32", > ++ "gpio51", "gpio52", "gpio59", > "gpio60", "gpio61", "gpio62" ; > ++ function = "rgmii2"; > ++ drive-strength = <8>; > ++ bias-disable; > ++ }; > ++ }; > ++ }; > ++ > ++ gsbi@16300000 { > ++ qcom,mode = <GSBI_PROT_I2C_UART>; > ++ status = "ok"; > ++ serial@16340000 { > ++ status = "ok"; > ++ }; > ++ /* > ++ * The i2c device on gsbi4 should not be enabled. > ++ * On ipq806x designs gsbi4 i2c is meant for > exclusive > ++ * RPM usage. Turning this on in kernel manifests as > ++ * i2c failure for the RPM. > ++ */ > ++ }; > ++ > ++ sata-phy@1b400000 { > ++ status = "ok"; > ++ }; > ++ > ++ sata@29000000 { > ++ status = "ok"; > ++ }; > ++ > ++ phy@100f8800 { /* USB3 port 1 HS phy */ > ++ status = "ok"; > ++ }; > ++ > ++ phy@100f8830 { /* USB3 port 1 SS phy */ > ++ status = "ok"; > ++ }; > ++ > ++ phy@110f8800 { /* USB3 port 0 HS phy */ > ++ status = "ok"; > ++ }; > ++ > ++ phy@110f8830 { /* USB3 port 0 SS phy */ > ++ status = "ok"; > ++ }; > ++ > ++ usb30@0 { > ++ status = "ok"; > ++ }; > ++ > ++ usb30@1 { > ++ status = "ok"; > ++ }; > ++ > ++ pcie0: pci@1b500000 { > ++ status = "ok"; > ++ reset-gpio = <&qcom_pinmux 3 0>; > ++ pinctrl-0 = <&pcie0_pins>; > ++ pinctrl-names = "default"; > ++ }; > ++ > ++ pcie1: pci@1b700000 { > ++ status = "ok"; > ++ reset-gpio = <&qcom_pinmux 48 0>; > ++ pinctrl-0 = <&pcie1_pins>; > ++ pinctrl-names = "default"; > ++ }; > ++ > ++ nand@1ac00000 { > ++ status = "ok"; > ++ > ++ pinctrl-0 = <&nand_pins>; > ++ pinctrl-names = "default"; > ++ > ++ nand-ecc-strength = <4>; > ++ nand-bus-width = <8>; > ++ > ++ #address-cells = <1>; > ++ #size-cells = <1>; > ++ > ++ qcadata@0 { > ++ label = "qcadata"; > ++ reg = <0x0000000 0x0c80000>; > ++ read-only; > ++ }; > ++ > ++ APPSBL@c80000 { > ++ label = "APPSBL"; > ++ reg = <0x0c80000 0x0500000>; > ++ read-only; > ++ }; > ++ > ++ APPSBLENV@1180000 { > ++ label = "APPSBLENV"; > ++ reg = <0x1180000 0x0080000>; > ++ read-only; > ++ }; > ++ > ++ art: art@1200000 { > ++ label = "art"; > ++ reg = <0x1200000 0x0140000>; > ++ read-only; > ++ }; > ++ > ++ artbak: art@1340000 { > ++ label = "artbak"; > ++ reg = <0x1340000 0x0140000>; > ++ read-only; > ++ }; > ++ > ++ kernel@1480000 { > ++ label = "kernel"; > ++ reg = <0x1480000 0x0200000>; > ++ }; > ++ > ++ ubi@1680000 { > ++ label = "ubi"; > ++ reg = <0x1680000 0x1E00000>; > ++ }; > ++ > ++ netgear@3480000 { > ++ label = "netgear"; > ++ reg = <0x3480000 0x4480000>; > ++ read-only; > ++ }; > ++ > ++ reserve@7900000 { > ++ label = "reserve"; > ++ reg = <0x7900000 0x0700000>; > ++ read-only; > ++ }; > ++ > ++ firmware@1480000 { > ++ label = "firmware"; > ++ reg = <0x1480000 0x2000000>; > ++ }; > ++ > ++ }; > ++ > ++ mdio0: mdio { > ++ compatible = "virtual,mdio-gpio"; > ++ #address-cells = <1>; > ++ #size-cells = <0>; > ++ gpios = <&qcom_pinmux 1 0 &qcom_pinmux 0 0>; > ++ pinctrl-0 = <&mdio0_pins>; > ++ pinctrl-names = "default"; > ++ > ++ phy0: ethernet-phy@0 { > ++ device_type = "ethernet-phy"; > ++ reg = <0>; > ++ qca,ar8327-initvals = < > ++ 0x00004 0x7600000 /* PAD0_MODE */ > ++ 0x00008 0x1000000 /* PAD5_MODE */ > ++ 0x0000c 0x80 /* PAD6_MODE */ > ++ 0x000e4 0xaa545 /* MAC_POWER_SEL > */ > ++ 0x000e0 0xc74164de /* SGMII_CTRL */ > ++ 0x0007c 0x4e /* PORT0_STATUS > */ > ++ 0x00094 0x4e /* PORT6_STATUS > */ > ++ >; > ++ }; > ++ > ++ phy4: ethernet-phy@4 { > ++ device_type = "ethernet-phy"; > ++ reg = <4>; > ++ }; > ++ }; > ++ > ++ gmac1: ethernet@37200000 { > ++ status = "ok"; > ++ phy-mode = "rgmii"; > ++ phy-handle = <&phy4>; > ++ qcom,id = <1>; > ++ > ++ pinctrl-0 = <&rgmii2_pins>; > ++ pinctrl-names = "default"; > ++ > ++ mtd-mac-address = <&art 6>; > ++ }; > ++ > ++ gmac2: ethernet@37400000 { > ++ status = "ok"; > ++ phy-mode = "sgmii"; > ++ qcom,id = <2>; > ++ > ++ mtd-mac-address = <&art 0>; > ++ > ++ fixed-link { > ++ speed = <1000>; > ++ full-duplex; > ++ }; > ++ }; > ++ }; > ++ > ++ gpio-keys { > ++ compatible = "gpio-keys"; > ++ > ++ wifi { > ++ label = "wifi"; > ++ gpios = <&qcom_pinmux 6 1>; > ++ linux,code = <KEY_WLAN>; > ++ }; > ++ > ++ reset { > ++ label = "reset"; > ++ gpios = <&qcom_pinmux 54 1>; > ++ linux,code = <KEY_RESTART>; > ++ }; > ++ > ++ wps { > ++ label = "wps"; > ++ gpios = <&qcom_pinmux 65 1>; > ++ linux,code = <KEY_WPS_BUTTON>; > ++ }; > ++ }; > ++ > ++ gpio-leds { > ++ compatible = "gpio-leds"; > ++ > ++ usb1 { > ++ label = "d7800:amber:usb1"; > ++ gpios = <&qcom_pinmux 7 0>; > ++ }; > ++ > ++ usb3 { > ++ label = "d7800:amber:usb3"; > ++ gpios = <&qcom_pinmux 8 0>; > ++ }; > ++ > ++ status { > ++ label = "d7800:amber:status"; > ++ gpios = <&qcom_pinmux 9 0>; > ++ }; > ++ > ++ internet { > ++ label = "d7800:white:internet"; > ++ gpios = <&qcom_pinmux 22 0>; > ++ }; > ++ > ++ wan { > ++ label = "d7800:white:wan"; > ++ gpios = <&qcom_pinmux 23 0>; > ++ }; > ++ > ++ wps { > ++ label = "d7800:white:wps"; > ++ gpios = <&qcom_pinmux 24 0>; > ++ }; > ++ > ++ esata { > ++ label = "d7800:white:esata"; > ++ gpios = <&qcom_pinmux 26 0>; > ++ }; > ++ > ++ power { > ++ label = "d7800:white:power"; > ++ gpios = <&qcom_pinmux 53 0>; > ++ default-state = "on"; > ++ }; > ++ > ++ rfkill { > ++ label = "d7800:white:rfkill"; > ++ gpios = <&qcom_pinmux 64 0>; > ++ }; > ++ > ++ wifi5g { > ++ label = "d7800:white:wifi5g"; > ++ gpios = <&qcom_pinmux 67 0>; > ++ }; > ++ }; > ++}; > ++ > ++&adm_dma { > ++ status = "ok"; > ++}; > > Regards, > Tathagata > > > -----Original Message----- > From: John Crispin [mailto:blo...@openwrt.org] > Sent: 23 December 2015 18:34 > To: openwrt-devel@lists.openwrt.org; Tathagata Das > Subject: Re: [OpenWrt-Devel] [Patch] ipq806x: add support for Netgear D7800 > > Hi, > > you sent the patch as an attachment. because of this patchwork did not pick > it up. could you please resend with the patch inline rather than attached. > > John > > On 14/12/2015 10:37, Tathagata Das wrote: >> Add support for the Netgear D7800 and build appropariate sysupgrade >> and factory images. >> >> Known issues: >> . USB ports are not working >> . DSL is not added >> >> Signed-off-by: Tathagata Das <tathag...@alumnux.com> >> >> >> >> _______________________________________________ >> openwrt-devel mailing list >> openwrt-devel@lists.openwrt.org >> https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel >> _______________________________________________ openwrt-devel mailing list openwrt-devel@lists.openwrt.org https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
