Sorry,
Re-send After correcting the patch.
2015-08-18 3:13 GMT+09:00 Piotr Dymacz <pep...@gmail.com>:
> Hello,
>
> Please, see my comments inline.
>
> 2015-08-17 19:20 GMT+02:00 YuheiOKAWA <tochiro.srch...@gmail.com>:
> > This patch add support for Planex DB-WRT01. DANBOARD route on
> > the MT7620A SoC with two Ethernet port and a 802.11n 2.4 GHz radio.
> > DANBOARD is Cartoon character.
> >
> > Signed-off-by: YuheiOKAWA <tochiro.srch...@gmail.com>
> > ---
> > target/linux/ramips/base-files/etc/board.d/01_leds | 3 +
> > .../linux/ramips/base-files/etc/board.d/02_network | 1 +
> > target/linux/ramips/base-files/etc/diag.sh | 1 +
> > target/linux/ramips/base-files/lib/ramips.sh | 3 +
> > .../ramips/base-files/lib/upgrade/platform.sh | 1 +
> > target/linux/ramips/dts/DB-WRT01.dts | 99
> ++++++++++++++++++++++
> > target/linux/ramips/image/Makefile | 2 +
> > 7 files changed, 110 insertions(+)
> > create mode 100644 target/linux/ramips/dts/DB-WRT01.dts
> >
> > diff --git a/target/linux/ramips/base-files/etc/board.d/01_leds
> b/target/linux/ramips/base-files/etc/board.d/01_leds
> > index 71cf3ac..a9959e3 100755
> > --- a/target/linux/ramips/base-files/etc/board.d/01_leds
> > +++ b/target/linux/ramips/base-files/etc/board.d/01_leds
> > @@ -87,6 +87,9 @@ d105)
> > ucidef_set_led_default "power" "POWER" "$board:red:power" "1"
> > set_usb_led "$board:green:usb"
> > ;;
> > +db-wrt01)
> > + ucidef_set_led_default "power" "power" "$board:orange:power" "1"
> > + ;;
> > dcs-930l-b1)
> > ucidef_set_led_default "power" "POWER" "$board:red:power" "1"
> > ucidef_set_led_netdev "wifi" "WiFi" "$board:blue:wps"
> > diff --git a/target/linux/ramips/base-files/etc/board.d/02_network
> b/target/linux/ramips/base-files/etc/board.d/02_network
> > index 6a2f042..02cd682 100755
> > --- a/target/linux/ramips/base-files/etc/board.d/02_network
> > +++ b/target/linux/ramips/base-files/etc/board.d/02_network
> > @@ -61,6 +61,7 @@ ramips_setup_interfaces()
> > ;;
> > 3g-6200n|\
> > ai-br100|\
> > + db-wrt01|\
> > dir-300-b7|\
> > dir-320-b1|\
> > dir-610-a1|\
> > diff --git a/target/linux/ramips/base-files/etc/diag.sh
> b/target/linux/ramips/base-files/etc/diag.sh
> > index a4911b0..f886b5d 100644
> > --- a/target/linux/ramips/base-files/etc/diag.sh
> > +++ b/target/linux/ramips/base-files/etc/diag.sh
> > @@ -94,6 +94,7 @@ get_status_led() {
> > y1s)
> > status_led="$board:blue:power"
> > ;;
> > + db-wrt01|\
> > esr-9753)
> > status_led="$board:orange:power"
> > ;;
> > diff --git a/target/linux/ramips/base-files/lib/ramips.sh
> b/target/linux/ramips/base-files/lib/ramips.sh
> > index 5cafd45..5b6808e 100755
> > --- a/target/linux/ramips/base-files/lib/ramips.sh
> > +++ b/target/linux/ramips/base-files/lib/ramips.sh
> > @@ -97,6 +97,9 @@ ramips_board_detect() {
> > *"DAP-1350")
> > name="dap-1350"
> > ;;
> > + *"DB-WRT01")
> > + name="db-wrt01"
> > + ;;
> > *"DCS-930")
> > name="dcs-930"
> > ;;
> > diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh
> b/target/linux/ramips/base-files/lib/upgrade/platform.sh
> > index 53e7070..844ed5d 100755
> > --- a/target/linux/ramips/base-files/lib/upgrade/platform.sh
> > +++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh
> > @@ -36,6 +36,7 @@ platform_check_image() {
> > cf-wr800n|\
> > d105|\
> > dap-1350|\
> > + db-wrt01|\
> > dcs-930|\
> > dcs-930l-b1|\
> > dir-300-b1|\
> > diff --git a/target/linux/ramips/dts/DB-WRT01.dts
> b/target/linux/ramips/dts/DB-WRT01.dts
> > new file mode 100644
> > index 0000000..a8953e9
> > --- /dev/null
> > +++ b/target/linux/ramips/dts/DB-WRT01.dts
> > @@ -0,0 +1,99 @@
> > +/dts-v1/;
> > +
> > +/include/ "mt7620a.dtsi"
> > +
> > +/ {
> > + compatible = "ralink,mt7620a-soc";
> > + model = "Planex DB-WRT01";
> > +
> > + palmbus@10000000 {
> > + gpio1: gpio@638 {
> > + status = "okay";
> > + };
> > +
> > + spi@b00 {
> > + status = "okay";
> > +
> > + m25p80@0 {
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > + compatible = "en25q64";
> > + reg = <0 0>;
> > + linux,modalias = "m25p80", "mx25l6405d";
> > + spi-max-frequency = <10000000>;
> > +
> > + partition@0 {
> > + label = "u-boot";
> > + reg = <0x0 0x30000>;
> > + read-only;
> > + };
> > +
> > + partition@30000 {
> > + label = "u-boot-env";
> > + reg = <0x30000 0x10000>;
> > + read-only;
> > + };
> > +
> > + factory: partition@40000 {
> > + label = "factory";
> > + reg = <0x40000 0x10000>;
> > + read-only;
> > + };
> > +
> > + partition@50000 {
> > + label = "firmware";
> > + reg = <0x50000 0x7b0000>;
> > + };
> > + };
> > + };
> > + };
> > +
> > + pinctrl {
> > + state_default: pinctrl0 {
> > + gpio {
> > + ralink,group = "i2c", "spi refclk",
> "rgmii1";
> > + ralink,function = "gpio";
> > + };
> > + };
> > + };
> > +
> > + ethernet@10100000 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&ephy_pins>;
> > +
>
> Is this empty line really needed here?
>
> > + mtd-mac-address = <&factory 0x4>;
> > + ralink,port-map = "llllw";
> > + };
> > +
> > + gsw@10110000 {
> > + ralink,port4 = "ephy";
> > + };
> > +
> > + wmac@10180000 {
> > + ralink,mtd-eeprom = <&factory 0>;
> > + };
> > +
> > + pcie@10140000 {
> > + status = "okay";
> > + };
> > +
> > + gpio-leds {
> > + compatible = "gpio-leds";
>
> Empty line here, please.
>
> > + power {
> > + label = "db-wrt01:orange:power";
> > + gpios = <&gpio1 1 1>;
> > + };
> > + };
> > +
> > + gpio-keys-polled {
> > + compatible = "gpio-keys-polled";
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > + poll-interval = <20>;
>
> And here too.
>
> > + s1 {
> > + label = "wps";
> > + gpios = <&gpio0 2 1>;
> > + linux,code = <0x211>;
> > + };
> > + };
> > +};
> > diff --git a/target/linux/ramips/image/Makefile
> b/target/linux/ramips/image/Makefile
> > index 2f4d4cb..4632ad2 100644
> > --- a/target/linux/ramips/image/Makefile
> > +++ b/target/linux/ramips/image/Makefile
> > @@ -868,6 +868,7 @@ Image/Build/Profile/CF-WR800N=$(call
> BuildFirmware/Default8M/$(1),$(1),cf-wr800n
> > Image/Build/Profile/DIR-810L=$(call
> BuildFirmware/CustomFlash/$(1),$(1),dir-810l,DIR-810L,$(dlink810l_mtd_size))
> > na930_mtd_size=20971520
> > Image/Build/Profile/NA930=$(call
> BuildFirmware/CustomFlash/$(1),$(1),na930,NA930,$(na930_mtd_size))
> > +Image/Build/Profile/DB-WRT01=$(call
> BuildFirmware/Default8M/$(1),$(1),db-wrt01,DB-WRT01)
> > Image/Build/Profile/MZK-750DHP=$(call
> BuildFirmware/Default8M/$(1),$(1),mzk-750dhp,MZK-750DHP)
> > Image/Build/Profile/OY-0001=$(call
> BuildFirmware/Default16M/$(1),$(1),oy-0001,OY-0001)
> > Image/Build/Profile/Y1=$(call BuildFirmware/Default16M/$(1),$(1),y1,Y1)
> > @@ -901,6 +902,7 @@ define Image/Build/Profile/Default
> > $(call Image/Build/Profile/WHR300HP2,$(1))
> > $(call Image/Build/Profile/WHR600D,$(1))
> > $(call Image/Build/Profile/WHR1166D,$(1))
> > + $(call Image/Build/Profile/DB-WRT01,$(1))
> > $(call Image/Build/Profile/MZK-750DHP,$(1))
> > $(call Image/Build/Profile/NA930,$(1))
> > $(call Image/Build/Profile/OY-0001,$(1))
> > --
> > 1.9.1
> > _______________________________________________
> > openwrt-devel mailing list
> > openwrt-devel@lists.openwrt.org
> > https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
>
_______________________________________________
openwrt-devel mailing list
openwrt-devel@lists.openwrt.org
https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel
