Make the Hitex STM32-PerformanceStick board config behave better:
source the STM32 target config instead of using a private clone.
The same should evidently be done with the STR750 chip on this
board, but the str750.cfg looks like quite a mess ... I'm not
sure which board it's expecting, but it's likely not this one.
---
tcl/board/hitex_stm32-performancestick.cfg | 47 +--------------------------
1 file changed, 3 insertions(+), 44 deletions(-)
NOTE: not tested, I don't have this hardware.
Make the Hitex STM32-PerformanceStick board config behave better:
source the STM32 target config instead of using a private clone.
The same should evidently be done with the STR750 chip on this
board, but the str750.cfg looks like quite a mess ... I'm not
sure which board it's expecting, but it's likely not this one.
---
tcl/board/hitex_stm32-performancestick.cfg | 47 +--------------------------
1 file changed, 3 insertions(+), 44 deletions(-)
--- a/tcl/board/hitex_stm32-performancestick.cfg
+++ b/tcl/board/hitex_stm32-performancestick.cfg
@@ -1,50 +1,9 @@
# Hitex stm32 performance stick
-if { [info exists CHIPNAME] } {
- set _CHIPNAME $CHIPNAME
-} else {
- set _CHIPNAME stm32_hitex
-}
-
-if { [info exists ENDIAN] } {
- set _ENDIAN $ENDIAN
-} else {
- set _ENDIAN little
-}
-
-# set jtag speed
-jtag_khz 500
-
-jtag_nsrst_delay 100
-jtag_ntrst_delay 100
-
-#use combined on interfaces or targets that can't set TRST/SRST separately
-reset_config trst_and_srst
-
-#jtag scan chain
-# The CPU
-if { [info exists CPUTAPID ] } {
- set _CPUTAPID $CPUTAPID
-} else {
- # See STM Document RM0008
- # Section 26.6.3
- set _CPUTAPID 0x3ba00477
-}
-jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID
-
-# The boundery scan register, leave the "expected-id" undefined.
-jtag newtap $_CHIPNAME bs -irlen 5 -ircapture 0x1 -irmask 0x1
+set CHIPNAME stm32_hitex
+source [find target/stm32.cfg]
# configure str750 connected to jtag chain
+# FIXME -- source [find target/str750.cfg] after cleaning that up
jtag newtap $_CHIPNAME unknown -irlen 4 -ircapture 0x1 -irmask 0x0f
-set _TARGETNAME [format "%s.cpu" $_CHIPNAME]
-target create $_TARGETNAME cortex_m3 -endian $_ENDIAN -chain-position $_TARGETNAME
-
-$_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x20000000 -work-area-size 16384 -work-area-backup 0
-
-#
-flash bank stm32x 0 0 0 0 0
-
-# For more information about the configuration files, take a look at:
-# openocd.texi
_______________________________________________
Openocd-development mailing list
Openocd-development@lists.berlios.de
https://lists.berlios.de/mailman/listinfo/openocd-development
