This requires all the preceding patches and finishes support for the
DGN3500, also removing an obsolete file.
Signed-off-by: Daniel Gimpelevich <dan...@gimpelevich.san-francisco.ca.us>
Index: target/linux/lantiq/base-files/lib/preinit/42_athfix
===================================================================
--- a/target/linux/lantiq/base-files/lib/preinit/42_athfix (revision 36739)
+++ b/target/linux/lantiq/base-files/lib/preinit/42_athfix (working copy)
@@ -1,19 +0,0 @@
-#!/bin/sh
-
-. /lib/functions/lantiq.sh
-
-init_atheeprom() {
- local board=$(lantiq_board_name)
- case $board in
- "Netgear DGN3500B")
- echo "- loading eeprom -"
- dd if=/dev/mtd2 of=/sys/firmware/ath_eeprom bs=1k skip=60
count=4
- echo 0 > /sys/bus/pci/slots/0000\:00\:0e.0/power
- sleep 1
- echo 1 > /sys/bus/pci/rescan
- ;;
- esac
-}
-
-boot_hook_add preinit_essential init_atheeprom
-
Index: target/linux/lantiq/base-files/etc/uci-defaults/02_network
===================================================================
--- a/target/linux/lantiq/base-files/etc/uci-defaults/02_network
(revision 36739)
+++ b/target/linux/lantiq/base-files/etc/uci-defaults/02_network
(working copy)
@@ -72,6 +72,11 @@
VG3503J)
ucidef_set_interface_lan 'eth0 eth1'
;;
+DGN3500*)
+ ucidef_set_interface_lan "eth0.1"
+ ucidef_add_switch "switch0" "1" "1"
+ ucidef_add_switch_vlan "switch0" "1" "3 2 1 0 5t"
+ ;;
esac
[ -z "$(ls /lib/modules/`uname -r`/ltq_atm*)" ] || set_atm_wan "$vpi" "$vci"
"$encaps" "$payload"
Index: target/linux/lantiq/dts/DGN3500.dtsi
===================================================================
--- a/target/linux/lantiq/dts/DGN3500.dtsi (revision 36739)
+++ b/target/linux/lantiq/dts/DGN3500.dtsi (working copy)
@@ -2,7 +2,7 @@
/ {
chosen {
- bootargs = "console=ttyLTQ0,115200 init=/etc/preinit";
+ bootargs-append = "console=ttyLTQ0,115200 init=/etc/preinit";
};
memory@0 {
@@ -112,6 +112,13 @@
};
};
+ ath9k_eep {
+ compatible = "ath9k,eeprom";
+ ath,eep-flash = <2 0xf000>;
+ ath,pci-slot = <14>;
+ ath,eep-swap;
+ };
+
rtl8366rb {
compatible = "rtl8366rb";
gpio-sda = <&gpio 35 0>;
@@ -144,7 +151,7 @@
gpio-leds {
compatible = "gpio-leds";
internet {
- label = "inernet";
+ label = "internet";
gpios = <&gpio 2 1>;
};
dsl {
@@ -158,7 +165,6 @@
power {
label = "power";
gpios = <&gpio 34 1>;
- default-state = "on";
};
power2 {
label = "power2";
_______________________________________________
openwrt-devel mailing list
openwrt-devel@lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel
