On 05/01/2012 09:14 PM, Darren Hart wrote:
Fixes [YOCTO #2385]
The installer only searches for hd[ab] sd[ab]. Some newer BSPs have mmcblk
devices that should be used as the install target. These devices also have a
partition prefix (mmcblk0p1 instead of mmcblk01). As they are detected
asynchronously, it is necessary to add the rootwait kernel parameter to avoid
a race condition trying to mount the root device.
As BSPs like the FRI2 and the sys940x have mmc devices and will have a 1.2
release, we should push this to 1.2.1. The changes are perfectly contained and
easily verified.
Test for an mmcblk device and add the p partition prefix if necessary. Add the
rootwait kernel parameter when an mmcblk device is detected. Replace the series
of explicit umount commands with a single umount using a wildcard. This will
find all the partitions and will not try to unmount non-existant devices. Avoid
copy and paste errors by replacing /dev/${device}${pX} references with the
previously assigned rootfs, bootfs, and swap variables.
These changes have been tested on the FRI2 Sato image which installed to
/dev/mmcblk0 as well as the N450 Sato image which installed to /dev/sda. Both
were successful.
Please apply to master as well as the 1.2.1 branch.
I modified this commit log to remove [1.2.1] from the title as well as
your sentence at the end referring to 1.2.1. In the future, all that's
necessary is to mention 1.2.1 in the cover letter, not the actual commits.
Merged to denzil-next, thanks!
http://git.openembedded.org/openembedded-core-contrib/log/?h=sgarman/denzil-next
Scott
Signed-off-by: Darren Hart<dvh...@linux.intel.com>
CC: Scott Garman<scott.a.gar...@intel.com>
---
.../initrdscripts/files/init-install.sh | 45 ++++++++++---------
.../initrdscripts/initramfs-live-install_1.0.bb | 2 +-
2 files changed, 25 insertions(+), 22 deletions(-)
diff --git a/meta/recipes-core/initrdscripts/files/init-install.sh
b/meta/recipes-core/initrdscripts/files/init-install.sh
index 90978dd..01ff829 100644
--- a/meta/recipes-core/initrdscripts/files/init-install.sh
+++ b/meta/recipes-core/initrdscripts/files/init-install.sh
@@ -16,7 +16,7 @@ swap_ratio=5
found="no"
echo "Searching for a hard drive..."
-for device in 'hda' 'hdb' 'sda' 'sdb'
+for device in 'hda' 'hdb' 'sda' 'sdb' 'mmcblk0' 'mmcblk1'
do
if [ -e /sys/block/${device}/removable ]; then
if [ "$(cat /sys/block/${device}/removable)" = "0" ]; then
@@ -62,13 +62,7 @@ rm -f /etc/udev/scripts/mount*
#
# Unmount anything the automounter had mounted
#
-umount /dev/${device} 2> /dev/null || /bin/true
-umount /dev/${device}1 2> /dev/null || /bin/true
-umount /dev/${device}2 2> /dev/null || /bin/true
-umount /dev/${device}3 2> /dev/null || /bin/true
-umount /dev/${device}4 2> /dev/null || /bin/true
-umount /dev/${device}5 2> /dev/null || /bin/true
-umount /dev/${device}6 2> /dev/null || /bin/true
+umount /dev/${device}* 2> /dev/null || /bin/true
if [ ! -b /dev/sda ] ; then
mknod /dev/sda b 8 0
@@ -94,14 +88,23 @@ rootfs_start=$((boot_size + 1))
rootfs_end=$((rootfs_start+rootfs_size))
swap_start=$((rootfs_end+1))
-bootfs=/dev/${device}1
-rootfs=/dev/${device}2
-swap=/dev/${device}3
+# MMC devices are special in a couple of ways
+# 1) they use a partition prefix character 'p'
+# 2) they are detected asynchronously (need rootwait)
+rootwait=""
+part_prefix=""
+if [ ! "${device#mmcblk}" = "${device}" ]; then
+ part_prefix="p"
+ rootwait="rootwait"
+fi
+bootfs=/dev/${device}${part_prefix}1
+rootfs=/dev/${device}${part_prefix}2
+swap=/dev/${device}${part_prefix}3
echo "*****************"
-echo "Boot partition size: $boot_size MB (/dev/${device}1)"
-echo "Rootfs partition size: $rootfs_size MB (/dev/${device}2)"
-echo "Swap partition size: $swap_size MB (/dev/${device}3)"
+echo "Boot partition size: $boot_size MB ($bootfs)"
+echo "Rootfs partition size: $rootfs_size MB ($rootfs)"
+echo "Swap partition size: $swap_size MB ($swap)"
echo "*****************"
echo "Deleting partition table on /dev/${device} ..."
dd if=/dev/zero of=/dev/${device} bs=512 count=2
@@ -109,24 +112,24 @@ dd if=/dev/zero of=/dev/${device} bs=512 count=2
echo "Creating new partition table on /dev/${device} ..."
parted /dev/${device} mklabel msdos
-echo "Creating boot partition on /dev/${device}1"
+echo "Creating boot partition on $bootfs"
parted /dev/${device} mkpart primary 1 $boot_size
-echo "Creating rootfs partition on /dev/${device}2"
+echo "Creating rootfs partition on $rootfs"
parted /dev/${device} mkpart primary $rootfs_start $rootfs_end
-echo "Creating swap partition on /dev/${device}3"
+echo "Creating swap partition on $swap"
parted /dev/${device} mkpart primary $swap_start $disk_size
parted /dev/${device} print
-echo "Formatting /dev/${device}1 to ext2..."
+echo "Formatting $bootfs to ext2..."
mkfs.ext3 $bootfs
-echo "Formatting /dev/${device}2 to ext3..."
+echo "Formatting $rootfs to ext3..."
mkfs.ext3 $rootfs
-echo "Formatting swap partition...(/dev/${device}3)"
+echo "Formatting swap partition...($swap)"
mkswap $swap
mkdir /ssd
@@ -150,7 +153,7 @@ fi
if [ -f /ssd/etc/grub.d/40_custom ] ; then
echo "Preparing custom grub2 menu..."
- sed -i "s@__ROOTFS__@$rootfs@g" /ssd/etc/grub.d/40_custom
+ sed -i "s@__ROOTFS__@$rootfs $rootwait@g" /ssd/etc/grub.d/40_custom
sed -i "s/__VIDEO_MODE__/$3/g" /ssd/etc/grub.d/40_custom
sed -i "s/__VGA_MODE__/$4/g" /ssd/etc/grub.d/40_custom
mount $bootfs /bootmnt
diff --git a/meta/recipes-core/initrdscripts/initramfs-live-install_1.0.bb
b/meta/recipes-core/initrdscripts/initramfs-live-install_1.0.bb
index 793a4b7..ac73ef8 100644
--- a/meta/recipes-core/initrdscripts/initramfs-live-install_1.0.bb
+++ b/meta/recipes-core/initrdscripts/initramfs-live-install_1.0.bb
@@ -3,7 +3,7 @@ LICENSE = "MIT"
LIC_FILES_CHKSUM =
"file://${COREBASE}/meta/COPYING.MIT;md5=3da9cfbcb788c80a0384361b4de20420"
SRC_URI = "file://init-install.sh"
-PR = "r6"
+PR = "r7"
RDEPENDS_${PN} = "grub parted e2fsprogs-mke2fs"
--
Scott Garman
Embedded Linux Engineer - Yocto Project
Intel Open Source Technology Center
_______________________________________________
Openembedded-core mailing list
Openembedded-core@lists.openembedded.org
http://lists.linuxtogo.org/cgi-bin/mailman/listinfo/openembedded-core
