On Tue, 21 Feb 2012 09:41:44 +0100, John Crispin wrote:
On 21/02/12 09:17, lee.es...@nowonline.co.uk wrote:
Hi,

I've been running the Buffalo WBMR-HP-G300H routers for a while now,
actually three of them on a bonded line, and in general they are working
very well.

On one of the lines I am seeing very frequent reboots (of the whole
system, not just the DSL) every two or three hours, the other two lines seem to be stable (although I have seen reboots on the other lines, not
for the last week or so). The "faulty" line is the one that seems to
sync closer to it's limit (it has a smaller noise margin) but it's been
stable with other DSL routers in the past.

I am going to swap the hardware around, to make sure it's not something hardware related (they are all running the same firmware), although I
suspect it's a panic caused by the lantiq driver when some situation
happens on the line ... the same router stayed up for over 6 weeks with
no DSL connected while I was puting the build together.

Is there any way to get a crash dump configured in openwrt so I can get
more info about the reboot cause?


crashlog is what you are looking for.....


../o.git/build_dir/linux-lantiq_ar9/linux-3.1.9/patches/generic/930-crashlog.patch


Thanks John ... it was already configured and I had a reboot this morning, interestingly though it doesn't actually look like the lantiq driver ... the first backtrace I get once after boot, doesn't seem to be a problem, the second one is the Oops! So is the problem the "eth0: tx ring full"??

<4>[ 20.004000] Infineon CPE API Driver version: DSL CPE API V3.24.4.4
<6>[   20.144000]     ATM (A1) firmware version 1.0.19
<4>[   20.148000] ifxmips_atm: ATM init succeed
<6>[   20.180000] dwc_otg: version 2.60a 22-NOV-2006
<6>[   20.784000] DWC_otg: Using DMA mode
<6>[   20.784000] dwc_otg dwc_otg.0: DWC OTG Controller
<6>[ 20.788000] dwc_otg dwc_otg.0: new USB bus registered, assigned bus number 1
<6>[   20.796000] dwc_otg dwc_otg.0: irq 62, io mem 0xffffffffbe101000
<6>[   20.804000] DWC_otg: Init: Port Power? op_state=1
<6>[   20.808000] DWC_otg: Init: Power Port (0)
<6>[   20.812000] hub 1-0:1.0: USB hub found
<6>[   20.816000] hub 1-0:1.0: 1 port detected
<6>[ 20.844000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled/input/input0
<4>[   20.968000] DISCONNECTED PORT
<6>[   22.924000] device eth0 entered promiscuous mode
<6>[   22.976000] br-lan: port 1(eth0) entering forwarding state
<6>[   22.980000] br-lan: port 1(eth0) entering forwarding state
<6>[   27.588000] device eth0 left promiscuous mode
<6>[   27.592000] br-lan: port 1(eth0) entering forwarding state
<6>[   27.976000] device eth0 entered promiscuous mode
<6>[   27.980000] br-lan: port 1(eth0) entering forwarding state
<6>[   27.984000] br-lan: port 1(eth0) entering forwarding state
<3>[ 55.300000] [DSL_BSP_Showtime 916]: Datarate US intl = 448000, fast = 0
<4>[   58.044000] ------------[ cut here ]------------
<4>[   58.044000] WARNING: at kernel/softirq.c:159 0x80022258()
<4>[ 58.044000] Modules linked in: gpio_keys_polled dwc_otg lantiq_atm drv_dsl_cpe_api lantiq_mei ledtrig_usbdev ip6t_REJECT ip6t_LOG ip6t_rt ip6t_hbh ip6t_mh ip6t_ipv6header ip6t_frag ip6t_eui64 ip6t_ah ip6table_raw ip6_queue ip6table_mangle ip6table_filter ip6_tables nf_conntrack_ipv6 nf_defrag_ipv6 nf_nat_irc nf_conntrack_irc nf_nat_ftp nf_conntrack_ftp ipt_MASQUERADE iptable_nat nf_nat xt_conntrack xt_CT xt_NOTRACK iptable_raw xt_state nf_conntrack_ipv4 nf_defrag_ipv4 nf_conntrack pppoe pppox pppoatm ipt_REJECT xt_TCPMSS ipt_LOG xt_comment xt_multiport xt_mac xt_limit iptable_mangle iptable_filter ip_tables xt_tcpudp x_tables ppp_async ppp_generic slhc button_hotplug br2684 atm ath9k ath9k_common ath9k_hw ath mac80211 usbcore nls_base crc_ccitt ipv6 cfg80211 compat arc4 aes_generic crypto_algapi
<4>[   58.044000] Call Trace:[<8022c144>] 0x8022c144
<4>[   58.044000] [<8022c144>] 0x8022c144
<4>[   58.044000] [<8001b96c>] 0x8001b96c
<4>[   58.044000] [<80022258>] 0x80022258
<4>[   58.044000] [<8001b9b0>] 0x8001b9b0
<4>[   58.044000] [<801943f4>] 0x801943f4
<4>[   58.044000] [<831c437c>] 0x831c437c
<4>[   58.044000] [<80022258>] 0x80022258
<4>[   58.044000] [<832e4640>] 0x832e4640
<4>[   58.044000] [<80015c58>] 0x80015c58
<4>[   58.044000] [<83281330>] 0x83281330
<4>[   58.044000] [<8004f370>] 0x8004f370
<4>[   58.044000] [<800309b8>] 0x800309b8
<4>[   58.044000] [<8004f5b0>] 0x8004f5b0
<4>[   58.044000] [<80051784>] 0x80051784
<4>[   58.044000] [<8004ecf8>] 0x8004ecf8
<4>[   58.044000] [<800079b4>] 0x800079b4
<4>[   58.044000] [<800031c8>] 0x800031c8
<4>[   58.044000] [<80022130>] 0x80022130
<4>[   58.044000] [<80005ecc>] 0x80005ecc
<4>[   58.044000] [<800060a0>] 0x800060a0
<4>[   58.044000] [<8001701c>] 0x8001701c
<4>[   58.044000] [<80007a10>] 0x80007a10
<4>[   58.044000] [<800060c0>] 0x800060c0
<4>[   58.044000] [<8028e8ec>] 0x8028e8ec
<4>[   58.044000] [<8028e230>] 0x8028e230
<4>[   58.044000]
<4>[   58.044000] ---[ end trace 01fcc832fe4215f4 ]---
<3>[ 6986.092000] eth0: tx ring full
<1>[ 6986.096000] CPU 0 Unable to handle kernel paging request at virtual address 00000060, epc == 8019e960, ra == 801a08d8
<4>[ 6986.104000] Oops[#1]:
<4>[ 6986.104000] Cpu 0
<4>[ 6986.104000] $ 0   : 00000000 00000001 00000000 00000000
<4>[ 6986.104000] $ 4   : 83328b00 83835000 00008100 83964280
<4>[ 6986.104000] $ 8   : 8335a000 832fa000 82ce8000 83bf7000
<4>[ 6986.104000] $12   : 82ce0000 00000000 6e000000 8335e000
<4>[ 6986.104000] $16   : 8328b280 83328b00 83835000 00000000
<4>[ 6986.104000] $20   : 80278aa4 83964280 8023e5a0 8027c508
<4>[ 6986.104000] $24   : 00000000 8328134c
<4>[ 6986.104000] $28   : 80276000 80277cd8 8027cae0 801a08d8
<4>[ 6986.104000] Hi    : 00000000
<4>[ 6986.104000] Lo    : 00000000
<4>[ 6986.104000] epc   : 8019e960 0x8019e960
<4>[ 6986.104000]     Tainted: G        W
<4>[ 6986.104000] ra    : 801a08d8 0x801a08d8
<4>[ 6986.104000] Status: 1100fc03    KERNEL EXL IE
<4>[ 6986.104000] Cause : 80800008
<4>[ 6986.104000] BadVA : 00000060
<4>[ 6986.104000] PrId  : 0001954c (MIPS 34Kc)
<4>[ 6986.104000] Modules linked in: gpio_keys_polled dwc_otg lantiq_atm drv_dsl_cpe_api lantiq_mei ledtrig_usbdev ip6t_REJECT ip6t_LOG ip6t_rt ip6t_hbh ip6t_mh ip6t_ipv6header ip6t_frag ip6t_eui64 ip6t_ah ip6table_raw ip6_queue ip6table_mangle ip6table_filter ip6_tables nf_conntrack_ipv6 nf_defrag_ipv6 nf_nat_irc nf_conntrack_irc nf_nat_ftp nf_conntrack_ftp ipt_MASQUERADE iptable_nat nf_nat xt_conntrack xt_CT xt_NOTRACK iptable_raw xt_state nf_conntrack_ipv4 nf_defrag_ipv4 nf_conntrack pppoe pppox pppoatm ipt_REJECT xt_TCPMSS ipt_LOG xt_comment xt_multiport xt_mac xt_limit iptable_mangle iptable_filter ip_tables xt_tcpudp x_tables ppp_async ppp_generic slhc button_hotplug br2684 atm ath9k ath9k_common ath9k_hw ath mac80211 usbcore nls_base crc_ccitt ipv6 cfg80211 compat arc4 aes_generic crypto_algapi <4>[ 6986.104000] Process swapper (pid: 0, threadinfo=80276000, task=80279c20, tls=00000000) <4>[ 6986.104000] Stack : 0000000b 8380813c 83801420 80086640 0000003c 801943f4 00000020 c0000000 <4>[ 6986.104000] 8328b280 83835000 83964280 83328b00 00000010 00000001 802c0000 8027c508 <4>[ 6986.104000] 8027cae0 801b50f4 82cd4478 802c9ba0 8028d840 83281330 83328b00 8328b280 <4>[ 6986.104000] 00000040 802d0000 8025ac44 801b5434 8028d840 801938a4 00000020 802c31e0 <4>[ 6986.104000] 8328b2dc 00000000 8028d840 00000000 80280000 00010000 fffffffe 80259c94
<4>[ 6986.104000]         ...
<4>[ 6986.104000] Call Trace:[<80086640>] 0x80086640
<4>[ 6986.104000] [<801943f4>] 0x801943f4
<4>[ 6986.104000] [<801b50f4>] 0x801b50f4
<4>[ 6986.104000] [<83281330>] 0x83281330
<4>[ 6986.104000] [<801b5434>] 0x801b5434
<4>[ 6986.104000] [<801938a4>] 0x801938a4
<4>[ 6986.104000] [<8019bd74>] 0x8019bd74
<4>[ 6986.104000] [<80021f30>] 0x80021f30
<4>[ 6986.104000] [<80051784>] 0x80051784
<4>[ 6986.104000] [<80022130>] 0x80022130
<4>[ 6986.104000] [<800031c8>] 0x800031c8
<4>[ 6986.104000] [<80022130>] 0x80022130
<4>[ 6986.104000] [<80005ecc>] 0x80005ecc
<4>[ 6986.104000] [<8001701c>] 0x8001701c
<4>[ 6986.104000] [<800060a0>] 0x800060a0
<4>[ 6986.104000] [<8001701c>] 0x8001701c
<4>[ 6986.104000] [<80007a10>] 0x80007a10
<4>[ 6986.104000] [<800060c0>] 0x800060c0
<4>[ 6986.104000] [<8028e8ec>] 0x8028e8ec
<4>[ 6986.104000] [<8028e230>] 0x8028e230
<4>[ 6986.104000]
<4>[ 6986.104000]
<4>[ 6986.104000] Code: 8c830014  94820062  34068100
<4>[ 6986.104000]  8c650060  8c8200a0  8c63006c  94420010  34630080
<4>[ 6986.388000] ---[ end trace 01fcc832fe4215f5 ]---




_______________________________________________
openwrt-devel mailing list
openwrt-devel@lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel

Reply via email to