kirkwood: introduce files folder in order to simplify patches
Signed-off-by: Luka Perkov <open...@lukaperkov.net>
---
diff --git
a/target/linux/kirkwood/files/arch/arm/mach-kirkwood/iconnect-setup.c
b/target/linux/kirkwood/files/arch/arm/mach-kirkwood/iconnect-setup.c
new file mode 100644
index 0000000..1915caa
--- /dev/null
+++ b/target/linux/kirkwood/files/arch/arm/mach-kirkwood/iconnect-setup.c
@@ -0,0 +1,188 @@
+/*
+ * arch/arm/mach-kirkwood/iconnect-setup.c
+ *
+ * Iomega iConnect Wireless
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/platform_device.h>
+#include <linux/irq.h>
+#include <linux/mtd/partitions.h>
+#include <linux/mv643xx_eth.h>
+#include <linux/ethtool.h>
+#include <linux/gpio.h>
+#include <linux/gpio_keys.h>
+#include <linux/input.h>
+#include <linux/leds.h>
+#include <asm/mach-types.h>
+#include <asm/mach/arch.h>
+#include <mach/kirkwood.h>
+#include "common.h"
+#include "mpp.h"
+
+static struct mtd_partition iconnect_nand_parts[] = {
+ {
+ .name = "u-boot",
+ .offset = 0,
+ .size = SZ_1M
+ }, {
+ .name = "uImage",
+ .offset = MTDPART_OFS_NXTBLK,
+ .size = SZ_1M + SZ_2M
+ }, {
+ .name = "rootfs",
+ .offset = MTDPART_OFS_NXTBLK,
+ .size = SZ_32M,
+ }, {
+ .name = "data",
+ .offset = MTDPART_OFS_NXTBLK,
+ .size = MTDPART_SIZ_FULL
+ },
+};
+
+static struct mv643xx_eth_platform_data iconnect_ge00_data = {
+ .phy_addr = MV643XX_ETH_PHY_ADDR(11),
+};
+
+static struct gpio_led iconnect_led_pins[] = {
+ {
+ .name = "iconnect:blue:power",
+ .default_trigger = "default-on",
+ .gpio = 42,
+ },
+ {
+ .name = "iconnect:red:power",
+ .gpio = 43,
+ },
+ {
+ .name = "iconnect:blue:usb1",
+ .gpio = 44,
+ },
+ {
+ .name = "iconnect:blue:usb2",
+ .gpio = 45,
+ },
+ {
+ .name = "iconnect:blue:usb3",
+ .gpio = 46,
+ },
+ {
+ .name = "iconnect:blue:usb4",
+ .gpio = 47,
+ },
+ {
+ .name = "iconnect:blue:otb",
+ .gpio = 48,
+ },
+};
+
+static struct gpio_led_platform_data iconnect_led_data = {
+ .leds = iconnect_led_pins,
+ .num_leds = ARRAY_SIZE(iconnect_led_pins),
+};
+
+static struct platform_device iconnect_leds = {
+ .name = "leds-gpio",
+ .id = -1,
+ .dev = {
+ .platform_data = &iconnect_led_data,
+ }
+};
+
+#define ICONNECT_GPIO_KEY_RESET 12
+#define ICONNECT_GPIO_KEY_OTB 35
+
+#define ICONNECT_SW_RESET 0x00
+#define ICONNECT_SW_OTB 0x01
+
+static struct gpio_keys_button iconnect_buttons[] = {
+ {
+ .type = EV_SW,
+ .code = ICONNECT_SW_RESET,
+ .gpio = ICONNECT_GPIO_KEY_RESET,
+ .desc = "Reset Button",
+ .active_low = 1,
+ .debounce_interval = 100,
+ },
+ {
+ .type = EV_SW,
+ .code = ICONNECT_SW_OTB,
+ .gpio = ICONNECT_GPIO_KEY_OTB,
+ .desc = "OTB Button",
+ .active_low = 1,
+ .debounce_interval = 100,
+ },
+};
+
+static struct gpio_keys_platform_data iconnect_button_data = {
+ .buttons = iconnect_buttons,
+ .nbuttons = ARRAY_SIZE(iconnect_buttons),
+};
+
+static struct platform_device iconnect_button_device = {
+ .name = "gpio-keys",
+ .id = -1,
+ .num_resources = 0,
+ .dev = {
+ .platform_data = &iconnect_button_data,
+ },
+};
+
+static unsigned int iconnect_mpp_config[] __initdata = {
+ MPP12_GPIO, /*Input for reset button*/
+ MPP35_GPIO, /*Input for OTB button*/
+ MPP42_GPIO,
+ MPP43_GPIO,
+ MPP44_GPIO,
+ MPP45_GPIO,
+ MPP46_GPIO,
+ MPP47_GPIO,
+ MPP48_GPIO,
+ 0
+};
+
+static void __init iconnect_init(void)
+{
+ u32 dev, rev;
+
+ /*
+ * Basic setup. Needs to be called early.
+ */
+ kirkwood_init();
+ kirkwood_mpp_conf(iconnect_mpp_config);
+
+ kirkwood_nand_init(ARRAY_AND_SIZE(iconnect_nand_parts), 25);
+ kirkwood_ehci_init();
+
+ kirkwood_ge00_init(&iconnect_ge00_data);
+ kirkwood_pcie_id(&dev, &rev);
+
+ kirkwood_uart0_init();
+ kirkwood_i2c_init();
+
+ platform_device_register(&iconnect_leds);
+ platform_device_register(&iconnect_button_device);
+}
+
+static int __init iconnect_pci_init(void)
+{
+ if (machine_is_iconnect())
+ kirkwood_pcie_init(KW_PCIE0);
+
+ return 0;
+}
+subsys_initcall(iconnect_pci_init);
+
+
+MACHINE_START(ICONNECT, "Iomega iConnect Wireless")
+ .atag_offset = 0x100,
+ .init_machine = iconnect_init,
+ .map_io = kirkwood_map_io,
+ .init_irq = kirkwood_init_irq,
+ .timer = &kirkwood_timer,
+MACHINE_END
diff --git a/target/linux/kirkwood/patches/002-mvsdio_delay.patch
b/target/linux/kirkwood/patches/002-mvsdio_delay.patch
index ba28853..d9cda32 100644
--- a/target/linux/kirkwood/patches/002-mvsdio_delay.patch
+++ b/target/linux/kirkwood/patches/002-mvsdio_delay.patch
@@ -1,6 +1,6 @@
--- a/drivers/mmc/core/sd.c
+++ b/drivers/mmc/core/sd.c
-@@ -332,6 +332,15 @@ int mmc_sd_switch_hs(struct mmc_card *ca
+@@ -389,6 +389,15 @@ int mmc_sd_switch_hs(struct mmc_card *ca
return -ENOMEM;
}
@@ -18,7 +18,7 @@
goto out;
--- a/drivers/mmc/core/core.c
+++ b/drivers/mmc/core/core.c
-@@ -303,9 +303,9 @@ void mmc_set_data_timeout(struct mmc_dat
+@@ -517,9 +517,9 @@ void mmc_set_data_timeout(struct mmc_dat
* The limit is really 250 ms, but that is
* insufficient for some crappy cards.
*/
diff --git a/target/linux/kirkwood/patches/100-boards.patch
b/target/linux/kirkwood/patches/100-boards.patch
new file mode 100644
index 0000000..0636da7
--- /dev/null
+++ b/target/linux/kirkwood/patches/100-boards.patch
@@ -0,0 +1,34 @@
+--- a/arch/arm/mach-kirkwood/Makefile
++++ b/arch/arm/mach-kirkwood/Makefile
+@@ -18,5 +18,6 @@ obj-$(CONFIG_MACH_D2NET_V2) += d2net_v2
+ obj-$(CONFIG_MACH_NET2BIG_V2) += netxbig_v2-setup.o lacie_v2-common.o
+ obj-$(CONFIG_MACH_NET5BIG_V2) += netxbig_v2-setup.o lacie_v2-common.o
+ obj-$(CONFIG_MACH_T5325) += t5325-setup.o
++obj-$(CONFIG_MACH_ICONNECT) += iconnect-setup.o
+
+ obj-$(CONFIG_CPU_IDLE) += cpuidle.o
+--- a/arch/arm/mach-kirkwood/Kconfig
++++ b/arch/arm/mach-kirkwood/Kconfig
+@@ -130,6 +130,12 @@ config MACH_T5325
+ Say 'Y' here if you want your kernel to support the
+ HP t5325 Thin Client.
+
++config MACH_ICONNECT
++ bool "Iomega iConnect Wireless"
++ help
++ Say 'Y' here if you want your kernel to support the
++ Iomega iConnect Wireless.
++
+ endmenu
+
+ endif
+--- a/arch/arm/mach-kirkwood/mpp.h
++++ b/arch/arm/mach-kirkwood/mpp.h
+@@ -102,6 +102,7 @@
+ #define MPP11_SATA0_ACTn MPP( 11, 0x5, 0, 1, 0, 1, 1, 1, 1 )
+
+ #define MPP12_GPO MPP( 12, 0x0, 0, 1, 1, 1, 1, 1, 1 )
++#define MPP12_GPIO MPP( 12, 0x0, 1, 1, 1, 1, 1, 1, 1 )
+ #define MPP12_SD_CLK MPP( 12, 0x1, 0, 1, 1, 1, 1, 1, 1 )
+ #define MPP12_AU_SPDIF0 MPP( 12, 0xa, 0, 1, 0, 0, 0, 0,
1 )
+ #define MPP12_SPI_MOSI MPP( 12, 0xb, 0, 1, 0, 0, 0, 0,
1 )
diff --git a/target/linux/kirkwood/patches/200-iconnect.patch
b/target/linux/kirkwood/patches/200-iconnect.patch
deleted file mode 100644
index 30693a8..0000000
--- a/target/linux/kirkwood/patches/200-iconnect.patch
+++ /dev/null
@@ -1,226 +0,0 @@
---- a/arch/arm/mach-kirkwood/Makefile
-+++ b/arch/arm/mach-kirkwood/Makefile
-@@ -8,6 +8,7 @@ obj-$(CONFIG_MACH_SHEEVAPLUG) += sheeva
- obj-$(CONFIG_MACH_ESATA_SHEEVAPLUG) += sheevaplug-setup.o
- obj-$(CONFIG_MACH_GURUPLUG) += guruplug-setup.o
- obj-$(CONFIG_MACH_DOCKSTAR) += dockstar-setup.o
-+obj-$(CONFIG_MACH_ICONNECT) += iconnect-setup.o
- obj-$(CONFIG_MACH_TS219) += ts219-setup.o tsx1x-common.o
- obj-$(CONFIG_MACH_TS41X) += ts41x-setup.o tsx1x-common.o
- obj-$(CONFIG_MACH_OPENRD) += openrd-setup.o
---- a/arch/arm/mach-kirkwood/Kconfig
-+++ b/arch/arm/mach-kirkwood/Kconfig
-@@ -130,6 +130,12 @@ config MACH_T5325
- Say 'Y' here if you want your kernel to support the
- HP t5325 Thin Client.
-
-+config MACH_ICONNECT
-+ bool "Iomega iConnect Wireless"
-+ help
-+ Say 'Y' here if you want your kernel to support the
-+ Iomega iConnect Wireless.
-+
- endmenu
-
- endif
---- a/arch/arm/mach-kirkwood/mpp.h
-+++ b/arch/arm/mach-kirkwood/mpp.h
-@@ -108,6 +108,7 @@
- #define MPP11_SATA0_ACTn MPP( 11, 0x5, 0, 1, 0, 1, 1, 1, 1 )
-
- #define MPP12_GPO MPP( 12, 0x0, 0, 1, 1, 1, 1, 1, 1 )
-+#define MPP12_GPIO MPP( 12, 0x0, 1, 1, 1, 1, 1, 1, 1 )
- #define MPP12_SD_CLK MPP( 12, 0x1, 0, 1, 1, 1, 1, 1, 1 )
- #define MPP12_AU_SPDIF0 MPP( 12, 0xa, 0, 1, 0, 0, 0, 0,
1 )
- #define MPP12_SPI_MOSI MPP( 12, 0xb, 0, 1, 0, 0, 0, 0,
1 )
---- /dev/null
-+++ b/arch/arm/mach-kirkwood/iconnect-setup.c
-@@ -0,0 +1,188 @@
-+/*
-+ * arch/arm/mach-kirkwood/iconnect-setup.c
-+ *
-+ * Iomega iConnect Wireless
-+ *
-+ * This file is licensed under the terms of the GNU General Public
-+ * License version 2. This program is licensed "as is" without any
-+ * warranty of any kind, whether express or implied.
