Hi John, Something's wrong with the serial, but I was able to login via Ethernet.
I did not verify PCI yet, as I only have a PCI adapter on the cubes which are in use. Serial log below: bruno On 02/09/2015 12:26 PM, John Crispin wrote: > Hi Bruno, (or anyone else that has the hw at hand) > > i pushed the v3.18 support. could you test it please and let me know if > it is working ? you need to set 3.18 in the Makefile, it is still at 3.14. [ 0.000000] Linux version 3.18.6 (br1@shiva) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r44360) ) #1 Mon Feb 9 20:19:34 WET 2015 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 01030202 (Au1500) [ 0.000000] 4G Systems MTX-1 Board [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000-0x03ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x03ffffff] [ 0.000000] Initmem setup node 0 [mem 0x00000000-0x03ffffff] [ 0.000000] Primary instruction cache 16kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: root=/dev/mtdblock/0 console=ttyS0,115200 root=/dev/mtdblock0 rootfstype=squashfs,jffs2 [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Memory: 60556K/65536K available (2412K kernel code, 95K rwdata, 476K rodata, 144K init, 195K bss, 4980K reserved) [ 0.000000] NR_IRQS:128 [ 0.000000] Alchemy clocksource installed [ 0.004000] Calibrating delay loop... 395.26 BogoMIPS (lpj=790528) [ 0.040000] pid_max: default: 32768 minimum: 301 [ 0.044000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.048000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.056000] NET: Registered protocol family 16 [ 0.060000] Alchemy clocktree installed [ 0.064000] Alchemy DMA initialized [ 0.068000] alchemy-pci alchemy-pci.0: PCI controller at 32 MHz [ 0.100000] PCI host bridge to bus 0000:00 [ 0.104000] pci_bus 0000:00: root bus resource [mem 0x40000000-0x4fffffff] [ 0.108000] pci_bus 0000:00: root bus resource [io 0x1000-0xffff] [ 0.112000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.116000] Switched to clocksource alchemy-counter1 [ 0.124000] NET: Registered protocol family 2 [ 0.128000] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.136000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.144000] TCP: Hash tables configured (established 1024 bind 1024) [ 0.152000] TCP: reno registered [ 0.156000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.160000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.168000] NET: Registered protocol family 1 [ 0.176000] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.188000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.192000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.216000] msgmni has been set to 118 [ 0.224000] io scheduler noop registered [ 0.228000] io scheduler deadline registered (default) [ 0.232000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 0.240000] console [ttyS0] disabled [ 0.244000] serial8250.8: ttyS0 at MMIO 0x11100000 (irq = 8, base_baud = 18187500) is a 16550A ������������������������������������������������������������������������������������������� With 14.07 the last part looks like this: [ 0.180000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 0.192000] serial8250.8: ttyS0 at MMIO 0x11100000 (irq = 8) is a 16550A [ 0.200000] console [ttyS0] enabled, bootconsole disabled [ 0.200000] console [ttyS0] enabled, bootconsole disabled [ 0.216000] serial8250.8: ttyS1 at MMIO 0x11400000 (irq = 11) is a 16550A _______________________________________________ openwrt-devel mailing list openwrt-devel@lists.openwrt.org https://lists.openwrt.org/cgi-bin/mailman/listinfo/openwrt-devel