Could you send me the config file you used ?
Thanks, jesus 2009/4/8 Magnus Lundin <lun...@mlu.mine.nu> > Hi, > > I have resently made some test on the same board but with a ft2232 based > interface. > The configuration that works best so far uses: > > #use combined on interfaces or targets that can't set TRST/SRST separately > reset_config trst_and_srst srst_pulls_trst > jtag_nsrst_delay 10 > jtag_khz 1000 > > The LPC2129 based boards should work with the same config files. > > Regards, > Magnus > > Jesus Sanchez-Palencia wrote: > > Hey guys, > > > > I'm trying to "translate" and old config file for LPC-E2124 (Olimex), > > because it has some deprecated functions. I'm sending attached both > config > > files, the old one and the one I'm working on right now. > > > > I've already managed to communicate with the board, but something still > > seems to be wrong. This is my first experience with OpenOCD, but as soon > as > > this cfg file becames ready I intend to send it to your svn. (yes, I'll > > clean it a little bit) > > > > So, I can start OpenOCD and can connect to its GDB server but at this > point > > I already have some warnings. If I give some "monitor step" or "monitor > > resume" everything just go fine. I can even set a BP, with just some > "data > > abort" message. But if I try to do some "monitor reset [anything]" I have > > some errors, and have to do a hard-reset at the board (reset button). > > > > Below are the messages from OpenOCD with the steps above mentioned. What > do > > you think ?! > > Anything wrong with my new config file ? > > > > > > ------------------------ CUT ----------------------------------------- > > > > j...@andaluzia ~/dev/openocd/trunk/src $ sudo ./openocd -f > > lpc2124+armjtag.cfg > > Open On-Chip Debugger 1.0 (2009-04-06-19:24) svn:1435 > > > > > > BUGS? Read http://svn.berlios.de/svnroot/repos/openocd/trunk/BUGS > > > > > > $URL: svn://svn.berlios.de/openocd/trunk/src/openocd.c $ > > jtag_speed: 0 > > Info : JTAG tap: lpc2124.cpu tap/device found: 0x4f1f0f0f (Manufacturer: > > 0x787, Part: 0xf1f0, Version: 0x4) > > Info : JTAG Tap/device matched > > Warn : no tcl port specified, using default port 6666 > > Info : accepting 'gdb' connection from 0 > > target state: halted > > target halted in Thumb state due to debug-request, current mode: System > > cpsr: 0x600000ff pc: 0x00003e58 > > Warn : acknowledgment received, but no packet pending > > Warn : memory read caused data abort (address: 0x08080808, size: 0x4, > count: > > 0x2) > > Warn : memory read caused data abort (address: 0x08080808, size: 0x4, > count: > > 0x1) > > > > > > target state: halted > > target halted in Thumb state due to single-step, current mode: System > > cpsr: 0x600000ff pc: 0x00003e5a > > target state: halted > > target halted in Thumb state due to single-step, current mode: System > > cpsr: 0x800000ff pc: 0x00003e5c > > Warn : memory read caused data abort (address: 0x20000000, size: 0x2, > count: > > 0x1) > > breakpoint added at address 0x20000000 > > > > > > Info : JTAG tap: lpc2124.cpu tap/device found: 0x4f1f0f0f (Manufacturer: > > 0x787, Part: 0xf1f0, Version: 0x4) > > Info : JTAG Tap/device matched > > Error: invalid mode value encountered > > Error: cpsr contains invalid mode value - communication failure > > > > > > ------------------------ CUT ----------------------------------------- > > > > > > > > > > Thanks in advance, > > jesus > > > > > > ------------------------------------------------------------------------ > > > > _______________________________________________ > > Openocd-development mailing list > > Openocd-development@lists.berlios.de > > https://lists.berlios.de/mailman/listinfo/openocd-development > > > > _______________________________________________ > Openocd-development mailing list > Openocd-development@lists.berlios.de > https://lists.berlios.de/mailman/listinfo/openocd-development >
_______________________________________________ Openocd-development mailing list Openocd-development@lists.berlios.de https://lists.berlios.de/mailman/listinfo/openocd-development
