Here the kernel output with debugging enabled ...
b44: eth0: Flow control is off for TX and off for RX.
ocf: module license 'BSD' taints kernel.
Disabling lock debugging due to kernel taint
Kernel bug detected[#1]:
Cpu 0
$ 0 : 00000000 00000030 00000001 00000001
$ 4 : 00010000 81801594 81d5fca0 00000010
$ 8 : 00000010 80005100 00000010 00000001
$12 : ffffffff 81c03f88 ffffffff 00000001
$16 : 81d5fca0 81d08700 81c09400 802f0000
$20 : 81d08700 00000000 81e33880 81d5fca0
$24 : 00000010 80018f74
$28 : 81d5e000 81d5fc60 7ffb33d8 800a11f0
Hi : fffffffd
Lo : 0a83f000
epc : 8009dfcc path_get+0xa8/0x14c
Tainted: P
ra : 800a11f0 vfs_path_lookup+0x3c/0x90
Status: 1000d803 KERNEL EXL IE
Cause : 00800034
PrId : 00029006 (Broadcom BCM3302)
Modules linked in: cryptodev(P+) ocf(P) deflate ecb cbc ext3 jbd usb_storage
sd_mod scsi_mod uhci_hcd ehci_hcd usbcore nls_utf8 nls_base switch_robo
switch_core diag
Process insmod (pid: 438, threadinfo=81d5e000, task=81d48a78, tls=00000000)
Stack : 1000d800 8002b9ec 81c6e5a0 802a2f40 81d5fde8 81e33880 81c09400
8016bde0
00000000 81c04700 81c04704 00000000 81d5fca0 00000000 00000000
00002180
81c0c5a0 81801594 00000010 81d5fdeb ffffffff 81d5fcd0 00000000 00000010
00000001 00000000 00000046 00000000 fffffff9 1000d801 00000000 00000001
00000000 00000003 00000ba2 00000000 81cdfa80 81cdfa84 00000ba0
8012aae8
...
Call Trace:
[<8009dfcc>] path_get+0xa8/0x14c
[<800a11f0>] vfs_path_lookup+0x3c/0x90
[<8016bde0>] devtmpfs_create_node+0xd0/0x318
[<80165518>] device_add+0x178/0x550
[<801659b8>] device_create_vargs+0xa0/0xe8
[<80165a20>] device_create+0x20/0x2c
[<8015b764>] misc_register+0x134/0x194
[<81f9f040>] init_module+0x40/0x68 [cryptodev]
[<8000d5c8>] do_one_initcall+0x70/0x1f4
[<800571fc>] sys_init_module+0xe0/0x224
[<80003230>] stack_done+0x20/0x3c
Code: 00000000 8ca20000 2c420001 <00028036> 3c03802e 8c624888 3c040001
00441024 10400008
IRQ 2/ubsec_ssb: IRQF_DISABLED is not guaranteed on shared IRQs
Sentry5(tm) ROBOGateway(tm) IPSec Core at IRQ 2
ubsec_ssb: DES 3DES AES128 AES192 AES256 MD5_HMAC SHA1_HMAC
greets
Am Donnerstag 07 Januar 2010 04:25:20 schrieb puchu:
> Hi,
>
> this patch updates brcm47xx to 2.6.32
> it works nice when i boot from flash but when i boot from a usbdisk
> ubsec_ssb seems to create a kernel bug ....
>
>
> here is the complete dmesg output when i boot from flash....
>
> Linux version 2.6.32.2 (pu...@tux) (gcc version 4.3.3 (GCC) ) #1 Thu Jan 7
> 03:56:54 CET 2010
> CPU revision is: 00029006 (Broadcom BCM3302)
> ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x03, vendor 0x4243)
> ssb: Core 1 found: Fast Ethernet (cc 0x806, rev 0x06, vendor 0x4243)
> ssb: Core 2 found: Fast Ethernet (cc 0x806, rev 0x06, vendor 0x4243)
> ssb: Core 3 found: USB 1.1 Hostdev (cc 0x808, rev 0x03, vendor 0x4243)
> ssb: Core 4 found: PCI (cc 0x804, rev 0x08, vendor 0x4243)
> ssb: Core 5 found: MIPS 3302 (cc 0x816, rev 0x03, vendor 0x4243)
> ssb: Core 6 found: V90 (cc 0x807, rev 0x02, vendor 0x4243)
> ssb: Core 7 found: IPSEC (cc 0x80B, rev 0x00, vendor 0x4243)
> ssb: Core 8 found: MEMC SDRAM (cc 0x80F, rev 0x02, vendor 0x4243)
> ssb: Initializing MIPS core...
> ssb: set_irq: core 0x0806, irq 4 => 4
> ssb: set_irq: core 0x0806, irq 5 => 5
> ssb: set_irq: core 0x0808, irq 6 => 2
> ssb: set_irq: core 0x0804, irq 2 => 6
> ssb: after irq reconfiguration
> ssb: core 0x0800, irq : 2(S) 3* 4 5 6 D I
> ssb: core 0x0806, irq : 2(S) 3 4* 5 6 D I
> ssb: core 0x0806, irq : 2(S) 3 4 5* 6 D I
> ssb: core 0x0808, irq : 2(S)* 3 4 5 6 D I
> ssb: core 0x0804, irq : 2(S) 3 4 5 6* D I
> ssb: core 0x0816, irq : 2(S)* 3 4 5 6 D I
> ssb: core 0x0807, irq : 2(S)* 3 4 5 6 D I
> ssb: core 0x080b, irq : 2(S)* 3 4 5 6 D I
> ssb: core 0x080f, irq : 2(S) 3 4 5 6 D I*
> ssb: Sonics Silicon Backplane found at address 0x18000000
> Serial init done.
> Determined physical RAM map:
> memory: 02000000 @ 00000000 (usable)
> Initrd not found or empty - disabling initrd
> Zone PFN ranges:
> Normal 0x00000000 -> 0x00002000
> Movable zone start PFN for each node
> early_node_map[1] active PFN ranges
> 0: 0x00000000 -> 0x00002000
> On node 0 totalpages: 8192
> free_area_init_node: node 0, pgdat 80293340, node_mem_map 81000000
> Normal zone: 64 pages used for memmap
> Normal zone: 0 pages reserved
> Normal zone: 8128 pages, LIFO batch:0
> Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
> Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd
> PID hash table entries: 128 (order: -3, 512 bytes)
> Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
> Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
> Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
> Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
> Memory: 29572k/32768k available (2223k kernel code, 3196k reserved, 411k
> data, 136k init, 0k highmem)
> Hierarchical RCU implementation.
> NR_IRQS:128
> console [ttyS0] enabled
> Calibrating delay loop... 263.16 BogoMIPS (lpj=526336)
> Mount-cache hash table entries: 512
> devtmpfs: initialized
> NET: Registered protocol family 16
> bio: create slab <bio-0> at 0
> Switching to clocksource MIPS
> ssb: PCIcore in host mode found
> PCI: Fixing up bridge 0000:00:00.0
> PCI: Setting latency timer of device 0000:00:00.0 to 64
> PCI: Fixing up device 0000:00:00.0
> PCI: Fixing latency timer of device 0000:00:00.0 to 168
> pci 0000:00:00.0: reg 10 32bit mmio: [0x000000-0x001fff]
> pci 0000:00:00.0: reg 14 32bit mmio pref: [0x000000-0x7ffffff]
> pci 0000:00:03.0: reg 20 io port: [0xfce0-0xfcff]
> pci 0000:00:03.0: supports D1 D2
> pci 0000:00:03.0: PME# supported from D0 D1 D2 D3hot
> pci 0000:00:03.0: PME# disabled
> pci 0000:00:03.1: reg 20 io port: [0xfce0-0xfcff]
> pci 0000:00:03.1: supports D1 D2
> pci 0000:00:03.1: PME# supported from D0 D1 D2 D3hot
> pci 0000:00:03.1: PME# disabled
> pci 0000:00:03.2: reg 10 32bit mmio: [0x000000-0x0000ff]
> pci 0000:00:03.2: supports D1 D2
> pci 0000:00:03.2: PME# supported from D0 D1 D2 D3hot
> pci 0000:00:03.2: PME# disabled
> NET: Registered protocol family 2
> IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
> TCP established hash table entries: 1024 (order: 1, 8192 bytes)
> TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
> TCP: Hash tables configured (established 1024 bind 1024)
> TCP reno registered
> NET: Registered protocol family 1
> squashfs: version 4.0 (2009/01/31) Phillip Lougher
> Registering mini_fo version $Id$
> JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
> msgmni has been set to 57
> alg: No test for stdrng (krng)
> io scheduler noop registered
> io scheduler deadline registered (default)
> Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
> serial8250: ttyS0 at MMIO 0xb8000300 (irq = 3) is a 16550A
> serial8250: ttyS1 at MMIO 0xb8000400 (irq = 3) is a 16550A
> serial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 3) is a 16550A
> serial8250.0: ttyS1 at MMIO 0xb8000400 (irq = 3) is a 16550A
> flash init: 0x1c000000 0x02000000
> Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
> Physically mapped flash: Found an alias at 0x800000 for the chip at 0x0
> Physically mapped flash: Found an alias at 0x1000000 for the chip at 0x0
> Physically mapped flash: Found an alias at 0x1800000 for the chip at 0x0
> Amd/Fujitsu Extended Query Table at 0x0040
> Physically mapped flash: CFI does not contain boot bank location. Assuming
> top. number of CFI chips: 1
> cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
> Flash device: 0x800000 at 0x1fc00000
> bootloader size: 262144
> Creating 4 MTD partitions on "Physically mapped flash":
> 0x000000000000-0x000000040000 : "cfe"
> 0x000000040000-0x0000007f0000 : "linux"
> 0x000000119000-0x0000007f0000 : "rootfs"
> mtd: partition "rootfs" must either start or end on erase block boundary or
> be smaller than an erase block -- forcing read-only
> mtd: partition "rootfs" set to be root filesystem
> mtd: partition "rootfs_data" created automatically, ofs=5B0000, len=240000
> 0x0000005b0000-0x0000007f0000 : "rootfs_data"
> 0x0000007f0000-0x000000800000 : "nvram"
> b44.c:v2.0
> eth0: Broadcom 44xx/47xx 10/100BaseT Ethernet 00:18:f3:85:62:00
> b44: eth1: PHY Reset would not complete.
> eth1: Broadcom 44xx/47xx 10/100BaseT Ethernet 40:10:18:00:00:2d
> BCM47xx Watchdog Timer enabled (30 seconds, nowayout)
> TCP westwood registered
> NET: Registered protocol family 17
> 802.1Q VLAN Support v1.8 Ben Greear <gree...@candelatech.com>
> All bugs added by David S. Miller <da...@redhat.com>
> VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
> devtmpfs: mounted
> Freeing unused kernel memory: 136k freed
> diag: Detected 'ASUS WL-500g Premium'
> b44: eth0: Link is up at 100 Mbps, full duplex.
> b44: eth0: Flow control is off for TX and off for RX.
> roboswitch: Probing device eth0: found a 5325! It's a 5350.
> b44: eth0: powering down PHY
> mini_fo: using base directory: /
> mini_fo: using storage directory: /jffs
> usbcore: registered new interface driver usbfs
> usbcore: registered new interface driver hub
> usbcore: registered new device driver usb
> ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
> PCI: Enabling device 0000:00:03.2 (0000 -> 0002)
> PCI: Fixing up device 0000:00:03.2
> ehci_hcd 0000:00:03.2: EHCI Host Controller
> ehci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 1
> ehci_hcd 0000:00:03.2: Enabling legacy PCI PM
> ehci_hcd 0000:00:03.2: irq 6, io mem 0x40000000
> ehci_hcd 0000:00:03.2: USB 2.0 started, EHCI 1.00
> usb usb1: configuration #1 chosen from 1 choice
> hub 1-0:1.0: USB hub found
> hub 1-0:1.0: 4 ports detected
> uhci_hcd: USB Universal Host Controller Interface driver
> PCI: Enabling device 0000:00:03.0 (0000 -> 0001)
> PCI: Fixing up device 0000:00:03.0
> uhci_hcd 0000:00:03.0: UHCI Host Controller
> uhci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 2
> uhci_hcd 0000:00:03.0: irq 6, io base 0x00000100
> usb usb2: configuration #1 chosen from 1 choice
> hub 2-0:1.0: USB hub found
> hub 2-0:1.0: 2 ports detected
> PCI: Enabling device 0000:00:03.1 (0000 -> 0001)
> PCI: Fixing up device 0000:00:03.1
> uhci_hcd 0000:00:03.1: UHCI Host Controller
> uhci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 3
> uhci_hcd 0000:00:03.1: irq 6, io base 0x00000120
> usb usb3: configuration #1 chosen from 1 choice
> hub 3-0:1.0: USB hub found
> hub 3-0:1.0: 2 ports detected
> SCSI subsystem initialized
> usb 1-1: new high speed USB device using ehci_hcd and address 2
> usb 1-1: configuration #1 chosen from 1 choice
> Initializing USB Mass Storage driver...
> scsi0 : SCSI emulation for USB Mass Storage devices
> usbcore: registered new interface driver usb-storage
> USB Mass Storage support registered.
> usb-storage: device found at 2
> usb-storage: waiting for device to settle before scanning
> scsi 0:0:0:0: Direct-Access SEAGATE ST660211USB 4.06 PQ: 0 ANSI:
> 2 sd 0:0:0:0: [sda] 11719008 512-byte logical blocks: (6.00 GB/5.58 GiB)
> usb-storage: device scan complete
> sd 0:0:0:0: [sda] Write Protect is off
> sd 0:0:0:0: [sda] Mode Sense: 73 00 00 08
> sd 0:0:0:0: [sda] Assuming drive cache: write through
> sd 0:0:0:0: [sda] Assuming drive cache: write through
> sda: sda1 sda2 sda3 sda4
> sd 0:0:0:0: [sda] Assuming drive cache: write through
> sd 0:0:0:0: [sda] Attached SCSI removable disk
> kjournald starting. Commit interval 5 seconds
> EXT3 FS on sda1, internal journal
> EXT3-fs: mounted filesystem with writeback data mode.
> b44: eth0: Link is up at 100 Mbps, full duplex.
> b44: eth0: Flow control is off for TX and off for RX.
> ocf: module license 'BSD' taints kernel.
> Disabling lock debugging due to kernel taint
> IRQ 2/ubsec_ssb: IRQF_DISABLED is not guaranteed on shared IRQs
> Sentry5(tm) ROBOGateway(tm) IPSec Core at IRQ 2
> ubsec_ssb: DES 3DES AES128 AES192 AES256 MD5_HMAC SHA1_HMAC
> RPC: Registered udp transport module.
> RPC: Registered tcp transport module.
> RPC: Registered tcp NFSv4.1 backchannel transport module.
> Installing knfsd (copyright (C) 1996 o...@monad.swb.de).
> ip_tables: (C) 2000-2006 Netfilter Core Team
> nf_conntrack version 0.5.0 (464 buckets, 1856 max)
> xt_time: kernel timezone is -0000
> nf_conntrack_rtsp v0.6.21 loading
> nf_nat_rtsp v0.6.21 loading
>
>
> and here the output when i boot from a usbdisk
>
> Linux version 2.6.32.2 (pu...@tux) (gcc version 4.3.3 (GCC) ) #1 Thu Jan 7
> 03:56:54 CET 2010
> CPU revision is: 00029006 (Broadcom BCM3302)
> ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x03, vendor 0x4243)
> ssb: Core 1 found: Fast Ethernet (cc 0x806, rev 0x06, vendor 0x4243)
> ssb: Core 2 found: Fast Ethernet (cc 0x806, rev 0x06, vendor 0x4243)
> ssb: Core 3 found: USB 1.1 Hostdev (cc 0x808, rev 0x03, vendor 0x4243)
> ssb: Core 4 found: PCI (cc 0x804, rev 0x08, vendor 0x4243)
> ssb: Core 5 found: MIPS 3302 (cc 0x816, rev 0x03, vendor 0x4243)
> ssb: Core 6 found: V90 (cc 0x807, rev 0x02, vendor 0x4243)
> ssb: Core 7 found: IPSEC (cc 0x80B, rev 0x00, vendor 0x4243)
> ssb: Core 8 found: MEMC SDRAM (cc 0x80F, rev 0x02, vendor 0x4243)
> ssb: Initializing MIPS core...
> ssb: set_irq: core 0x0806, irq 4 => 4
> ssb: set_irq: core 0x0806, irq 5 => 5
> ssb: set_irq: core 0x0808, irq 6 => 2
> ssb: set_irq: core 0x0804, irq 2 => 6
> ssb: after irq reconfiguration
> ssb: core 0x0800, irq : 2(S) 3* 4 5 6 D I
> ssb: core 0x0806, irq : 2(S) 3 4* 5 6 D I
> ssb: core 0x0806, irq : 2(S) 3 4 5* 6 D I
> ssb: core 0x0808, irq : 2(S)* 3 4 5 6 D I
> ssb: core 0x0804, irq : 2(S) 3 4 5 6* D I
> ssb: core 0x0816, irq : 2(S)* 3 4 5 6 D I
> ssb: core 0x0807, irq : 2(S)* 3 4 5 6 D I
> ssb: core 0x080b, irq : 2(S)* 3 4 5 6 D I
> ssb: core 0x080f, irq : 2(S) 3 4 5 6 D I*
> ssb: Sonics Silicon Backplane found at address 0x18000000
> Serial init done.
> Determined physical RAM map:
> memory: 02000000 @ 00000000 (usable)
> Initrd not found or empty - disabling initrd
> Zone PFN ranges:
> Normal 0x00000000 -> 0x00002000
> Movable zone start PFN for each node
> early_node_map[1] active PFN ranges
> 0: 0x00000000 -> 0x00002000
> On node 0 totalpages: 8192
> free_area_init_node: node 0, pgdat 80293340, node_mem_map 81000000
> Normal zone: 64 pages used for memmap
> Normal zone: 0 pages reserved
> Normal zone: 8128 pages, LIFO batch:0
> Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
> Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd
> PID hash table entries: 128 (order: -3, 512 bytes)
> Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
> Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
> Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
> Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
> Memory: 29572k/32768k available (2223k kernel code, 3196k reserved, 411k
> data, 136k init, 0k highmem)
> Hierarchical RCU implementation.
> NR_IRQS:128
> console [ttyS0] enabled
> Calibrating delay loop... 263.16 BogoMIPS (lpj=526336)
> Mount-cache hash table entries: 512
> devtmpfs: initialized
> NET: Registered protocol family 16
> bio: create slab <bio-0> at 0
> Switching to clocksource MIPS
> ssb: PCIcore in host mode found
> PCI: Fixing up bridge 0000:00:00.0
> PCI: Setting latency timer of device 0000:00:00.0 to 64
> PCI: Fixing up device 0000:00:00.0
> PCI: Fixing latency timer of device 0000:00:00.0 to 168
> pci 0000:00:00.0: reg 10 32bit mmio: [0x000000-0x001fff]
> pci 0000:00:00.0: reg 14 32bit mmio pref: [0x000000-0x7ffffff]
> pci 0000:00:03.0: reg 20 io port: [0xfce0-0xfcff]
> pci 0000:00:03.0: supports D1 D2
> pci 0000:00:03.0: PME# supported from D0 D1 D2 D3hot
> pci 0000:00:03.0: PME# disabled
> pci 0000:00:03.1: reg 20 io port: [0xfce0-0xfcff]
> pci 0000:00:03.1: supports D1 D2
> pci 0000:00:03.1: PME# supported from D0 D1 D2 D3hot
> pci 0000:00:03.1: PME# disabled
> pci 0000:00:03.2: reg 10 32bit mmio: [0x000000-0x0000ff]
> pci 0000:00:03.2: supports D1 D2
> pci 0000:00:03.2: PME# supported from D0 D1 D2 D3hot
> pci 0000:00:03.2: PME# disabled
> NET: Registered protocol family 2
> IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
> TCP established hash table entries: 1024 (order: 1, 8192 bytes)
> TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
> TCP: Hash tables configured (established 1024 bind 1024)
> TCP reno registered
> NET: Registered protocol family 1
> squashfs: version 4.0 (2009/01/31) Phillip Lougher
> Registering mini_fo version $Id$
> JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
> msgmni has been set to 57
> alg: No test for stdrng (krng)
> io scheduler noop registered
> io scheduler deadline registered (default)
> Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
> serial8250: ttyS0 at MMIO 0xb8000300 (irq = 3) is a 16550A
> serial8250: ttyS1 at MMIO 0xb8000400 (irq = 3) is a 16550A
> serial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 3) is a 16550A
> serial8250.0: ttyS1 at MMIO 0xb8000400 (irq = 3) is a 16550A
> flash init: 0x1c000000 0x02000000
> Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
> Physically mapped flash: Found an alias at 0x800000 for the chip at 0x0
> Physically mapped flash: Found an alias at 0x1000000 for the chip at 0x0
> Physically mapped flash: Found an alias at 0x1800000 for the chip at 0x0
> Amd/Fujitsu Extended Query Table at 0x0040
> Physically mapped flash: CFI does not contain boot bank location. Assuming
> top. number of CFI chips: 1
> cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
> Flash device: 0x800000 at 0x1fc00000
> bootloader size: 262144
> Creating 4 MTD partitions on "Physically mapped flash":
> 0x000000000000-0x000000040000 : "cfe"
> 0x000000040000-0x0000007f0000 : "linux"
> 0x000000119000-0x0000007f0000 : "rootfs"
> mtd: partition "rootfs" must either start or end on erase block boundary or
> be smaller than an erase block -- forcing read-only
> mtd: partition "rootfs" set to be root filesystem
> mtd: partition "rootfs_data" created automatically, ofs=5B0000, len=240000
> 0x0000005b0000-0x0000007f0000 : "rootfs_data"
> 0x0000007f0000-0x000000800000 : "nvram"
> b44.c:v2.0
> eth0: Broadcom 44xx/47xx 10/100BaseT Ethernet 00:18:f3:85:62:00
> b44: eth1: PHY Reset would not complete.
> eth1: Broadcom 44xx/47xx 10/100BaseT Ethernet 40:10:18:00:00:2d
> BCM47xx Watchdog Timer enabled (30 seconds, nowayout)
> TCP westwood registered
> NET: Registered protocol family 17
> 802.1Q VLAN Support v1.8 Ben Greear <gree...@candelatech.com>
> All bugs added by David S. Miller <da...@redhat.com>
> VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
> devtmpfs: mounted
> Freeing unused kernel memory: 136k freed
> diag: Detected 'ASUS WL-500g Premium'
> b44: eth0: Link is up at 100 Mbps, full duplex.
> b44: eth0: Flow control is off for TX and off for RX.
> roboswitch: Probing device eth0: found a 5325! It's a 5350.
> b44: eth0: powering down PHY
> mini_fo: using base directory: /
> mini_fo: using storage directory: /jffs
> usbcore: registered new interface driver usbfs
> usbcore: registered new interface driver hub
> usbcore: registered new device driver usb
> ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
> PCI: Enabling device 0000:00:03.2 (0000 -> 0002)
> PCI: Fixing up device 0000:00:03.2
> ehci_hcd 0000:00:03.2: EHCI Host Controller
> ehci_hcd 0000:00:03.2: new USB bus registered, assigned bus number 1
> ehci_hcd 0000:00:03.2: Enabling legacy PCI PM
> ehci_hcd 0000:00:03.2: irq 6, io mem 0x40000000
> ehci_hcd 0000:00:03.2: USB 2.0 started, EHCI 1.00
> usb usb1: configuration #1 chosen from 1 choice
> hub 1-0:1.0: USB hub found
> hub 1-0:1.0: 4 ports detected
> uhci_hcd: USB Universal Host Controller Interface driver
> PCI: Enabling device 0000:00:03.0 (0000 -> 0001)
> PCI: Fixing up device 0000:00:03.0
> uhci_hcd 0000:00:03.0: UHCI Host Controller
> uhci_hcd 0000:00:03.0: new USB bus registered, assigned bus number 2
> uhci_hcd 0000:00:03.0: irq 6, io base 0x00000100
> usb usb2: configuration #1 chosen from 1 choice
> hub 2-0:1.0: USB hub found
> hub 2-0:1.0: 2 ports detected
> PCI: Enabling device 0000:00:03.1 (0000 -> 0001)
> PCI: Fixing up device 0000:00:03.1
> uhci_hcd 0000:00:03.1: UHCI Host Controller
> uhci_hcd 0000:00:03.1: new USB bus registered, assigned bus number 3
> uhci_hcd 0000:00:03.1: irq 6, io base 0x00000120
> usb usb3: configuration #1 chosen from 1 choice
> hub 3-0:1.0: USB hub found
> hub 3-0:1.0: 2 ports detected
> SCSI subsystem initialized
> usb 1-1: new high speed USB device using ehci_hcd and address 2
> usb 1-1: configuration #1 chosen from 1 choice
> Initializing USB Mass Storage driver...
> scsi0 : SCSI emulation for USB Mass Storage devices
> usbcore: registered new interface driver usb-storage
> USB Mass Storage support registered.
> usb-storage: device found at 2
> usb-storage: waiting for device to settle before scanning
> scsi 0:0:0:0: Direct-Access SEAGATE ST660211USB 4.06 PQ: 0 ANSI:
> 2 sd 0:0:0:0: [sda] 11719008 512-byte logical blocks: (6.00 GB/5.58 GiB)
> usb-storage: device scan complete
> sd 0:0:0:0: [sda] Write Protect is off
> sd 0:0:0:0: [sda] Mode Sense: 73 00 00 08
> sd 0:0:0:0: [sda] Assuming drive cache: write through
> sd 0:0:0:0: [sda] Assuming drive cache: write through
> sda: sda1 sda2 sda3 sda4
> sd 0:0:0:0: [sda] Assuming drive cache: write through
> sd 0:0:0:0: [sda] Attached SCSI removable disk
> kjournald starting. Commit interval 5 seconds
> EXT3 FS on sda1, internal journal
> EXT3-fs: mounted filesystem with writeback data mode.
> kjournald starting. Commit interval 5 seconds
> EXT3 FS on sda2, internal journal
> EXT3-fs: mounted filesystem with writeback data mode.
> kjournald starting. Commit interval 5 seconds
> EXT3 FS on sda4, internal journal
> EXT3-fs: mounted filesystem with writeback data mode.
> Adding 45872k swap on /dev/sda3. Priority:-1 extents:1 across:45872k
> b44: eth0: Link is up at 100 Mbps, full duplex.
> b44: eth0: Flow control is off for TX and off for RX.
> ocf: module license 'BSD' taints kernel.
> Disabling lock debugging due to kernel taint
> Kernel bug detected[#1]:
> Cpu 0
> $ 0 : 00000000 00000030 00000001 00000001
> $ 4 : 00010000 81801594 81d21ca0 00000010
> $ 8 : 00000010 80005100 00000010 00000000
> $12 : ffffffff 81c03108 ffffffff 00000001
> $16 : 81d21ca0 81cda400 81c09400 802d0000
> $20 : 81cda400 00000000 81eea880 81d21ca0
> $24 : 00000010 80018bfc
> $28 : 81d20000 81d21c60 7feebb98 8009eccc
> Hi : fffffffd
> Lo : 0a83f000
> epc : 8009baa8 0x8009baa8
> Tainted: P
> ra : 8009eccc 0x8009eccc
> Status: 1000d803 KERNEL EXL IE
> Cause : 00800034
> PrId : 00029006 (Broadcom BCM3302)
> Modules linked in: cryptodev(P+) ocf(P) deflate ecb cbc ext3 jbd
> usb_storage sd_mod scsi_mod uhci_hcd ehci_hcd usbcore nls_utf8 nls_base
> switch_robo switch_core diag
> Process insmod (pid: 449, threadinfo=81d20000, task=81da7630, tls=00000000)
> Stack : ffffffff 80063a5c 00000001 8005352c 81d21de8 81eea880 81c09400
> 80169710 00000000 81c04700 81c04704 00000000 81d21ca0 81d21cb0 00000000
> 00002180
> 81c0c5a0 81801594 ffffffff ffffffff ffffffff 00000000 8028d560
> 00000010 00000001 00000000 00000002 00000002 ffffffff 00000000 00000000
> 00000001 00000000 81c04700 81c04704 00000000 802d0ec0 81d21d10 81d21d68
> 801282bc
> ...
> Call Trace:[<80063a5c>] 0x80063a5c
> [<8005352c>] 0x8005352c
> [<80169710>] 0x80169710
> [<801282bc>] 0x801282bc
> [<801282bc>] 0x801282bc
> [<800e1dd0>] 0x800e1dd0
> [<800a86b4>] 0x800a86b4
> [<800a8754>] 0x800a8754
> [<800e2854>] 0x800e2854
> [<800e2854>] 0x800e2854
> [<800e263c>] 0x800e263c
> [<800e3dec>] 0x800e3dec
> [<80162e48>] 0x80162e48
> [<80160030>] 0x80160030
> [<801632e8>] 0x801632e8
> [<80163350>] 0x80163350
> [<80055468>] 0x80055468
> [<801590e8>] 0x801590e8
> [<81f1f000>] 0x81f1f000
> [<81f1f040>] 0x81f1f040
> [<8000d5e0>] 0x8000d5e0
> [<8004349c>] 0x8004349c
> [<80055a70>] 0x80055a70
> [<80080850>] 0x80080850
> [<8008f860>] 0x8008f860
> [<80003230>] 0x80003230
>
>
> Code: 00000000 8ca20000 2c420001 <00028036> 3c03802c 8c620888 3c040001
> 00441024 10400008
> IRQ 2/ubsec_ssb: IRQF_DISABLED is not guaranteed on shared IRQs
> Sentry5(tm) ROBOGateway(tm) IPSec Core at IRQ 2
> ubsec_ssb: DES 3DES AES128 AES192 AES256 MD5_HMAC SHA1_HMAC
> RPC: Registered udp transport module.
> RPC: Registered tcp transport module.
> RPC: Registered tcp NFSv4.1 backchannel transport module.
> Installing knfsd (copyright (C) 1996 o...@monad.swb.de).
> ip_tables: (C) 2000-2006 Netfilter Core Team
> nf_conntrack version 0.5.0 (464 buckets, 1856 max)
> xt_time: kernel timezone is -0000
> nf_conntrack_rtsp v0.6.21 loading
> nf_nat_rtsp v0.6.21 loading
>
> it worked nice under 2.6.30
>
> maybe someone knows a way to fix this
>
> greets
>
_______________________________________________
openwrt-devel mailing list
openwrt-devel@lists.openwrt.org
https://lists.openwrt.org/mailman/listinfo/openwrt-devel
