This board uses a TrendChip SOC with its own RAM/Flash for ADSL support. We know both SOCs are connected through ethernet and use some kind of protocol for UART communication, but due to the lack of GPL sources we couldn't get it to work. For this reason the network is configured only for LAN.
There are two versions (Chile 8MB and Spain 16MB). Wiki: http://wiki.openwrt.org/toh/alpha/asl26555 Signed-off-by: Esteban Benito <esteban...@gmail.com> Signed-off-by: Álvaro Fernández Rojas <nolt...@gmail.com> --- diff --git a/target/linux/ramips/base-files/etc/diag.sh b/target/linux/ramips/base-files/etc/diag.sh index fe925c0..fdd8b5e 100755 --- a/target/linux/ramips/base-files/etc/diag.sh +++ b/target/linux/ramips/base-files/etc/diag.sh @@ -15,6 +15,9 @@ get_status_led() { argus-atp52b) status_led="argus-atp52b:green:run" ;; + asl26555) + status_led="asl26555:green:power" + ;; br6524n) status_led="edimax:blue:power" ;; diff --git a/target/linux/ramips/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom b/target/linux/ramips/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom index 5915a02..f051459 100644 --- a/target/linux/ramips/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom +++ b/target/linux/ramips/base-files/etc/hotplug.d/firmware/10-rt2x00-eeprom @@ -30,6 +30,7 @@ board=$(ramips_board_name) case "$FIRMWARE" in "soc_wmac.eeprom") case $board in + asl26555 | \ dir-300-b1 | \ dir-600-b1 | \ dir-600-b2 | \ diff --git a/target/linux/ramips/base-files/etc/uci-defaults/01_leds b/target/linux/ramips/base-files/etc/uci-defaults/01_leds index cd17d7f..c330bc7 100755 --- a/target/linux/ramips/base-files/etc/uci-defaults/01_leds +++ b/target/linux/ramips/base-files/etc/uci-defaults/01_leds @@ -35,6 +35,12 @@ case $board in ucidef_set_led_rssi "rssihigh" "RSSIHIGH" "all0256n:green:rssihigh" "wlan0" "70" "100" "-69" "8" set_wifi_led "rt2800pci-phy0::radio" ;; + asl26555) + ucidef_set_led_default "power" "POWER" "asl26555:green:power" "1" + ucidef_set_led_netdev "eth" "ETH" "asl26555:green:eth" "eth0" + set_wifi_led "asl26555:green:wlan" + set_usb_led "asl26555:green:3g" + ;; bc2) set_usb_led "bc2:blue:usb" ;; diff --git a/target/linux/ramips/base-files/etc/uci-defaults/02_network b/target/linux/ramips/base-files/etc/uci-defaults/02_network index e28f2b5..ceb5cbf 100755 --- a/target/linux/ramips/base-files/etc/uci-defaults/02_network +++ b/target/linux/ramips/base-files/etc/uci-defaults/02_network @@ -63,6 +63,12 @@ ramips_setup_interfaces() ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2" ;; + asl26555) + ucidef_set_interface_lan "eth0.1" + ucidef_add_switch "switch0" "1" "1" + ucidef_add_switch_vlan "switch0" "1" "1 2 3 4 6t" + ;; + dir-645) ucidef_set_interfaces_lan_wan "eth0.1" "eth0.2" ucidef_add_switch "switch0" "1" "1" @@ -175,6 +181,10 @@ ramips_setup_macs() wan_mac=$(macaddr_add "$lan_mac" 1) ;; + asl26555) + lan_mac=$(mtd_get_mac_binary devdata 16388) + ;; + w306r-v20) lan_mac=$(mtd_get_mac_binary factory 4) wan_mac=$(macaddr_add "$lan_mac" 5) diff --git a/target/linux/ramips/base-files/lib/preinit/06_set_iface_mac b/target/linux/ramips/base-files/lib/preinit/06_set_iface_mac index 52bf115..aef9f3e 100644 --- a/target/linux/ramips/base-files/lib/preinit/06_set_iface_mac +++ b/target/linux/ramips/base-files/lib/preinit/06_set_iface_mac @@ -33,6 +33,7 @@ preinit_set_mac_address() { mac=$(macaddr_setbit_la "$mac") ifconfig eth0 hw ether $mac 2>/dev/null ;; + asl26555 |\ dir-300-b1 |\ dir-300-b2 |\ dir-600-b1) diff --git a/target/linux/ramips/base-files/lib/ramips.sh b/target/linux/ramips/base-files/lib/ramips.sh index 37b477a..72a7e8c 100755 --- a/target/linux/ramips/base-files/lib/ramips.sh +++ b/target/linux/ramips/base-files/lib/ramips.sh @@ -66,6 +66,9 @@ ramips_board_detect() { *"Asus WL-330N3G") name="wl-330n3g" ;; + *"Alpha ASL26555") + name="asl26555" + ;; *"Aztech HW550-3G") name="hw550-3g" ;; diff --git a/target/linux/ramips/base-files/lib/upgrade/platform.sh b/target/linux/ramips/base-files/lib/upgrade/platform.sh index ef15044..c4bac0d 100755 --- a/target/linux/ramips/base-files/lib/upgrade/platform.sh +++ b/target/linux/ramips/base-files/lib/upgrade/platform.sh @@ -22,6 +22,7 @@ platform_check_image() { all0239-3g | \ all0256n | \ all5002 | \ + asl26555 | \ bc2 | \ broadway | \ carambola | \ diff --git a/target/linux/ramips/dts/ASL26555-16M.dts b/target/linux/ramips/dts/ASL26555-16M.dts new file mode 100644 index 0000000..e9477b4 --- /dev/null +++ b/target/linux/ramips/dts/ASL26555-16M.dts @@ -0,0 +1,138 @@ +/dts-v1/; + +/include/ "rt3050.dtsi" + +/ { + compatible = "ASL26555", "ralink,rt3050-soc"; + model = "Alpha ASL26555"; + + palmbus@10000000 { + sysc@0 { + ralink,pinmux = "spi", "mdio", "uartlite", "sdram", "rgmii"; + ralink,gpiomux = "i2c", "jtag"; + ralink,uartmux = "gpio"; + ralink,wdtmux = <1>; + }; + + gpio0: gpio@600 { + status = "okay"; + }; + + spi@b00 { + status = "okay"; + m25p80@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "s25sl12801"; + reg = <0 0>; + linux,modalias = "m25p80", "s25sl12801"; + spi-max-frequency = <10000000>; + + partition@0 { + label = "uboot"; + reg = <0x0 0x30000>; + read-only; + }; + partition@30000 { + label = "uboot-env"; + reg = <0x30000 0x10000>; + read-only; + }; + partition@40000 { + label = "factory"; + reg = <0x40000 0x10000>; + read-only; + }; + partition@50000 { + label = "firmware"; + reg = <0x50000 0xf80000>; + }; + partition@fd0000 { + label = "cert"; + reg = <0xfd0000 0x10000>; + read-only; + }; + partition@fe0000 { + label = "langpack"; + reg = <0xfe0000 0x10000>; + read-only; + }; + partition@ff0000 { + label = "devdata"; + reg = <0xff0000 0x10000>; + read-only; + }; + }; + }; + }; + + ethernet@10100000 { + status = "okay"; + }; + + esw@10110000 { + status = "okay"; + ralink,portmap = <0x1e>; + }; + + wmac@10180000 { + status = "okay"; + }; + + otg@101c0000 { + status = "okay"; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <20>; + reset { + label = "reset"; + gpios = <&gpio0 10 0>; + linux,code = <0x198>; + }; + wps { + label = "wps"; + gpios = <&gpio0 12 0>; + linux,code = <0x211>; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + eth { + label = "asl26555:green:eth"; + gpios = <&gpio0 0 1>; + }; + wan-red { + label = "asl26555:red:wan"; + gpios = <&gpio0 1 0>; + }; + wan-green { + label = "asl26555:green:wan"; + gpios = <&gpio0 2 0>; + }; + wlan { + label = "asl26555:green:wlan"; + gpios = <&gpio0 7 0>; + }; + power-green { + label = "asl26555:green:power"; + gpios = <&gpio0 8 0>; + }; + power-red { + label = "asl26555:red:power"; + gpios = <&gpio0 9 0>; + }; + 3g-green { + label = "asl26555:green:3g"; + gpios = <&gpio0 14 1>; + }; + 3g-red { + label = "asl26555:red:3g"; + gpios = <&gpio0 17 1>; + }; + }; +}; diff --git a/target/linux/ramips/dts/ASL26555-8M.dts b/target/linux/ramips/dts/ASL26555-8M.dts new file mode 100644 index 0000000..0a403c1 --- /dev/null +++ b/target/linux/ramips/dts/ASL26555-8M.dts @@ -0,0 +1,133 @@ +/dts-v1/; + +/include/ "rt3050.dtsi" + +/ { + compatible = "ASL26555", "ralink,rt3050-soc"; + model = "Alpha ASL26555"; + + palmbus@10000000 { + sysc@0 { + ralink,pinmux = "spi", "mdio", "uartlite", "sdram", "rgmii"; + ralink,gpiomux = "i2c", "jtag"; + ralink,uartmux = "gpio"; + ralink,wdtmux = <1>; + }; + + gpio0: gpio@600 { + status = "okay"; + }; + + spi@b00 { + status = "okay"; + m25p80@0 { + #address-cells = <1>; + #size-cells = <1>; + compatible = "s25sl064p"; + reg = <0 0>; + linux,modalias = "m25p80", "s25sl064p"; + spi-max-frequency = <10000000>; + + partition@0 { + label = "uboot"; + reg = <0x0 0x30000>; + read-only; + }; + partition@30000 { + label = "devdata"; + reg = <0x30000 0x10000>; + read-only; + }; + partition@40000 { + label = "rgdb"; + reg = <0x40000 0x10000>; + read-only; + }; + partition@50000 { + label = "firmware"; + reg = <0x50000 0x790000>; + }; + partition@7e0000 { + label = "cert"; + reg = <0x7e0000 0x10000>; + read-only; + }; + partition@7f0000 { + label = "langpack"; + reg = <0x7f0000 0x10000>; + read-only; + }; + }; + }; + }; + + ethernet@10100000 { + status = "okay"; + }; + + esw@10110000 { + status = "okay"; + ralink,portmap = <0x1e>; + }; + + wmac@10180000 { + status = "okay"; + }; + + otg@101c0000 { + status = "okay"; + }; + + gpio-keys-polled { + compatible = "gpio-keys-polled"; + #address-cells = <1>; + #size-cells = <0>; + poll-interval = <20>; + reset { + label = "reset"; + gpios = <&gpio0 10 0>; + linux,code = <0x198>; + }; + wps { + label = "wps"; + gpios = <&gpio0 12 0>; + linux,code = <0x211>; + }; + }; + + gpio-leds { + compatible = "gpio-leds"; + eth { + label = "asl26555:green:eth"; + gpios = <&gpio0 0 1>; + }; + wan-red { + label = "asl26555:red:wan"; + gpios = <&gpio0 1 0>; + }; + wan-green { + label = "asl26555:green:wan"; + gpios = <&gpio0 2 0>; + }; + wlan { + label = "asl26555:green:wlan"; + gpios = <&gpio0 7 0>; + }; + power-green { + label = "asl26555:green:power"; + gpios = <&gpio0 8 0>; + }; + power-red { + label = "asl26555:red:power"; + gpios = <&gpio0 9 0>; + }; + 3g-green { + label = "asl26555:green:3g"; + gpios = <&gpio0 14 1>; + }; + 3g-red { + label = "asl26555:red:3g"; + gpios = <&gpio0 17 1>; + }; + }; +}; diff --git a/target/linux/ramips/image/Makefile b/target/linux/ramips/image/Makefile index 4e8cde7..b84c8d2 100644 --- a/target/linux/ramips/image/Makefile +++ b/target/linux/ramips/image/Makefile @@ -269,6 +269,18 @@ Image/Build/Profile/ALL5002=$(call BuildFirmware/CustomFlash/$(1),$(1),all5002,A argus_atp52b_mtd_size=7995392 Image/Build/Profile/ARGUS_ATP52B=$(call BuildFirmware/CustomFlash/$(1),$(1),argus_atp52b,ARGUS_ATP52B,$(argus_atp52b_mtd_size)) +asl26555_8mb_mtd_size=7929856 +asl26555_16mb_mtd_size=16252928 +define BuildFirmware/ASL26555/squashfs + $(call BuildFirmware/CustomFlash/$(1),$(1),$(2)-8M,$(3)-8M,$(asl26555_8mb_mtd_size)) + $(call BuildFirmware/CustomFlash/$(1),$(1),$(2)-16M,$(3)-16M,$(asl26555_16mb_mtd_size)) +endef +define BuildFirmware/ASL26555/initramfs + $(call BuildFirmware/OF/initramfs,$(1),$(2)-8M,$(3)-8M) + $(call BuildFirmware/OF/initramfs,$(1),$(2)-16M,$(3)-16M) +endef +Image/Build/Profile/ASL26555=$(call BuildFirmware/ASL26555/$(1),$(1),asl26555,ASL26555) + Image/Build/Profile/BC2=$(call BuildFirmware/Default8M/$(1),$(1),bc2,BC2) broadway_mtd_size=7929856 @@ -424,6 +436,7 @@ define Image/Build/Profile/Default $(call Image/Build/Profile/ALL0256N,$(1)) $(call Image/Build/Profile/ALL5002,$(1)) $(call Image/Build/Profile/ARGUS_ATP52B,$(1)) + $(call Image/Build/Profile/ASL26555,$(1)) $(call Image/Build/Profile/BC2,$(1)) $(call Image/Build/Profile/BROADWAY,$(1)) $(call Image/Build/Profile/CARAMBOLA,$(1)) diff --git a/target/linux/ramips/rt305x/profiles/alpha.mk b/target/linux/ramips/rt305x/profiles/alpha.mk new file mode 100644 index 0000000..a537509 --- /dev/null +++ b/target/linux/ramips/rt305x/profiles/alpha.mk @@ -0,0 +1,19 @@ +# +# Copyright (C) 2013 OpenWrt.org +# +# This is free software, licensed under the GNU General Public License v2. +# See /LICENSE for more information. +# + +define Profile/ASL26555 + NAME:=Alpha ASL26555 + PACKAGES:=\ + kmod-usb-core kmod-usb-rt305x-dwc_otg \ + kmod-ledtrig-usbdev +endef + +define Profile/ASL26555/Description + Package set for Alpha ASL26555 +endef + +$(eval $(call Profile,ASL26555)) _______________________________________________ openwrt-devel mailing list openwrt-devel@lists.openwrt.org https://lists.openwrt.org/mailman/listinfo/openwrt-devel
