Hi,
in 3 tcl scripts the command "flash bank" has an underline character
between the 2 words.
tcl/board/at91rm9200-dk.cfg
tcl/board/imx27ads.cfg
tcl/board/logicpd_imx27.cfg
I cannot fully verify, since I do not have any of the target boards
involved, but this should generate an error message.
The patch in attachment should fix the issue.
Comments are welcome.
Best Regards,
Antonio Borneo
From 689969e6995020f46408e2ecf788023da2c88343 Mon Sep 17 00:00:00 2001
From: Antonio Borneo <borneo.anto...@gmail.com>
Date: Thu, 15 Apr 2010 17:11:01 +0800
Subject: [PATCH] TCL SCRIPTS: fix command name
Some tcl script has underline between the words "flash bank"
resulting in 'invalid command name "flash_bank"'.
Signed-off-by: Antonio Borneo <borneo.anto...@gmail.com>
---
tcl/board/at91rm9200-dk.cfg | 2 +-
tcl/board/imx27ads.cfg | 2 +-
tcl/board/logicpd_imx27.cfg | 2 +-
3 files changed, 3 insertions(+), 3 deletions(-)
diff --git a/tcl/board/at91rm9200-dk.cfg b/tcl/board/at91rm9200-dk.cfg
index af6e3df..402ed05 100644
--- a/tcl/board/at91rm9200-dk.cfg
+++ b/tcl/board/at91rm9200-dk.cfg
@@ -10,7 +10,7 @@ $_TARGETNAME configure -event reset-init { at91rm9200_dk_init }
#flash bank <name> <driver> <base> <size> <chip_width> <bus_width> <target>
set _FLASHNAME $_CHIPNAME.flash
-flash_bank $_FLASHNAME cfi 0x10000000 0x00200000 2 2 $_TARGETNAME
+flash bank $_FLASHNAME cfi 0x10000000 0x00200000 2 2 $_TARGETNAME
proc at91rm9200_dk_init { } {
diff --git a/tcl/board/imx27ads.cfg b/tcl/board/imx27ads.cfg
index 927647a..e705b1e 100644
--- a/tcl/board/imx27ads.cfg
+++ b/tcl/board/imx27ads.cfg
@@ -6,7 +6,7 @@ $_TARGETNAME configure -event reset-init { imx27ads_init }
# The IMX27 ADS board has a NOR flash on CS0
set _FLASHNAME $_CHIPNAME.flash
-flash_bank $_FLASHNAME cfi 0xc0000000 0x00200000 2 2 $_TARGETNAME
+flash bank $_FLASHNAME cfi 0xc0000000 0x00200000 2 2 $_TARGETNAME
proc imx27ads_init { } {
# This setup puts RAM at 0xA0000000
diff --git a/tcl/board/logicpd_imx27.cfg b/tcl/board/logicpd_imx27.cfg
index 02afc77..da0b462 100644
--- a/tcl/board/logicpd_imx27.cfg
+++ b/tcl/board/logicpd_imx27.cfg
@@ -3,7 +3,7 @@ source [find target/imx27.cfg]
# The Logic PD board has a NOR flash on CS0
set _FLASHNAME $_CHIPNAME.flash
-flash_bank $_FLASHNAME cfi 0xc0000000 0x00200000 2 2 $_TARGETNAME
+flash bank $_FLASHNAME cfi 0xc0000000 0x00200000 2 2 $_TARGETNAME
#
# FIX ME, Add support to
--
1.5.2.2
_______________________________________________
Openocd-development mailing list
Openocd-development@lists.berlios.de
https://lists.berlios.de/mailman/listinfo/openocd-development
