Committed.
Thanks!
On Sat, Aug 8, 2009 at 1:31 PM, Xiaofan Chen<xiaof...@gmail.com> wrote:
> The following patch splits LM3S811 config file into target file and board
> file.
> I also modified the target config file based on the some suggestions of David
> Brownell on the LM3S1968 file.
>
> But I do not have the board. Hopefully the patch is ok to be commited.
>
> Index: tcl/target/lm3s811.cfg
> ===================================================================
> --- tcl/target/lm3s811.cfg (revision 2578)
> +++ tcl/target/lm3s811.cfg (working copy)
> @@ -1,4 +1,4 @@
> -# Script for luminary lm3s811
> +# Script for TI/Luminary Stellaris LM3S811
>
> if { [info exists CHIPNAME] } {
> set _CHIPNAME $CHIPNAME
> @@ -16,26 +16,16 @@
> if { [info exists CPUTAPID ] } {
> set _CPUTAPID $CPUTAPID
> } else {
> - # force an error till we get a good number
> set _CPUTAPID 0x3ba00477
> }
>
> -# jtag speed
> -jtag_khz 500
> -
> -jtag_nsrst_delay 100
> -jtag_ntrst_delay 100
> -
> -#LM3S811 Evaluation Board has only srst
> -reset_config srst_only
> -
> #jtag scan chain
> jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 1 -irmask 0xf
> -expected-id $_CPUTAPID
>
> # the luminary variant causes a software reset rather than asserting SRST
> # this stops the debug registers from being cleared
> # this will be fixed in later revisions of silicon
> -set _TARGETNAME [format "%s.cpu" $_CHIPNAME]
> +set _TARGETNAME $_CHIPNAME.cpu
> target create $_TARGETNAME cortex_m3 -endian $_ENDIAN -chain-position
> $_TARGETNAME -variant lm3s
>
> # 8k working area at base of ram
> Index: tcl/board/ek-lm3s811.cfg
> ===================================================================
> --- tcl/board/ek-lm3s811.cfg (revision 0)
> +++ tcl/board/ek-lm3s811.cfg (revision 0)
> @@ -0,0 +1,19 @@
> +#
> +# TI/Luminary Stellaris LM3S811 Evaluation Kits
> +#
> +# http://www.luminarymicro.com/products/stellaris_811_evaluation_kits.html
> +
> +# include the FT2232 interface config for on-board JTAG interface
> +source [find interface/luminary.cfg]
> +
> +# include the target config
> +source [find target/lm3s811.cfg]
> +
> +# jtag speed
> +jtag_khz 500
> +
> +jtag_nsrst_delay 100
> +jtag_ntrst_delay 100
> +
> +#LM3S811 Evaluation Board has only srst
> +reset_config srst_only
>
>
> --
> Xiaofan http://mcuee.blogspot.com
>
> _______________________________________________
> Openocd-development mailing list
> Openocd-development@lists.berlios.de
> https://lists.berlios.de/mailman/listinfo/openocd-development
>
>
--
Øyvind Harboe
Embedded software and hardware consulting services
http://www.zylin.com
_______________________________________________
Openocd-development mailing list
Openocd-development@lists.berlios.de
https://lists.berlios.de/mailman/listinfo/openocd-development
