I tried openocd r1836 and r1938 with the same results. I need to flash an AT91SAM7X256 (the board is evaluation buord from atmel) with an Amontec jtagkey-tiny. My PC runs ubuntu linux 8.10 64bit, and I use libftdi 0.16 (configured as defaults) PC is an intel core2 q8300 and 4GB ram
I run openocd with the following command line $ sudo openocd -f scrips/jtagkey.cfg -f scrips/sam7x256.cfg -d 3 with scrips: ----8<------- jtagkey.cfg ----8<------- # # Amontec JTAGkey # # http://www.amontec.com/jtagkey.shtml # #daemon configuration telnet_port 4444 gdb_port 3333 interface ft2232 ft2232_device_desc "Amontec JTAGkey A" ft2232_layout jtagkey ft2232_vid_pid 0x0403 0xcff8 ----8<-----------8<-----------8<------- and ----8<------- sam7x256.cfg ----8<------- #use combined on interfaces or targets that can't set TRST/SRST separately reset_config srst_only srst_pulls_trst if { [info exists CHIPNAME] } { set _CHIPNAME $CHIPNAME } else { set _CHIPNAME sam7x256 } if { [info exists ENDIAN] } { set _ENDIAN $ENDIAN } else { set _ENDIAN little } if { [info exists CPUTAPID ] } { set _CPUTAPID $CPUTAPID } else { set _CPUTAPID 0x3f0f0f0f } jtag newtap $_CHIPNAME cpu -irlen 4 -ircapture 0x1 -irmask 0xf -expected-id $_CPUTAPID set _TARGETNAME [format "%s.cpu" $_CHIPNAME] target create $_TARGETNAME arm7tdmi -endian $_ENDIAN -chain-position $_TARGETNAME -variant arm7tdmi $_TARGETNAME configure -event reset-init { # disable watchdog mww 0xfffffd44 0x00008000 # enable user reset mww 0xfffffd08 0xa5000001 # CKGR_MOR : enable the main oscillator mww 0xfffffc20 0x00000601 sleep 10 # CKGR_PLLR: 96.1097 MHz mww 0xfffffc2c 0x00481c0e sleep 10 # PMC_MCKR : MCK = PLL / 2 ~= 48 MHz mww 0xfffffc30 0x00000007 sleep 10 # MC_FMR: flash mode (FWS=1,FMCN=60) mww 0xffffff60 0x003c0100 sleep 100 } $_TARGETNAME configure -work-area-virt 0 -work-area-phys 0x00200000 -work-area-size 0x4000 -work-area-backup 0 #flash bank <driver> <base> <size> <chip_width> <bus_width> flash bank at91sam7 0 0 0 0 0 # For more information about the configuration files, take a look at: # openocd.texi ----8<-----------8<-----------8<------- then I connect via telnet to 4444 port I run the following commands > arm7_9 dcc_downloads enable dcc downloads are enabled > arm7_9 fast_memory_access enable fast memory access is enabled > flash write_image erase firmware.bin 0x100000 bin auto erase enabled wrote 44616 byte from file firmware.bin in 11.045264s (3.944705 kb/s) openocd (both r1836 and r1938) are configured using first bootstrap and ./configure --enable-ft2232_libftdi --disable-werror --enable-maintainer-mode I attach debug trace outputed from openocd. what is wrong? How can I speed up the process? Maybe the opensource libftdi? Do I need to try with ftd2xx driver provided by Amontec? I don't think that is for 64bit systems, isn't it? thanks -- Assioma di Cole: "La somma dell'intelligenza sulla Terra è costante; la popolazione è in aumento" Massimiliano Cialdi cia...@gmail.com massimiliano.cia...@powersoft.it
debug_trace.txt.gz
Description: GNU Zip compressed data
_______________________________________________ Openocd-development mailing list Openocd-development@lists.berlios.de https://lists.berlios.de/mailman/listinfo/openocd-development
