Hi! Usb ports on my Asus WL500gPv2 do not work with the latest trunk. I tried to build a fresh checkout. Full log is attached. Here is what I think is the problem:
usb 1-1: device descriptor read/64, error -62 usb 1-1: device descriptor read/64, error -62 usb 1-1: new full speed USB device number 3 using ohci_hcd usb 1-1: device descriptor read/64, error -62 usb 1-1: device descriptor read/64, error -62 usb 1-1: new full speed USB device number 4 using ohci_hcd usb 1-1: device not accepting address 4, error -62 usb 1-1: new full speed USB device number 5 using ohci_hcd usb 1-1: device not accepting address 5, error -62 hub 1-0:1.0: unable to enumerate USB device on port 1 What can I do to fix this? -- Alexander
Linux version 3.0.3 (alex@desktopvm) (gcc version 4.5.4 20110808 (prerelease) (Linaro GCC 4.5-2011.08) ) #1 Wed Aug 31 15:08:13 MSK 2011
CPU revision is: 00029029 (Broadcom BMIPS3300)
bcm47xx: using ssb bus
ssb: chipcommon status is 0x0
ssb: Initializing MIPS core...
ssb: set_irq: core 0x0806, irq 4 => 4
ssb: set_irq: core 0x0816, irq 5 => 2
ssb: set_irq: core 0x0812, irq 2 => 5
ssb: after irq reconfiguration
ssb: core 0x0800, irq : 2(S) 3* 4 5 6 D I
ssb: core 0x0806, irq : 2(S) 3 4* 5 6 D I
ssb: core 0x0816, irq : 2(S)* 3 4 5 6 D I
ssb: core 0x0819, irq : 2(S) 3 4 5 6* D I
ssb: core 0x080f, irq : 2(S) 3 4 5 6 D I*
ssb: core 0x0812, irq : 2(S) 3 4 5* 6 D I
ssb: core 0x081c, irq : 2(S) 3 4 5 6 D I*
found parallel flash.
ssb: Sonics Silicon Backplane found at address 0x18000000
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
Normal 0x00000000 -> 0x00002000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00002000
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
PID hash table entries: 128 (order: -3, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Primary instruction cache 16kB, VIPT, 4-way, linesize 16 bytes.
Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
Memory: 29400k/32768k available (2260k kernel code, 3368k reserved, 481k data, 156k init, 0k highmem)
NR_IRQS:128
console [ttyS0] enabled
Calibrating delay loop... 239.10 BogoMIPS (lpj=478208)
pid_max: default: 32768 minimum: 301
Mount-cache hash table entries: 512
NET: Registered protocol family 16
bio: create slab <bio-0> at 0
Switching to clocksource MIPS
Switched to NOHz mode on CPU #0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
UDP hash table entries: 256 (order: 0, 4096 bytes)
UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
msgmni has been set to 57
io scheduler noop registered
io scheduler deadline registered (default)
Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
serial8250: ttyS0 at MMIO 0xb8000300 (irq = 3) is a U6_16550A
serial8250: ttyS1 at MMIO 0xb8000400 (irq = 3) is a U6_16550A
�erial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 3) is a U6_16550A
serial8250.0: ttyS1 at MMIO 0xb8000400 (irq = 3) is a U6_16550A
bcm47xx_pflash: flash init: 0x1c000000 0x02000000
Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x0022cb
Amd/Fujitsu Extended Query Table at 0x0040
Amd/Fujitsu Extended Query version 1.1.
number of CFI chips: 1
bcm47xx_pflash: Flash device: 0x2000000 at 0x1fc00000
bcm47xx_part: bootloader size: 131072
bcm47xx_part: Looking for dual image
bcm47xx_part: TRX offset : 0
bcm47xx_part: Updating TRX offsets and length:
bcm47xx_part: old trx = [0x0000001c, 0x00000968, 0x000ec800], len=0x002d1000 crc32=0x0b0fa919
bcm47xx_part: new trx = [0x0000001c, 0x00000968, 0x000ec800], len=0x000ec800 crc32=0x92014f46
bcm47xx_part: Done
4 bcm47xx partitions found on MTD device Physically mapped flash
Creating 4 MTD partitions on "Physically mapped flash":
0x000000000000-0x000000020000 : "cfe"
0x000000020000-0x0000007f0000 : "linux"
0x00000010c800-0x0000007f0000 : "rootfs"
mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=2B0000, len=540000
0x0000002b0000-0x0000007f0000 : "rootfs_data"
0x0000007f0000-0x000000800000 : "nvram"
bcm47xx_sflash: error registering platform driver: -19
b44: b44.c:v2.0
b44 ssb0:0: eth0: Broadcom 44xx/47xx 10/100BaseT Ethernet 00:24:8c:49:f2:68
BCM47xx Watchdog Timer enabled (30 seconds, nowayout)
TCP westwood registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8
VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
Freeing unused kernel memory: 156k freed
diag: Detected 'ASUS WL-500g Premium V2'
b44 ssb0:0: eth0: Link is up at 100 Mbps, full duplex
b44 ssb0:0: eth0: Flow control is off for TX and off for RX
roboswitch: Probing device eth0: found a 5325! It's a 5350.
- preinit -
Press the [f] key and hit [enter] to enter failsafe mode
- regular preinit -
jffs2 not ready yet; using ramdisk
- init -
b44 ssb0:0: eth0: powering down PHY
Please press Enter to activate this console. b44 ssb0:0: eth0: Link is up at 100 Mbps, full duplex
b44 ssb0:0: eth0: Flow control is off for TX and off for RX
Compat-wireless backport release: compat-wireless-2011-08-25
Backport based on wireless-testing.git master-2011-08-26
cfg80211: Calling CRDA to update world regulatory domain
SCSI subsystem initialized
device eth0.0 entered promiscuous mode
device eth0 entered promiscuous mode
br-lan: port 1(eth0.0) entering forwarding state
br-lan: port 1(eth0.0) entering forwarding state
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
b43-phy0: Broadcom 5354 WLAN found (core revision 13)
Broadcom 43xx driver loaded [ Features: PNL ]
Broadcom 43xx-legacy driver loaded [ Features: PLID ]
PPP generic driver version 2.4.2
ip_tables: (C) 2000-2006 Netfilter Core Team
cfg80211: World regulatory domain updated:
cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
NET: Registered protocol family 24
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
nf_conntrack version 0.5.0 (461 buckets, 1844 max)
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ohci_hcd ssb0:1: SSB OHCI Controller
ohci_hcd ssb0:1: new USB bus registered, assigned bus number 1
ohci_hcd ssb0:1: irq 6, io mem 0x18003000
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd ssb0:1: SSB EHCI Controller
ohci_hcd ssb0:1: new USB bus registered, assigned bus number 2
ohci_hcd ssb0:1: irq 6, io mem 0x18003800
ohci_hcd ssb0:1: USB 0.0 started, EHCI 1.00
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
uhci_hcd: USB Universal Host Controller Interface driver
usbcore: registered new interface driver cdc_acm
cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
usb 1-1: new full speed USB device number 2 using ohci_hcd
usbcore: registered new interface driver usbserial
USB Serial support registered for generic
usb 1-1: device descriptor read/64, error -62
usb 1-1: device descriptor read/64, error -62
usb 1-1: new full speed USB device number 3 using ohci_hcd
usb 1-1: device descriptor read/64, error -62
usb 1-1: device descriptor read/64, error -62
usb 1-1: new full speed USB device number 4 using ohci_hcd
usb 1-1: device not accepting address 4, error -62
usb 1-1: new full speed USB device number 5 using ohci_hcd
usb 1-1: device not accepting address 5, error -62
hub 1-0:1.0: unable to enumerate USB device on port 1
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial Driver core
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usbcore: registered new interface driver ums-alauda
usbcore: registered new interface driver ums-cypress
usbcore: registered new interface driver ums-datafab
usbcore: registered new interface driver ums-freecom
usbcore: registered new interface driver ums-isd200
usbcore: registered new interface driver ums-jumpshot
usbcore: registered new interface driver ums-karma
usbcore: registered new interface driver ums-sddr09
usbcore: registered new interface driver ums-sddr55
usbcore: registered new interface driver ums-usbat
usbcore: registered new interface driver asix
usbcore: registered new interface driver cdc_ether
usbcore: registered new interface driver rndis_host
USB Serial support registered for GSM modem (1-port)
usbcore: registered new interface driver option
option: v0.7.2:USB Driver for GSM modems
USB Serial support registered for pl2303
usbcore: registered new interface driver pl2303
pl2303: Prolific PL2303 USB to serial adaptor driver
jffs2_scan_eraseblock(): End of filesystem marker found at 0x0
jffs2_build_filesystem(): unlocking the mtd device... done.
jffs2_build_filesystem(): erasing all blocks after the end marker... done.
JFFS2 notice: (1068) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
^[[6;5~^H^H^H^H^H^H^H^H^H^H^H
BusyBox v1.18.5 (2011-08-31 14:47:04 MSK) built-in shell (ash)
Enter 'help' for a list of built-in commands.
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
ATTITUDE ADJUSTMENT (bleeding edge, r28137) ----------
* 1/4 oz Vodka Pour all ingredients into mixing
* 1/4 oz Gin tin with ice, strain into glass.
* 1/4 oz Amaretto
* 1/4 oz Triple sec
* 1/4 oz Peach schnapps
* 1/4 oz Sour mix
* 1 splash Cranberry juice
-----------------------------------------------------
root@OpenWrt:/# cat /proc/bus/usb/devices
T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=480 MxCh= 2
B: Alloc= 0/800 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 2.00 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0002 Rev= 3.00
S: Manufacturer=Linux 3.0.3 ssb-usb-ehci
S: Product=SSB EHCI Controller
S: SerialNumber=ssb0:1
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 4 Ivl=256ms
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1d6b ProdID=0001 Rev= 3.00
S: Manufacturer=Linux 3.0.3 ssb-usb-ohci
S: Product=SSB OHCI Controller
S: SerialNumber=ssb0:1
C:* #Ifs= 1 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
signature.asc
Description: PGP signature
_______________________________________________ openwrt-devel mailing list openwrt-devel@lists.openwrt.org https://lists.openwrt.org/mailman/listinfo/openwrt-devel
