The semantics of "-work-area-virt 0" (or phys) changed with
the patch to require specifying physical or virtual work
area addresses. Specifying zero was previously a NOP. Now
it means that address zero is valid.
This patch addresses three related issues:
- MMU-less processors should never specify work-area-virt;
remove those specifications. Such processors include
ARM7TDMI, Cortex-M3, and ARM966.
- MMU-equipped processors *can* specify work-area-virt...
but zero won't be appropriate, except in mischievous
contexts (which hide null pointer exceptions).
Remove those specs from those processors too. If any of
those mappings is valid, someone will need to submit a
patch adding it ... along with a comment saying what OS
provides the mapping, and in which context. Example,
say "works with Linux 2.6.30+, in kernel mode". (Note
that ARM Linux doesn't map kernel memory to zero ...)
- Clarify docs on that "-virt" and other work area stuff.
Seems to me work-area-virt is quite problematic; not every
operating system provides such static mappings; if they do,
they're not in every MMU context...
---
doc/openocd.texi | 7 ++++++-
tcl/board/at91sam9g20-ek.cfg | 4 ++--
tcl/board/digi_connectcore_wi-9c.cfg | 2 +-
tcl/board/hitex_str9-comstick.cfg | 2 +-
tcl/board/linksys_nslu2.cfg | 2 +-
tcl/board/mini2440.cfg | 2 +-
tcl/board/pxa255_sst.cfg | 2 +-
tcl/board/str910-eval.cfg | 2 +-
tcl/board/zy1000.cfg | 2 +-
tcl/target/at91eb40a.cfg | 2 +-
tcl/target/at91r40008.cfg | 2 +-
tcl/target/at91rm9200.cfg | 2 +-
tcl/target/at91sam3uXX.cfg | 2 +-
tcl/target/at91sam7sx.cfg | 2 +-
tcl/target/at91sam9260.cfg | 2 +-
tcl/target/at91sam9260_ext_RAM_ext_flash.cfg | 2 +-
tcl/target/cs351x.cfg | 2 +-
tcl/target/epc9301.cfg | 2 +-
tcl/target/imx27.cfg | 4 +++-
tcl/target/is5114.cfg | 2 +-
tcl/target/lpc1768.cfg | 2 +-
tcl/target/lpc2103.cfg | 2 +-
tcl/target/lpc2124.cfg | 2 +-
tcl/target/lpc2129.cfg | 2 +-
tcl/target/lpc2148.cfg | 2 +-
tcl/target/lpc2294.cfg | 2 +-
tcl/target/lpc2378.cfg | 2 +-
tcl/target/lpc2478.cfg | 2 +-
tcl/target/mega128.cfg | 2 +-
tcl/target/omap5912.cfg | 2 +-
tcl/target/pic32mx.cfg | 2 +-
tcl/target/pxa270.cfg | 2 +-
tcl/target/sam7se512.cfg | 2 +-
tcl/target/sam7x256.cfg | 2 +-
tcl/target/samsung_s3c2410.cfg | 2 +-
tcl/target/samsung_s3c2440.cfg | 2 +-
tcl/target/stm32.cfg | 2 +-
tcl/target/str710.cfg | 2 +-
tcl/target/str730.cfg | 2 +-
tcl/target/str750.cfg | 2 +-
tcl/target/str912.cfg | 2 +-
tcl/target/tmpa900.cfg | 2 +-
tcl/target/tmpa910.cfg | 2 +-
tcl/target/xba_revA3.cfg | 2 +-
tcl/test/syntax1.cfg | 2 +-
45 files changed, 53 insertions(+), 46 deletions(-)
--- a/doc/openocd.texi
+++ b/doc/openocd.texi
@@ -3185,13 +3185,18 @@ since performing a backup slows down ope
For example, the beginning of an SRAM block is likely to
be used by most build systems, but the end is often unused.
-...@item @code{-work-area-size} @var{size} -- specify/set the work area
+...@item @code{-work-area-size} @var{size} -- specify work are size,
+in bytes. The same size applies regardless of whether its physical
+or virtual address is being used.
@item @code{-work-area-phys} @var{address} -- set the work area
base @var{address} to be used when no MMU is active.
@item @code{-work-area-virt} @var{address} -- set the work area
base @var{address} to be used when an MMU is active.
+...@emph{do not specify a value for this except on targets with an MMU.}
+The value should normally correspond to a static mapping for the
+...@code{-work-area-phys} address, set up by the current operating system.
@end itemize
@end deffn
--- a/tcl/board/at91sam9g20-ek.cfg
+++ b/tcl/board/at91sam9g20-ek.cfg
@@ -41,8 +41,8 @@ target create $_TARGETNAME arm926ejs -en
# AT91SAM9G20 has two SRAM areas, one starting at 0x00200000 and the other
starting at 0x00300000.
# Both areas are 16 kB long.
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x00200000
-work-area-size 0x4000 -work-area-backup 1
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x00300000
-work-area-size 0x4000 -work-area-backup 1
+#$_TARGETNAME configure -work-area-phys 0x00200000 -work-area-size 0x4000
-work-area-backup 1
+$_TARGETNAME configure -work-area-phys 0x00300000 -work-area-size 0x4000
-work-area-backup 1
# If you don't want to execute built-in boot rom code (and there are good
reasons at times not to do that) in the
# AT91SAM9 family, the microcontroller is a lump on a log without
initialization. Because this family has
--- a/tcl/board/digi_connectcore_wi-9c.cfg
+++ b/tcl/board/digi_connectcore_wi-9c.cfg
@@ -114,7 +114,7 @@ $_TARGETNAME configure -event reset-init
reg cpsr 0xd3
}
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x00000000
-work-area-size 0x1000 -work-area-backup 1
+$_TARGETNAME configure -work-area-phys 0x00000000 -work-area-size 0x1000
-work-area-backup 1
#####################
# Flash configuration
--- a/tcl/board/hitex_str9-comstick.cfg
+++ b/tcl/board/hitex_str9-comstick.cfg
@@ -65,7 +65,7 @@ $_TARGETNAME configure -event reset-init
flash protect 0 0 7 off
}
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x50000000
-work-area-size 16384 -work-area-backup 0
+$_TARGETNAME configure -work-area-phys 0x50000000 -work-area-size 16384
-work-area-backup 0
#flash bank <driver> <base> <size> <chip_width> <bus_width>
flash bank str9x 0x00000000 0x00080000 0 0 0
--- a/tcl/board/linksys_nslu2.cfg
+++ b/tcl/board/linksys_nslu2.cfg
@@ -4,5 +4,5 @@
source [find target/ixp42x.cfg]
# The _TARGETNAME is set by the above.
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x00020000
-work-area-size 0x10000 -work-area-backup 0
+$_TARGETNAME configure -work-area-phys 0x00020000 -work-area-size 0x10000
-work-area-backup 0
--- a/tcl/board/mini2440.cfg
+++ b/tcl/board/mini2440.cfg
@@ -104,7 +104,7 @@ jtag newtap $_CHIPNAME cpu -irlen 4 -irc
set _TARGETNAME [format "%s.cpu" $_CHIPNAME]
target create $_TARGETNAME arm920t -endian $_ENDIAN -chain-position
$_TARGETNAME -variant arm920t
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x40000000
-work-area-size 0x4000 -work-area-backup 1
+$_TARGETNAME configure -work-area-phys 0x40000000 -work-area-size 0x4000
-work-area-backup 1
#reset configuration
jtag_nsrst_delay 100
--- a/tcl/board/pxa255_sst.cfg
+++ b/tcl/board/pxa255_sst.cfg
@@ -10,7 +10,7 @@
source [find target/pxa255.cfg]
# Target name is set by above
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x4000000
-work-area-size 0x4000 -work-area-backup 0
+$_TARGETNAME configure -work-area-phys 0x4000000 -work-area-size 0x4000
-work-area-backup 0
# flash bank <driver> <base> <size> <chip_width> <bus_width> <target> [options]
flash bank cfi 0x00000000 0x80000 2 2 $_TARGETNAME jedec_probe
--- a/tcl/board/str910-eval.cfg
+++ b/tcl/board/str910-eval.cfg
@@ -39,7 +39,7 @@ jtag newtap $_CHIPNAME bs -irlen 5 -i
set _TARGETNAME [format "%s.cpu" $_CHIPNAME]
target create $_TARGETNAME arm966e -endian $_ENDIAN -chain-position
$_TARGETNAME -variant arm966e
-$_TARGETNAME configure -work-area-phys 0x50000000 -work-area-virt 0x50000000
-work-area-size 16384 -work-area-backup 1
+$_TARGETNAME configure -work-area-phys 0x50000000 -work-area-size 16384
-work-area-backup 1
$_TARGETNAME configure -event reset-init {
# We can increase speed now that we know the target is halted.
--- a/tcl/board/zy1000.cfg
+++ b/tcl/board/zy1000.cfg
@@ -63,7 +63,7 @@ $_TARGETNAME configure -event reset-init
# required for usable performance. Used for lots of
# other things than flash programming.
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x00020000
-work-area-size 0x20000 -work-area-backup 0
+$_TARGETNAME configure -work-area-phys 0x00020000 -work-area-size 0x20000
-work-area-backup 0
jtag_khz 16000
--- a/tcl/target/at91eb40a.cfg
+++ b/tcl/target/at91eb40a.cfg
@@ -46,7 +46,7 @@ flash bank ecosflash 0x01000000 0x200000
# required for usable performance. Used for lots of
# other things than flash programming.
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x00030000
-work-area-size 0x10000 -work-area-backup 0
+$_TARGETNAME configure -work-area-phys 0x00030000 -work-area-size 0x10000
-work-area-backup 0
$_TARGETNAME configure -event reset-init {
puts "Running reset init script for AT91EB40A"
--- a/tcl/target/at91r40008.cfg
+++ b/tcl/target/at91r40008.cfg
@@ -43,7 +43,7 @@ $_TARGETNAME configure -event gdb-flash-
mww 0xffe00020 0x00000001
}
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x3C000
-work-area-size 0x4000 -work-area-backup 0
+$_TARGETNAME configure -work-area-phys 0x3C000 -work-area-size 0x4000
-work-area-backup 0
flash bank cfi 0x10000000 0x400000 2 2 $_TARGETNAME
--- a/tcl/target/at91rm9200.cfg
+++ b/tcl/target/at91rm9200.cfg
@@ -42,7 +42,7 @@ set _TARGETNAME $_CHIPNAME.cpu
target create $_TARGETNAME arm920t -endian $_ENDIAN -chain-position
$_TARGETNAME
# AT91RM9200 has a 16K block of sram @ 0x0020.0000
-$_TARGETNAME configure -work-area-virt 0x00200000 -work-area-phys 0x00200000 \
+$_TARGETNAME configure -work-area-phys 0x00200000 \
-work-area-size 0x4000 -work-area-backup 1
# This chip has a DCC ... use it
--- a/tcl/target/at91sam3uXX.cfg
+++ b/tcl/target/at91sam3uXX.cfg
@@ -33,7 +33,7 @@ set _TARGETNAME $_CHIPNAME.cpu
target create $_TARGETNAME cortex_m3 -endian $_ENDIAN -chain-position
$_TARGETNAME
# 16K is plenty, the smallest chip has this much
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x20000000
-work-area-size 16384 -work-area-backup 0
+$_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size 16384
-work-area-backup 0
reset_config srst_only
--- a/tcl/target/at91sam7sx.cfg
+++ b/tcl/target/at91sam7sx.cfg
@@ -46,7 +46,7 @@ $_TARGETNAME configure -event reset-init
sleep 100
}
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x00200000
-work-area-size 0x4000 -work-area-backup 0
+$_TARGETNAME configure -work-area-phys 0x00200000 -work-area-size 0x4000
-work-area-backup 0
#flash bank <driver> <base_addr> <size> <chip_width> <bus_width>
<target_number> [<target_name> <banks> <sectors_per_bank> <pages_per_sector>
<page_size> <num_nvmbits> <ext_freq_khz>]
flash bank at91sam7 0 0 0 0 0 0 0 0 0 0 0 0 18432
--- a/tcl/target/at91sam9260.cfg
+++ b/tcl/target/at91sam9260.cfg
@@ -39,6 +39,6 @@ set _TARGETNAME $_CHIPNAME.cpu
target create $_TARGETNAME arm926ejs -endian $_ENDIAN -chain-position
$_TARGETNAME -variant arm926ejs
# Internal sram1 memory
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x00300000
-work-area-size 0x1000 -work-area-backup 1
+$_TARGETNAME configure -work-area-phys 0x00300000 -work-area-size 0x1000
-work-area-backup 1
--- a/tcl/target/at91sam9260_ext_RAM_ext_flash.cfg
+++ b/tcl/target/at91sam9260_ext_RAM_ext_flash.cfg
@@ -47,7 +47,7 @@ target create $_TARGETNAME arm926ejs -en
$_TARGETNAME invoke-event halted
# Internal sram1 memory
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x00300000
-work-area-size 0x1000 -work-area-backup 1
+$_TARGETNAME configure -work-area-phys 0x00300000 -work-area-size 0x1000
-work-area-backup 1
scan_chain
$_TARGETNAME configure -event reset-deassert-post {at91sam_init}
--- a/tcl/target/cs351x.cfg
+++ b/tcl/target/cs351x.cfg
@@ -24,7 +24,7 @@ target create $_TARGETNAME fa526 -endian
# There is 16K of SRAM on this chip
# FIXME: flash programming is not working by using this work area. So comment
this out for now.
-#$_TARGETNAME configure -work-area-virt 0x00000000 -work-area-phys 0x00000000
-work-area-size 0x4000 -work-area-backup 1
+#$_TARGETNAME configure -work-area-phys 0x00000000 -work-area-size 0x4000
-work-area-backup 1
# This chip has a DCC ... use it
arm7_9 dcc_downloads enable
--- a/tcl/target/epc9301.cfg
+++ b/tcl/target/epc9301.cfg
@@ -24,7 +24,7 @@ jtag_nsrst_delay 100
jtag_ntrst_delay 100
set _TARGETNAME $_CHIPNAME.cpu
-target create $_TARGETNAME arm920t -endian $_ENDIAN -chain-position
$_TARGETNAME -work-area-virt 0 -work-area-phys 0x80014000 -work-area-size
0x1000 -work-area-backup 1
+target create $_TARGETNAME arm920t -endian $_ENDIAN -chain-position
$_TARGETNAME -work-area-phys 0x80014000 -work-area-size 0x1000
-work-area-backup 1
#flash configuration
#flash bank <driver> <base> <size> <chip_width> <bus_width> [driver_options
...]
--- a/tcl/target/imx27.cfg
+++ b/tcl/target/imx27.cfg
@@ -40,7 +40,9 @@ jtag newtap $_CHIPNAME cpu -irlen 4 -ir
# Create the GDB Target.
set _TARGETNAME $_CHIPNAME.cpu
target create $_TARGETNAME arm926ejs -endian $_ENDIAN -chain-position
$_TARGETNAME -variant arm926ejs
-$_TARGETNAME configure -work-area-virt 0xffff4c00 -work-area-phys 0xffff4c00
-work-area-size 0x8000 -work-area-backup 1
+# REVISIT what operating environment sets up this virtual address mapping?
+$_TARGETNAME configure -work-area-virt 0xffff4c00 -work-area-phys 0xffff4c00 \
+ -work-area-size 0x8000 -work-area-backup 1
# Internal to the chip, there is 45K of SRAM
#
--- a/tcl/target/is5114.cfg
+++ b/tcl/target/is5114.cfg
@@ -46,4 +46,4 @@ $_TARGETNAME configure -event reset-init
# We can increase speed now that we know the target is halted.
jtag_rclk 3000
}
-$_TARGETNAME configure -work-area-phys 0x50000000 -work-area-virt 0x50000000
-work-area-size 16384 -work-area-backup 1
+$_TARGETNAME configure -work-area-phys 0x50000000 -work-area-size 16384
-work-area-backup 1
--- a/tcl/target/lpc1768.cfg
+++ b/tcl/target/lpc1768.cfg
@@ -31,7 +31,7 @@ set _TARGETNAME $_CHIPNAME.cpu
target create $_TARGETNAME cortex_m3 -endian $_ENDIAN -chain-position
$_TARGETNAME
# LPC1768 has 32kB of SRAM on its main system bus (so-called Local On-Chip
SRAM)
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x10000000
-work-area-size 0x8000 -work-area-backup 0
+$_TARGETNAME configure -work-area-phys 0x10000000 -work-area-size 0x8000
-work-area-backup 0
$_TARGETNAME configure -event reset-init {
# Force target into ARM state
--- a/tcl/target/lpc2103.cfg
+++ b/tcl/target/lpc2103.cfg
@@ -31,7 +31,7 @@ set _TARGETNAME $_CHIPNAME.cpu
target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position
$_TARGETNAME -variant arm7tdmi-s_r4
# 8kB of internal SRAM
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x40000000
-work-area-size 0x2000 -work-area-backup 0
+$_TARGETNAME configure -work-area-phys 0x40000000 -work-area-size 0x2000
-work-area-backup 0
# 32kB of internal Flash, core clocked with 12MHz crystal
# flash bank lpc2000 <base> <size> 0 0 <target#> <variant> <clock>
[calc_checksum]
--- a/tcl/target/lpc2124.cfg
+++ b/tcl/target/lpc2124.cfg
@@ -35,7 +35,7 @@ jtag newtap $_CHIPNAME cpu -irlen 4 -irc
set _TARGETNAME $_CHIPNAME.cpu
target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position
$_TARGETNAME -variant arm7tdmi-s_r4
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x40000000
-work-area-size 0x4000 -work-area-backup 0
+$_TARGETNAME configure -work-area-phys 0x40000000 -work-area-size 0x4000
-work-area-backup 0
#flash bank <driver> <base> <size> <chip_width> <bus_width>
--- a/tcl/target/lpc2129.cfg
+++ b/tcl/target/lpc2129.cfg
@@ -35,7 +35,7 @@ jtag newtap $_CHIPNAME cpu -irlen 4 -irc
set _TARGETNAME $_CHIPNAME.cpu
target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position
$_TARGETNAME -variant arm7tdmi-s_r4
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x40000000
-work-area-size 0x4000 -work-area-backup 0
+$_TARGETNAME configure -work-area-phys 0x40000000 -work-area-size 0x4000
-work-area-backup 0
#flash bank <driver> <base> <size> <chip_width> <bus_width>
flash bank lpc2000 0x0 0x40000 0 0 $_TARGETNAME lpc2000_v1 14765 calc_checksum
--- a/tcl/target/lpc2148.cfg
+++ b/tcl/target/lpc2148.cfg
@@ -35,7 +35,7 @@ jtag newtap $_CHIPNAME cpu -irlen 4 -irc
set _TARGETNAME $_CHIPNAME.cpu
target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position
$_TARGETNAME -variant arm7tdmi-s_r4
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x40000000
-work-area-size 0x4000 -work-area-backup 0
+$_TARGETNAME configure -work-area-phys 0x40000000 -work-area-size 0x4000
-work-area-backup 0
$_TARGETNAME configure -event reset-init {
# Force target into ARM state
--- a/tcl/target/lpc2294.cfg
+++ b/tcl/target/lpc2294.cfg
@@ -28,7 +28,7 @@ jtag newtap $_CHIPNAME cpu -irlen 4 -irc
set _TARGETNAME $_CHIPNAME.cpu
target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position
$_TARGETNAME -variant arm7tdmi-s_r4
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x40000000
-work-area-size 0x4000 -work-area-backup 0
+$_TARGETNAME configure -work-area-phys 0x40000000 -work-area-size 0x4000
-work-area-backup 0
#flash configuration
#flash bank lpc2000 <base> <size> 0 0 <target#> <variant>
--- a/tcl/target/lpc2378.cfg
+++ b/tcl/target/lpc2378.cfg
@@ -31,7 +31,7 @@ set _TARGETNAME $_CHIPNAME.cpu
target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position
$_TARGETNAME -variant arm7tdmi-s_r4
# LPC2378 has 32kB of SRAM on its main system bus (so-called Local On-Chip
SRAM)
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x40000000
-work-area-size 0x8000 -work-area-backup 0
+$_TARGETNAME configure -work-area-phys 0x40000000 -work-area-size 0x8000
-work-area-backup 0
$_TARGETNAME configure -event reset-init {
# Force target into ARM state
--- a/tcl/target/lpc2478.cfg
+++ b/tcl/target/lpc2478.cfg
@@ -31,7 +31,7 @@ set _TARGETNAME $_CHIPNAME.cpu
target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position
$_TARGETNAME -variant arm7tdmi-s_r4
# LPC2478 has 64kB of SRAM on its main system bus (so-called Local On-Chip
SRAM)
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x40000000
-work-area-size 0x10000 -work-area-backup 0
+$_TARGETNAME configure -work-area-phys 0x40000000 -work-area-size 0x10000
-work-area-backup 0
$_TARGETNAME configure -event reset-init {
# Force target into ARM state
--- a/tcl/target/mega128.cfg
+++ b/tcl/target/mega128.cfg
@@ -20,7 +20,7 @@ jtag newtap $_CHIPNAME cpu -irlen 4 -irc
set _TARGETNAME $_CHIPNAME.cpu
target create $_TARGETNAME avr -endian $_ENDIAN -chain-position $_TARGETNAME
-#$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x20000000
-work-area-size 16384 -work-area-backup 0
+#$_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size 16384
-work-area-backup 0
flash bank avr 0 0 0 0 0
--- a/tcl/target/omap5912.cfg
+++ b/tcl/target/omap5912.cfg
@@ -48,5 +48,5 @@ proc omap5912_reset {} {
}
# omap5912 lcd frame buffer as working area
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x20000000 \
+$_TARGETNAME configure -work-area-phys 0x20000000 \
-work-area-size 0x3e800 -work-area-backup 0
--- a/tcl/target/pic32mx.cfg
+++ b/tcl/target/pic32mx.cfg
@@ -31,7 +31,7 @@ jtag newtap $_CHIPNAME cpu -irlen 5 -ir
set _TARGETNAME $_CHIPNAME.cpu
target create $_TARGETNAME mips_m4k -endian $_ENDIAN -chain-position
$_TARGETNAME
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0xa0000000
-work-area-size 16384 -work-area-backup 0
+$_TARGETNAME configure -work-area-phys 0xa0000000 -work-area-size 16384
-work-area-backup 0
flash bank pic32mx 0xbd000000 0 0 0 0
flash bank pic32mx 0xbfc00000 0 0 0 0
--- a/tcl/target/pxa270.cfg
+++ b/tcl/target/pxa270.cfg
@@ -41,4 +41,4 @@ jtag newtap $_CHIPNAME cpu -irlen 7 -irc
target create $_TARGETNAME xscale -endian $_ENDIAN -chain-position
$_TARGETNAME -variant pxa27x
# maps to PXA internal RAM. If you are using a PXA255
# you must initialize SDRAM or leave this option off
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x5c000000
-work-area-size 0x10000 -work-area-backup 0
+$_TARGETNAME configure -work-area-phys 0x5c000000 -work-area-size 0x10000
-work-area-backup 0
--- a/tcl/target/sam7se512.cfg
+++ b/tcl/target/sam7se512.cfg
@@ -32,7 +32,7 @@ jtag newtap $_CHIPNAME cpu -irlen 4 -irc
set _TARGETNAME $_CHIPNAME.cpu
target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position
$_TARGETNAME -variant arm7tdmi
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x00200000
-work-area-size 0x4000 -work-area-backup 0
+$_TARGETNAME configure -work-area-phys 0x00200000 -work-area-size 0x4000
-work-area-backup 0
#flash bank <driver> <base_addr> <size> <chip_width> <bus_width>
<target_number> [<target_name> <banks> <sectors_per_bank> <pages_per_sector>
<page_size> <num_nvmbits> <ext_freq_khz>]
flash bank at91sam7 0 0 0 0 0 0 0 0 0 0 0 0 18432
--- a/tcl/target/sam7x256.cfg
+++ b/tcl/target/sam7x256.cfg
@@ -43,7 +43,7 @@ $_TARGETNAME configure -event reset-init
sleep 100
}
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x00200000
-work-area-size 0x4000 -work-area-backup 0
+$_TARGETNAME configure -work-area-phys 0x00200000 -work-area-size 0x4000
-work-area-backup 0
#flash bank <driver> <base_addr> <size> <chip_width> <bus_width>
<target_number> [<target_name> <banks> <sectors_per_bank> <pages_per_sector>
<page_size> <num_nvmbits> <ext_freq_khz>]
flash bank at91sam7 0 0 0 0 0 0 0 0 0 0 0 0 18432
--- a/tcl/target/samsung_s3c2410.cfg
+++ b/tcl/target/samsung_s3c2410.cfg
@@ -28,7 +28,7 @@ jtag newtap $_CHIPNAME cpu -irlen 4 -irc
set _TARGETNAME $_CHIPNAME.cpu
target create $_TARGETNAME arm920t -endian $_ENDIAN -chain-position
$_TARGETNAME -variant arm920t
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x30800000
-work-area-size 0x20000 -work-area-backup 0
+$_TARGETNAME configure -work-area-phys 0x30800000 -work-area-size 0x20000
-work-area-backup 0
# speed up memory downloads
arm7_9 fast_memory_access enable
--- a/tcl/target/samsung_s3c2440.cfg
+++ b/tcl/target/samsung_s3c2440.cfg
@@ -29,7 +29,7 @@ jtag newtap $_CHIPNAME cpu -irlen 4 -irc
set _TARGETNAME $_CHIPNAME.cpu
target create $_TARGETNAME arm920t -endian $_ENDIAN -chain-position
$_TARGETNAME -variant arm920t
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x200000
-work-area-size 0x4000 -work-area-backup 1
+$_TARGETNAME configure -work-area-phys 0x200000 -work-area-size 0x4000
-work-area-backup 1
#reset configuration
reset_config trst_and_srst
--- a/tcl/target/stm32.cfg
+++ b/tcl/target/stm32.cfg
@@ -63,7 +63,7 @@ jtag newtap $_CHIPNAME bs -irlen 5 -expe
set _TARGETNAME $_CHIPNAME.cpu
target create $_TARGETNAME cortex_m3 -endian $_ENDIAN -chain-position
$_TARGETNAME
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x20000000
-work-area-size $_WORKAREASIZE -work-area-backup 0
+$_TARGETNAME configure -work-area-phys 0x20000000 -work-area-size
$_WORKAREASIZE -work-area-backup 0
flash bank stm32x 0 0 0 0 $_TARGETNAME
--- a/tcl/target/str710.cfg
+++ b/tcl/target/str710.cfg
@@ -36,7 +36,7 @@ $_TARGETNAME configure -event gdb-flash-
flash protect 1 0 1 off
}
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x2000C000
-work-area-size 0x4000 -work-area-backup 0
+$_TARGETNAME configure -work-area-phys 0x2000C000 -work-area-size 0x4000
-work-area-backup 0
#flash bank str7x <base> <size> 0 0 <target#> <variant>
flash bank str7x 0x40000000 0x00040000 0 0 0 STR71x
--- a/tcl/target/str730.cfg
+++ b/tcl/target/str730.cfg
@@ -40,7 +40,7 @@ $_TARGETNAME configure -event gdb-flash-
flash protect 0 0 7 off
}
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x40000000
-work-area-size 0x4000 -work-area-backup 0
+$_TARGETNAME configure -work-area-phys 0x40000000 -work-area-size 0x4000
-work-area-backup 0
#flash bank <driver> <base> <size> <chip_width> <bus_width>
flash bank str7x 0x20000000 0x00040000 0 0 0 STR3x
--- a/tcl/target/str750.cfg
+++ b/tcl/target/str750.cfg
@@ -43,7 +43,7 @@ $_TARGETNAME configure -event gdb-flash-
flash protect 1 0 1 off
}
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x40000000
-work-area-size 0x4000 -work-area-backup 0
+$_TARGETNAME configure -work-area-phys 0x40000000 -work-area-size 0x4000
-work-area-backup 0
#flash bank <driver> <base> <size> <chip_width> <bus_width>
flash bank str7x 0x20000000 0x00040000 0 0 0 STR75x
--- a/tcl/target/str912.cfg
+++ b/tcl/target/str912.cfg
@@ -60,7 +60,7 @@ $_TARGETNAME configure -event reset-init
flash protect 0 0 7 off
}
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x50000000
-work-area-size 16384 -work-area-backup 0
+$_TARGETNAME configure -work-area-phys 0x50000000 -work-area-size 16384
-work-area-backup 0
#flash bank str9x <base> <size> 0 0 <target#> <variant>
flash bank str9x 0x00000000 0x00080000 0 0 0
--- a/tcl/target/tmpa900.cfg
+++ b/tcl/target/tmpa900.cfg
@@ -52,5 +52,5 @@ target create $_TARGETNAME arm926ejs -en
#working_area 0 0xf8004000 0xc000 nobackup
# Internal sram1 memory
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0xf8004000
-work-area-size 0x8000 \
+$_TARGETNAME configure -work-area-phys 0xf8004000 -work-area-size 0x8000 \
-work-area-backup 0
--- a/tcl/target/tmpa910.cfg
+++ b/tcl/target/tmpa910.cfg
@@ -52,5 +52,5 @@ target create $_TARGETNAME arm926ejs -en
#working_area 0 0xf8004000 0xc000 nobackup
# Internal sram1 memory
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0xf8004000
-work-area-size 0xc000 \
+$_TARGETNAME configure -work-area-phys 0xf8004000 -work-area-size 0xc000 \
-work-area-backup 0
--- a/tcl/target/xba_revA3.cfg
+++ b/tcl/target/xba_revA3.cfg
@@ -76,7 +76,7 @@ $_TARGETNAME configure -event reset-init
flash probe 0
}
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x20010000
-work-area-size 0x8060 -work-area-backup 0
+$_TARGETNAME configure -work-area-phys 0x20010000 -work-area-size 0x8060
-work-area-backup 0
flash bank cfi 0x50000000 0x400000 2 2 $_TARGETNAME
--- a/tcl/test/syntax1.cfg
+++ b/tcl/test/syntax1.cfg
@@ -16,7 +16,7 @@ jtag newtap lpc2148 one -irlen 4 -ircapt
#daemon_startup reset
set _TARGETNAME [format "%s.cpu" lpc2148]
-target create lpc2148.cpu arm7tdmi -endian little -work-area-size 0x4000
-work-area-phys 0x40000000 -work-area-virt 0 -work-area-backup 0
+target create lpc2148.cpu arm7tdmi -endian little -work-area-size 0x4000
-work-area-phys 0x40000000 -work-area-backup 0
$_TARGETNAME configure -event reset-init {
soft_reset_halt
_______________________________________________
Openocd-development mailing list
Openocd-development@lists.berlios.de
https://lists.berlios.de/mailman/listinfo/openocd-development