-+ */
-+
-+#include <linux/kernel.h>
-+#include <linux/init.h>
-+#include <linux/platform_device.h>
-+#include <linux/irq.h>
-+#include <linux/mtd/partitions.h>
-+#include <linux/mv643xx_eth.h>
-+#include <linux/ethtool.h>
-+#include <linux/gpio.h>
-+#include <linux/gpio_keys.h>
-+#include <linux/input.h>
-+#include <linux/leds.h>
-+#include <asm/mach-types.h>
-+#include <asm/mach/arch.h>
-+#include <mach/kirkwood.h>
-+#include "common.h"
-+#include "mpp.h"
-+
-+static struct mtd_partition iconnect_nand_parts[] = {
-+ {
-+ .name = "u-boot",
-+ .offset = 0,
-+ .size = SZ_1M
-+ }, {
-+ .name = "uImage",
-+ .offset = MTDPART_OFS_NXTBLK,
-+ .size = SZ_1M + SZ_2M
-+ }, {
-+ .name = "rootfs",
-+ .offset = MTDPART_OFS_NXTBLK,
-+ .size = SZ_32M,
-+ }, {
-+ .name = "data",
-+ .offset = MTDPART_OFS_NXTBLK,
-+ .size = MTDPART_SIZ_FULL
-+ },
-+};
-+
-+static struct mv643xx_eth_platform_data iconnect_ge00_data = {
-+ .phy_addr = MV643XX_ETH_PHY_ADDR(11),
-+};
-+
-+static struct gpio_led iconnect_led_pins[] = {
-+ {
-+ .name = "iconnect:blue:power",
-+ .default_trigger = "default-on",
-+ .gpio = 42,
-+ },
-+ {
-+ .name = "iconnect:red:power",
-+ .gpio = 43,
-+ },
-+ {
-+ .name = "iconnect:blue:usb1",
-+ .gpio = 44,
-+ },
-+ {
-+ .name = "iconnect:blue:usb2",
-+ .gpio = 45,
-+ },
-+ {
-+ .name = "iconnect:blue:usb3",
-+ .gpio = 46,
-+ },
-+ {
-+ .name = "iconnect:blue:usb4",
-+ .gpio = 47,
-+ },
-+ {
-+ .name = "iconnect:blue:otb",
-+ .gpio = 48,
-+ },
-+};
-+
-+static struct gpio_led_platform_data iconnect_led_data = {
-+ .leds = iconnect_led_pins,
-+ .num_leds = ARRAY_SIZE(iconnect_led_pins),
-+};
-+
-+static struct platform_device iconnect_leds = {
-+ .name = "leds-gpio",
-+ .id = -1,
-+ .dev = {
-+ .platform_data = &iconnect_led_data,
-+ }
-+};
-+
-+#define ICONNECT_GPIO_KEY_RESET 12
-+#define ICONNECT_GPIO_KEY_OTB 35
-+
-+#define ICONNECT_SW_RESET 0x00
-+#define ICONNECT_SW_OTB 0x01
-+
-+static struct gpio_keys_button iconnect_buttons[] = {
-+ {
-+ .type = EV_SW,
-+ .code = ICONNECT_SW_RESET,
-+ .gpio = ICONNECT_GPIO_KEY_RESET,
-+ .desc = "Reset Button",
-+ .active_low = 1,
-+ .debounce_interval = 100,
-+ },
-+ {
-+ .type = EV_SW,
-+ .code = ICONNECT_SW_OTB,
-+ .gpio = ICONNECT_GPIO_KEY_OTB,
-+ .desc = "OTB Button",
-+ .active_low = 1,
-+ .debounce_interval = 100,
-+ },
-+};
-+
-+static struct gpio_keys_platform_data iconnect_button_data = {
-+ .buttons = iconnect_buttons,
-+ .nbuttons = ARRAY_SIZE(iconnect_buttons),
-+};
-+
-+static struct platform_device iconnect_button_device = {
-+ .name = "gpio-keys",
-+ .id = -1,
-+ .num_resources = 0,
-+ .dev = {
-+ .platform_data = &iconnect_button_data,
-+ },
-+};
-+
-+static unsigned int iconnect_mpp_config[] __initdata = {
-+ MPP12_GPIO, /*Input for reset button*/
-+ MPP35_GPIO, /*Input for OTB button*/
-+ MPP42_GPIO,
-+ MPP43_GPIO,
-+ MPP44_GPIO,
-+ MPP45_GPIO,
-+ MPP46_GPIO,
-+ MPP47_GPIO,
-+ MPP48_GPIO,
-+ 0
-+};
-+
-+static void __init iconnect_init(void)
-+{
-+ u32 dev, rev;
-+
-+ /*
-+ * Basic setup. Needs to be called early.
-+ */
-+ kirkwood_init();
-+ kirkwood_mpp_conf(iconnect_mpp_config);
-+
-+ kirkwood_nand_init(ARRAY_AND_SIZE(iconnect_nand_parts), 25);
-+ kirkwood_ehci_init();
-+
-+ kirkwood_ge00_init(&iconnect_ge00_data);
-+ kirkwood_pcie_id(&dev, &rev);
-+
-+ kirkwood_uart0_init();
-+ kirkwood_i2c_init();
-+
-+ platform_device_register(&iconnect_leds);
-+ platform_device_register(&iconnect_button_device);
-+}
-+
-+static int __init iconnect_pci_init(void)
-+{
-+ if (machine_is_iconnect())
-+ kirkwood_pcie_init(KW_PCIE0);
-+
-+ return 0;
-+}
-+subsys_initcall(iconnect_pci_init);
-+
-+
-+MACHINE_START(ICONNECT, "Iomega iConnect Wireless")
-+ .atag_offset = 0x100,
-+ .init_machine = iconnect_init,
-+ .map_io = kirkwood_map_io,
-+ .init_irq = kirkwood_init_irq,
-+ .timer = &kirkwood_timer,
-+MACHINE_END
_______________________________________________
openwrt-devel mailing list
openwrt-devel@lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel
