Fixed: GPIO typos and confirmed GPIO_BUTTON_RESET
Fixed: Lan & Wan reversed: swaped "eth0.2" with "eth0.1" by removing a
line(default is correct), and reversed the Lan/wan layout LLLLW to WLLLL.
Added: image/Makefile now builds -factory.bin files. I am unsure of the
accepted way to change the makefile but the name of the image needs to be
'linkn Kernel Image' in order to be accepted by the OEM firmware.
Known issue: eth0 (internal switch i think has mac address:00:11:22:33:44:55
but i think it should be same as the lan).
Known issue: Pressing the reset button has no noticable effect, i would expect
the router to boot failsafe if being pressed on boot, reboot if short press and
reset all to default if long press.
Notes:
I understand this unit has two radio units, is there any configuration needed
in the profile?
Gabor,
Thank you for working on and applying my patch, the GPIO was
incorrectly typed 'a9' and should have been '9'. i do not know what checkpatch
is, but if you can direct me i will use it before any future subissions. Apart
from my concerns about this device mentioned above, i also have an intrest in
the cns11xx platform that i beleive you may have worked on once.
Signed-off-by: David Pearce david_18051...@hotmail.com
Index: target/linux/ramips/files/arch/mips/ralink/rt305x/mach-w306r-v20.c
===================================================================
--- target/linux/ramips/files/arch/mips/ralink/rt305x/mach-w306r-v20.c
(revision 31494)
+++ target/linux/ramips/files/arch/mips/ralink/rt305x/mach-w306r-v20.c
(working copy)
@@ -20,7 +20,7 @@
#include "devices.h"
-#define W306R_V20_GPIO_LED_SYS 9 /* FIXME */
+#define W306R_V20_GPIO_LED_SYS 9
#define W306R_V20_GPIO_LED_WPS 13
#define W306R_V20_GPIO_BUTTON_RESET 10
@@ -57,7 +57,7 @@
rt305x_gpio_init(RT305X_GPIO_MODE_GPIO << RT305X_GPIO_MODE_UART0_SHIFT);
- rt305x_esw_data.vlan_config = RT305X_ESW_VLAN_CONFIG_LLLLW;
+ rt305x_esw_data.vlan_config = RT305X_ESW_VLAN_CONFIG_WLLLL;
rt305x_register_ethernet();
ramips_register_gpio_leds(-1, ARRAY_SIZE(w306r_v20_leds_gpio),
w306r_v20_leds_gpio);
Index: target/linux/ramips/image/Makefile
===================================================================
--- target/linux/ramips/image/Makefile (revision 31494)
+++ target/linux/ramips/image/Makefile (working copy)
@@ -220,6 +220,19 @@
$(call BuildFirmware/Generic,$(1),$(2),board=$(3) $(call
mkmtd/phys,$(mtdlayout_rtn10plus)),$(mtd_rtn10plus_kernel_part_size),$(mtd_rtn10plus_rootfs_part_size))
endef
+mtdlayout_W306R=192k(u-boot)ro,64k(u-boot-env)ro,64k(factory)ro,896k(kernel),2880k(rootfs),3776k@0x50000(firmware)
+define BuildFirmware/W306R_4M
+ $(call BuildFirmware/w306r,$(1),$(2),$(call mkcmdline,$(3),$(4),$(5))
$(call mkmtd/$(6),$(mtdlayout_W306R)),917504,2949120)
+endef
+
+define BuildFirmware/w306r
+ $(call PatchKernelLzma,$(2),$(3))
+ mkimage -A mips -O linux -T kernel -C lzma $(call kernel_entry)\
+ -n 'linkn Kernel Image' \
+ -d $(KDIR)/vmlinux-$(2).bin.lzma $(KDIR)/vmlinux-$(2).uImage
+ $(call
CatFiles,$(KDIR)/vmlinux-$(2).uImage,$(4),$(KDIR)/root.$(1),$(5),$(call
imgname,$(1),$(2))-factory.bin)
+endef
+
mtdlayout_whrg300n=192k(u-boot)ro,64k(u-boot-env)ro,64k(factory)ro,960k(kernel),2752k(rootfs),64k(user)ro,3712k@0x50000(firmware)
define BuildFirmware/WHRG300N
$(call
Image/Build/Template/GENERIC_4M,$(1),whr-g300n,WHR-G300N,ttyS1,57600,phys)
@@ -377,6 +390,7 @@
define Image/Build/Profile/W306R_V20
$(call
Image/Build/Template/$(fs_squash)/$(1),GENERIC_4M,w306r-v20,W306R_V20,ttyS1,57600,phys)
+ $(call
Image/Build/Template/$(fs_squash)/$(1),W306R_4M,w306r-v20,W306R_V20,ttyS1,57600,phys)
endef
define Image/Build/Profile/W502U
Index: target/linux/ramips/base-files/etc/uci-defaults/network
===================================================================
--- target/linux/ramips/base-files/etc/uci-defaults/network (revision 31494)
+++ target/linux/ramips/base-files/etc/uci-defaults/network (working copy)
@@ -59,7 +59,6 @@
;;
freestation5 | \
- w306r-v20 | \
wcr-150gn)
ucidef_set_interfaces_lan_wan "eth0.2" "eth0.1"
;;
Index: target/linux/ramips/base-files/etc/diag.sh
===================================================================
--- target/linux/ramips/base-files/etc/diag.sh (revision 31494)
+++ target/linux/ramips/base-files/etc/diag.sh (working copy)
@@ -82,7 +82,7 @@
status_led="v22rw-2x2:green:security"
;;
w306r-v20)
- status_led="w306r:green:sys"
+ status_led="w306r-v20:green:sys"
;;
w502u)
status_led="alfa:blue:wps"
_______________________________________________
openwrt-devel mailing list
openwrt-devel@lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel
