My glance-api-paste.ini already had the credentials when I posted the problem. Also, my python-glance package is Essex, just like the other openstack packages. After giving *glance -d index* as input, I noticed something that's pretty much obvious: The error comes from the response to the attempt at authenticating the user. I'm gonna double-check the credentials in the config files, then gonna report here.
2012/10/4 Jon Thomas <jtho...@redhat.com> > On Thu, 2012-10-04 at 11:41 -0500, Ahmed Al-Mehdi wrote: > > Hi Janis, > > > > > > Just fyi, in the Folsom release the lines with the "%…%" in > > glance-api.conf and glance-api-paste.ini are not present. Document > > instructs user to add the three relevant lines to [filter.authtoken] > > section. > > > It looked to me that there were some config file changes in folsom. > > glance index works fine for me and I have in glance-api-paste.ini > > [filter:authtoken] > paste.filter_factory = keystone.middleware.auth_token:filter_factory > delay_auth_decision = true > admin_tenant_name = service > admin_user = glance > admin_password = servicepass > > and in glance-api.conf there is no [filter:authtoken]. However there is > [keystone_authtoken], but it's unchanged > > [keystone_authtoken] > auth_host = 127.0.0.1 > auth_port = 35357 > auth_protocol = http > admin_tenant_name = %SERVICE_TENANT_NAME% > admin_user = %SERVICE_USER% > admin_password = %SERVICE_PASSWORD% > > Another possiblity for the 500 error might be that the > python-glanceclient package is essex, not folsom. I had a 500 error with > nova that was due to the python-novaclient package being essex, while > nova packages were folsom. > > > > > Regards, > > Ahmed. > > > > > > > > From: J?nis ?e??eris <janis.genge...@gmail.com> > > Date: Thursday, October 4, 2012 7:24 AM > > To: Daniel Oliveira <dvalbr...@gmail.com> > > Cc: "openstack@lists.launchpad.net" <openstack@lists.launchpad.net> > > Subject: Re: [Openstack] Just a newbie getting some error messages > > > > > > > > When you have fresh install you will usually have something like this > > in glance-api.conf > > > > > > [filter:authtoken] > > auth_host = 127.0.0.1 > > auth_port = 35357 > > auth_protocol = http > > admin_tenant_name = %SERVICE_TENANT_NAME% > > admin_user = %SERVICE_USER% > > admin_password = %SERVICE_PASSWORD% > > > > > > and something similar inside glance-api-paste.ini > > > > > > So if you have these lines with %SERVICE_USER%, %SERVICE_PASSWORD%, % > > SERVICE_TENANT_NAME%, you need to replace them all with real user > > credentials that have been configured in Keystone. > > > > > > Here you can see sample config files with the sections configured: > > > http://docs.openstack.org/trunk/openstack-compute/install/content/glance-api-paste-file.html > > > http://docs.openstack.org/trunk/openstack-compute/install/content/glance-api-conf-file.html > > > > On Thu, Oct 4, 2012 at 4:36 PM, Daniel Oliveira <dvalbr...@gmail.com> > > wrote: > > Hello Janis, > > > > > > I'm not sure if I understood what I should replace. Do you > > mean replacing, for example: > > > > > > the line > > admin_user = glance > > in the [filter:authtoken] section > > > > > > for the line > > admin_user = %glance? > > > > > > and so on for the other credentials? > > > > 2012/10/4 J?nis ?e??eris <janis.genge...@gmail.com> > > Hi Daniel, > > > > > > Do you have set up [filter:authtoken] section in > > glance-api-paste.ini? You need to replace the strings > > with percent signs with correct auth credentials. > > > > > > To get more precise output use, 'glance -d index', > > that will show additional debug information. > > > > On Thu, Oct 4, 2012 at 4:07 PM, Daniel Oliveira > > <dvalbr...@gmail.com> wrote: > > > > Hello, > > > > > > I've been trying to install OpenStack on a > > server by following the manual installation > > tutorial on openstack.org for Ubuntu Server > > 12.04 (and that's the OS I'm using, > > obviously). But when it comes to test whether > > Glance was installed successfully > > ( > http://docs.openstack.org/essex/openstack-compute/install/apt/content/images-verifying-install.html), > I get the following error message: > > > > > > Failed to show index. Got error: > > Unexpected responde: 500 > > > > > > The same happens when I try to do glance > > index, which I guess should produce no output > > instead. I really need some help on this, > > since I'm not that experient with linux. Sorry > > for any grammar errors, english is not my > > native language ^_^. Thanks in advance, > > > > > > -- > > My best regards, > > > > > > Daniel Oliveira. > > > > > > > > > > _______________________________________________ > > Mailing list: https://launchpad.net/~openstack > > Post to : openstack@lists.launchpad.net > > Unsubscribe : https://launchpad.net/~openstack > > More help : > > https://help.launchpad.net/ListHelp > > > > > > > > > > > > -- > > --janis > > > > > > > > > > -- > > My best regards, > > > > > > Daniel Oliveira. > > > > > > > > > > > > > > -- > > --janis > > _______________________________________________ > > Mailing list: https://launchpad.net/~openstack > > Post to : openstack@lists.launchpad.net > > Unsubscribe : https://launchpad.net/~openstack > > More help : https://help.launchpad.net/ListHelp > > > -- My best regards, Daniel Oliveira.
_______________________________________________ Mailing list: https://launchpad.net/~openstack Post to : openstack@lists.launchpad.net Unsubscribe : https://launchpad.net/~openstack More help : https://help.launchpad.net/ListHelp
